Iomegaメーカー03798300の使用説明書/サービス説明書
ページ先へ移動 of 48
Internal A T API Driv e Owner ’ s Manual • Installation Guide • User’ s Guide • T roubleshooting • How to Get Help IMPORTANT! Before installing the hardware for your Zip ® Internal drive, insert the Owner’s Manual CD and click the button that says “Watch Installation Video” to give you an overview of the installation process.
T able o f Contents Installation Guide Getting Started ................................................................................ 4 Identifying the IDE Configuration ................................................. 6 Installing the Zip ® drive as the Slave Device .
1 2 3 W elcome to Zip ® Driv e! Zip ® Internal ATAPI drive offers you everything a standard Zip ® drive has with the ease of installing to an existing IDE channel on your computer! Here’s how to .
4 Installation Guide Getting Started M IMPORTANT! The Zip Internal drive uses the computer’s onboard IDE/ATA interface. See the User’s Guide section Understanding IDE Connections on pages 36 and 37 of this guide for important information. M Check system r equirements.
5 Installation Guide W atch the instructional video. Before installing the hardware for your Zip ® Internal drive, insert the Owner’s Manual CD and click the button that says “Watch Installation Video” to give you an overview of the installation process.
6 Installation Guide Identifying the computer’ s IDE configur ation IDE/ATAPI devices can be connected to your computer in different configurations. The following illustrations are examples of ways the IDE/ ATAPI devices may be connected to your computer.
7 Installation Guide Follow these instructions if you were unable to identify your computer’ s IDE configuration fr om the illustrations on the previous page: Locate the IDE channels using the CD drive From the back of the CD drive in your computer, follow the flat, wide cable to where it connects to the large main board, or motherboard.
8 Installation Guide Possible IDE channel locations There are usually two IDE channels, called the primary and secondary IDE channel, which are either side-by-side or end-to-end as shown in the illustrations below.
9 Installation Guide Determining your computer’ s configuration Once you have located the IDE channels, determine the configuration of the IDE/ATAPI devices that are connected to your computer. Steps 2a through 2c show some possible ways that your computer might be configured.
10 Installation Guide If the CD drive and hard drive ar e on dif ferent IDE channels... Follow the IDE interface cable to find out if the CD drive is the only device connected to the secondary IDE channel. If it is, see Installing the Zip Drive as the Slave Device starting on page 11 of this manual for instructions on installing your Zip ® drive.
11 Installation Guide Installing the Zip ® driv e as the slave , or second de vice M IMPORTANT! The Zip ® Internal drive uses the computer’s onboard IDE/ATA interface. If you are not familiar with how devices connect to the IDE interface, please see Understanding IDE Connections section on pages 36 and 37.
12 Installation Guide 3 1/2” drive bays ONL Y . To install your Zip ® drive in a 3 1/2” drive bay, remove the mounting screws as illustrated and slide the drive out of the sled. Check mounting requir ements. Y our drive bay may r equire side rails.
13 Installation Guide Slide the Zip ® drive into the drive bay . M NOTE: If it makes it easier to connect cables on your computer, you can secure the Zip ® drive in the drive bay now. (See step 9 for instructions on securing the drive.) M Remove the IDE Interface cable that is currently connected to your CD drive.
14 Installation Guide V erify that the jumper on your CD drive is set to “Master .” In order for the CD drive and Zip ® drive to work together properly, ensure that the jumper on the CD drive is set to the “master” setting. A chart indicating the jumper setting should be located on the CD drive.
15 Installation Guide Connect an internal computer power supply cable to the Zip ® drive. M NOTE: If the computer does not have a spare power supply cable, use the power Y-cable provided. Disconnect the power from the CD drive or another device (do not disconnect the power to the hard drive) and connect the power Y-cable.
16 Installation Guide Check the following items befor e replacing the computer cover: PIN 1 on the IDE interface cable matches the PIN 1 connector on your Zip ® Internal drive. The IDE interface cable is securely connected to all pins on your Zip ® drive.
17 Installation Guide Installing the Zip ® driv e as the only de vice on the secondary IDE channel M IMPORTANT! The Zip ® Internal drive uses the computer’s onboard IDE/ATA interface. If you are not familiar with how devices connect to the IDE interface, please see Understanding IDE Connections on pages 36 and 37.
