IPSOメーカーT30の使用説明書/サービス説明書
ページ先へ移動 of 21
4-08-43R5 August 201 1 Refer to Installation ma nual for full instructions. T30 and T45 T umbler s START 25 C H IG H T EM P M ED T E M P L O W T E M P NO H E A T 1 2 3 S E L E C T T E M P I N S E R T .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT © Published by pe rmission of the cop yright owner . All rights reserved. No part of the cont ents of this book may be reproduced or transmitted in any form or by any means without the expressed writte n consent of the publisher .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 2 4-08-43 T umbler s – T30 and T45 Introduction Model Identification Includes models with the follow ing control suffixes: T4.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 3 TMB1974N 1 Serial Plate 1 Conversion T able Multiply By T o Obtain Multiply By T o Obtain Btu 0.252 kCal Pounds/sq. inch 0.06895 Bars Btu 1055 Joules Pounds/sq.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4 4-08-43 S pecifications and Dimensions N/A = Not Applicable Specific ations T30 T45 Noise level meas ured during operation a t operator position of 3.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 5 Cabinet Dimensions NOTE: T o meet ADA compliance, install a 4 inch (102 mm) riser on T30 models only . TMB2332N TMB2332N C E F H J B D G I A M o d e l s ABCD E T30 28 in.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 6 4-08-43 Exhaust Outlet Locations TMB1969N TMB1969N B C A Models Rear Exhaust Diamet er A B C T30 Elliptical Fits 8 in. (203 mm) 36.54 in. (928 mm) 4.25 in.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 7 Gas Connection Locations TMB1970N 1 1/2 in. NPT TMB1970N A B C 1 Models Gas Connection AB C T30 Non-CE and Non-Australian 75.20 in. (1910 mm) 1.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 8 4-08-43 Electrical Connection Locations TMB1971N TMB1971N A B E D C GAS AND STEAM ELECTRIC Models Electric Service Gas and Ste am Models Electric Models ABCD E T30 59 in.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 9 Steam Connection Locations NOTE: All connections use 3/4 inch NPT pipe. TMB1972N C D A B A B Models Inlet O utlet AC B D T30 (Upper) 73.93 in.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 10 4-08-43 Inst allation Pre-Inst allation Inspection Upon delivery , visually insp ect the crate, carton and parts for any visible shipping damage.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 11 Figure 1 TMB21 10N NOTE: Shaded areas indic ate adjacent structure. 1 0.5 in. (13 mm) recommended between machines for removal or installation.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 12 4-08-43 Exhaust Requirement s Layout Whenever possible, install tumblers along an outside wall where duct length can be kept to a minimum, and make-up air can be easily accessed.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 13 IMPOR T ANT : For best performance provide an individual exhaust duct for each tumbler . Do not install a hot water heater in a room containing tumblers.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 14 4-08-43 NOTE: Do not install wire mesh or scr een in exhaust duct opening to avoid lint build-up or impacting proper discharge of air fr om tumblers.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 15 The vent collector system must be designed so the static back pressure measured 12 inches (305 mm) from the exhaust outlet does not exceed the maximum allowable pressure specified on the installation s ticker on the rear of tumbler .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 16 4-08-43 Figure 4 TMB2019N 1 NOTE: Wher e the exhaust duct pierces a combustible wall or ce iling, the opening MUST be sized per local codes.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 17 Figure 5 TMB2018N 1 NOTE: Wher e the exhaust duct pierces a combustible wall or ce iling, the opening MUST be sized per local codes.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 18 4-08-43 Electrical Requirements for Gas and S team Models Refer to T able 4 and Ta b l e 5 . NOTE: Minimum wire sizes ar e obtained from Canadian Electrical Code for 75°C Conductors and are intended for use as a guideline only .
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 4-08-43 19 For T45 Gas Models (For T otal Machine): Serial Plate Vo l t a g e T erminal Block Connect.
© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT T umblers – T30 and T45 20 4-08-43 Electrical Requirement s for Electric Models Refer to T able 6 . NOTE: Minimum wire sizes ar e obtained from Canadian Electrical Code for 75°C Conductors and are intended for use as a guideline only .
デバイスIPSO T30の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
IPSO T30をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはIPSO T30の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。IPSO T30の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。IPSO T30で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
IPSO T30を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はIPSO T30の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、IPSO T30に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちIPSO T30デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。