JAIメーカーCV-L105の使用説明書/サービス説明書
ページ先へ移動 of 22
3CCD High Speed Color Line Scan Camera CV -L105 Operation Manual Camera: Revision A Manual: Version 1.1 CV-L105manJan9.doc JPT 9- 01-03.
CV-L105 - 1 - T able of Contents 1. General ........................................................................................................ 2 2. Standard Co mposition ...........................................................................
CV-L105 1. Gener al The CV-L105 is a high-speed 3CCD color line sc an camera with 2048 pixels resolution. It features digital LVDS RGB output with 30 MHz pixel rate, allowing l ine rate up to 14285 lines/second. An exposure control function facilitates constant exposure time, independent of the scan rate.
CV-L105 - 3 - 5. Pin Assignment 5.1. 68-pin Digital in terface connector (Digital video, control signals, tr igger input) Fig. 2. 68-pin digital int erface.
CV-L105 5.2. 6-pin Hirose connector (Power) Fig. 3. 6-pin Hirose . (Seen from camera rear.) Pin no. Signal Remarks 1 NC 2 NC 3 GND Power GND 4 GND Power GND 5 NC 6 +12V DC in + Power in The camera connector part number is Hi rose H10A-7R-6P. (Male). The mating connector to use on the cable side is Hirose HR10A-7P-6S 5.
CV-L105 5.4. Input and Output Circuits Video outputs, timing outputs, trigger input an d control inputs are found on the 68 pin LVDS connector. 5.4.1. Video output The digital EIA-644 LVDS output is c.
CV-L105 5.4.2. Trigger input The camera is triggered by an EIA-644 LVDS input signal pai r. (+EXT TRIG in/ -EXT TRIG in (on pin #19 and pin #53)). Depending on the configuration of t he camera, this input can prov ide operation in 4 modes: Internal Trigger.
CV-L105 6. F unctions and Oper ations 6.1. Principle of operation A line scan camera works according to the same principle as a fax ma chine, also sometimes referred to as a “push broom” oper ation.
CV-L105 - 8 - Horizontal Resolution Vertical Resolution Encode r CV-L105 PC with Frame Fig. 10. Specifying an e ncoder. Example of a camera set-up, with a n encoder.
CV-L105 6.2. Trigger modes Internal Trigger. Scan mode. The camera will operate continuously with its internal trigger. LEN Data out Exposure Exposur e t i me = SCAN val ue LEN Data out Exposure Exposur e t i me = SCAN val ue The exposure is equal to the scanning time set by the SCAN parameter via RS-232C only.
CV-L105 6.2.1. Internal T rigger. Scan mode. In this mode, the camera does no t require an EXT TRIG signal to be issued to the c amera. The line rate (scan rate) is generated inside the camera. The camera will operate continuously with its internal trigger.
CV-L105 6.2.2. Internal Trigger. Shutter mode. In this mode, the camera does no t require an EXT TRIG signal to be issued to the c amera. The line rate (scan rate) is generated inside the camera. The camera will operate continuously with its internal trigger.
CV-L105 6.2.3. External Trigger . Scan mode. In this mode, the camera requires an EXT TRIG signal to be issued to the camera. The trigger signal is typical taken from an e ncoder. The exposure time is equal to the trigger interval. On the EXT TRIG input positive going edge the ongoin g integration peri od is terminated and charge is read out.
CV-L105 6.2.4. External Trigger. Shutter mode. In this mode, the camera requires an EXT TRIG signal to be issued to the camera. The trigger signal is typical taken from an e ncoder. The sca nning time is equal to the trigger interval. The exposure time is equal to the trigger low period (pulse wid th).
CV-L105 6.3. Other functions 6.3.1. Binnig Binning is a function where the signal from t wo neighbour pixels are ad ded and read out as a single pixel. The sensitivity will be double, but the resolution will be t he half. The binning function has no influence on the internal scan rate and shutter setting.
CV-L105 7. Configuring the Camer a All configuration of the CV-L105 ca mera is done via the RS -232C port, which is factory setting. Binning and pixel rate settings can also be cont ro lled by TTL signals into the interf ace connector or internal jumpers.
CV-L105 - 16 - Fig. 18. Shutter window 7.1.1. Clock Select With Clock Select two speeds can be selected, 15 MHz or 30 MHz . The 15 MHz operation will limit the maximum li ne rate (scan rate) to 7 172 Hz. It is recommended when a cable length of more th an 20 metres is used or in applications where high RFI fields may be experienced.
CV-L105 7.1.6. Gain and offset adjustment Fig. 19. Gain and Offset window The individual gain and offset setting of each co lor is possible. This is required for adapting the white balance temperature for the 4 user config uration are as. For the factory default this setting has no function.
CV-L105 7.2. Configuration via I/ F connector and jumpers The binning function, pixel rate and RS-232C function can b e controlled by TTL inputs on the 68pin Hirose interface connector and with jumper settings. Below table describe the possible states of these inputs.
CV-L105 - 19 - 8. External Appear ance and Dimensions Fig. 22. Outlines.
CV-L105 9. Specifications 9.1. Specifications table Specifications CV-L105 Scanning system Line scan Pixel clock 15 or 30 MHz, user selectable Line rate (scan rate) Up to 7172 lines/sec at 15 MHz, and up to 14285 lines/sec at 30 MHz CCD sensor 3 x 2048 line scan sensors mounted on an RGB prism Sensing area 28.
CV-L105 10. Users Record Camera type: CV-L105 Revision: (Revision A) Serial No. …………….. Software version. …………….. For camera revision hi story, please contact your local JAI d istributor.
デバイスJAI CV-L105の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JAI CV-L105をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJAI CV-L105の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JAI CV-L105の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JAI CV-L105で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JAI CV-L105を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJAI CV-L105の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JAI CV-L105に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJAI CV-L105デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。