18 Installation Guide 3 1/2” drive bays ONL Y . To install your Zip ® drive in a 3 1/2” drive bay, remove the mounting screws as illustrated and slide the drive out of the sled. Check mounting requir ements. Y our drive bay may r equire side rails.
19 Installation Guide Slide the Zip ® drive into the drive bay . M NOTE: If it makes it easier to connect cables on your computer, you can secure the Zip ® drive in the drive bay now. (See step 9 for instructions on securing the drive.) M Locate the data cable that comes packaged with the Zip ® drive.
20 Installation Guide Connect the data cable to the secondary IDE channel on the motherboar d. (Be sure PIN 1 on the cable is connected to PIN 1 on the motherboard.) PIN 1 to PIN 1 Connect the other end of the data cable to the Zip ® drive. CAUTION Make sure PIN 1 on the cable connects to PIN 1 on the Zip ® Internal drive.
21 Installation Guide Connect an internal computer power supply cable to your Zip ® drive. M NOTE: If the computer does not have a spare power supply cable, use the power Y-cable provided. Disconnect the power from the CD drive or another device (do not disconnect the power to the hard drive) and connect the power Y-cable.
22 Installation Guide Check the following items befor e replacing the computer cover: PIN 1 on the IDE interface cable matches the PIN 1 connector on your Zip ® Internal drive and the motherboard. The IDE interface cable is securely connected to all pins on your Zip ® drive.
23 Installation Guide Installing the IomegaW are ™ So ftw are Insert the IomegaW are ™ CD into the computer’ s CD drive. M No CD Drive? If you want to install the Zip ® Internal drive on a computer that does not have a CD drive, you can download Iomega software from the I nternet.
24 Installation Guide Additional instructions f or your s y stem... Windows 95/98 Users Your Zip ® drive and IomegaWare ™ software should now be ready to use. Open My Computer to see if you have an icon for your Zip drive. Windows NT Users The Iomega installation software will try to install and update the necessary drivers on your system.
25 Installation Guide 11. Click the “Install” button. Windows NT will copy the driver file and add the Iomega Zip ® driver to the list of installed adapters found by the system. 12. Click the “Close” button and exit Windows NT Setup. 13. Click “OK” at the message box and reboot the system.
26 Installation Guide 4. Double click the Diskette icon, and follow the screen instructions. 5. To install software drivers for your Zip ® drive, run setup.exe from the install diskette you created. Congratulations! When the softwar e installation is complete, your Zip ® drive will be ready to use.
27 User’ s Guide Oper ating Y our Zip ® Driv e To use the Zip ® drive, insert a 250MB* Zip disk, then select the drive letter assigned to the Zip drive in My Computer (Windows 95/98; Windows NT 4.
28 User’ s Guide Ejecting Zip ® Disks Windows 95/98 systems: Push the disk eject button or use the Iomega software eject command. Windows NT systems: Use the Iomega software eject command. Windows 3.1 systems: Push the disk eject button. When your Zip ® drive is not in use, remove the disk from the drive.
29 User’ s Guide Compatibility with 100MB Zip ® Disk s The 250MB Zip ® drive features backward compatibility that allows you to read and write to 100MB Zip disks. However, because of the higher capacity of the 250MB Zip drive, performance when writing to a 100MB Zip disk is significantly reduced.
30 User’ s Guide Zip ® Tips Here ar e a few tips you’ll want to keep in mind to care for your Zip ® drive and disks! Always turn on power to your computer before inserting a Zip ® disk. CAUTION If a disk is inserted without the power on, and power is then applied, it could damage the drive.
31 User’ s Guide IomegaW ar e ™ So ftwar e The IomegaWare software package* includes tools and programs designed to help you take advantage of all the features of your Zip ® drive. You can use Iomega software to format, copy, and protect your Zip disks, back up your hard drive, set options for your Zip drive, and more.
32 User’ s Guide Drive Shortcuts Create Drive Shortcuts puts a Zip ® drive icon directly on your Desktop and in the “WindowsSendTo” and “My Documents” folders, making it easier to use your Zip drive.
33 User’ s Guide U sing Zip ® Disks Use only genuine 250MB* or 100MB* Zip ® disks with your Zip drive. This section describes just some of the things you can do with Zip disks. The help files contained in your IomegaWare ™ software package include additional information on using Zip disks.
34 User’ s Guide Installing Applications to Zip ® Disk s On a PC, some applications and games will only install to, or run from, a fixed disk such as a hard drive. In order to install these programs to a Zip ® disk, use the Make Nonremovable tool in your IomegaWare TM software package to make the Zip disk appear as a fixed disk to the system.
35 User’ s Guide Read/Write Pr otecting Zip ® Disk s IomegaWare TM software includes a special read/write protect feature that allows you to: • Write Protect a disk through software instead of with a mechanical write protect switch. • Write Protect a disk and assign a password that must be used to remove the write protect.
36 User’ s Guide Under standing IDE/A T API Connections What is IDE? IDE (Integrated Drive Electronics) is the built-in system a PC computer uses to connect drives to the computer. You may have also heard it called ATA (Advanced Technology Attachment)—they mean the same thing.
37 User’ s Guide Jumper block Slave (Drive 1) (Factory Setting ) Master (Drive 0) Cable Select Reserved (do not use) Zip Inter nal drive Slave (Drive 1) Use this setting if you’re connecting the Zip ® Internal drive on the same cable as your CD drive or another ATAPI device that is configured as the master.
T roubleshooting 38 T roubleshooting If you encounter a problem while installing or using your Zip ® drive, check this section for help. CAUTION T o avoid damage to your computer , disconnect all electrical connections before connecting or disconnecting cables.
T roubleshooting 39 If you are unable to disable BIOS support for the Zip ® drive in the CMOS setup and the Zip Internal drive does not appear on the system, the computer may have an incompatible BIOS that does not correctly understand removable internal drives.
T roubleshooting 40 Computer fails to boot correctly or hangs while booting after the Zip ® Internal drive is installed. Make sure BIOS support for the Zip ® Internal drive is disabled in the computer’s CMOS setup. Note that this may require turning off autodetection for the Zip Internal drive.
T roubleshooting 41 You want to change the drive letter assigned to the Zip ® drive. Windows 95/98 Users: If your computer is running Windows 95/98, you can change drive letters as desired for any of your removable drives (including your Zip ® drive and CD drive) by running the Guest program (guest9x.
T roubleshooting 42 You can’t change the drive letter assigned to your Zip ® drive. Make sure BIOS support for the Zip ® Internal drive is disabled in the computer’s CMOS setup. This may require turning off autodetection for the Zip Internal drive.
T roubleshooting 43 You want to use Windows 95/98 DOS mode with your Zip ® drive. M NOTE: This section describes how to switch in and out of the MS-DOS mode which is a start option for Windows 95/98. It does not apply to the DOS box (or window) that opens when you double click the MS-DOS Prompt icon within Windows 95/98.
How T o Get Help 44 Ho w to Get Help Iomega’s goal is to provide state-of-the-art support for its customers. Over time, our support options and pricing policies may change in light of evolving technology and global changes across the computer industry.
How T o Get Help 45 Automated FAX-back Help: (801) 778-5763 (U.S. & Canada) Our FAX-back automated help system allows you to use any touch-tone phone to instantly retrieve detailed support information to your FAX machine.
How T o Get Help 46 Return or Repair For information on returning your Zip ® drive or other Iomega product for warranty service (or repair after the warranty period), please call the Iomega Customer Satisfaction Hotline at 1-888-4-IOMEGA (1-888-446-6342).
Regulatory Inf ormation Product Name: Iomega Zip ® Internal ATAPI 250MB drive Model Number: Z250ATAPI FCC (United States) The computer equipment described in this guide generates and uses radio frequency (RF) energy.
Visit our web site! h ttp://www .i om ega.com • Fr ee softwar e updates* an d cool free so ftware • Onlin e Customer Support • Pur chase Iom ega produ cts at BuyI t Online • Pr oduct inf orm a.
デバイスIomega 03798300の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Iomega 03798300をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIomega 03798300の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Iomega 03798300の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Iomega 03798300で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Iomega 03798300を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIomega 03798300の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Iomega 03798300に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIomega 03798300デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。