JAIメーカーCV-M50の使用説明書/サービス説明書
ページ先へ移動 of 24
Opera tion Manual Industrial Monochrome CCD Camera (Rev.F) CV -M50.
CV -M50 DECL ARA TION OF CONFORMIT Y AS DE FINED B Y THE C O UNC IL D IRE C T I V E 89/336/EEC E MC (E LECTR O MAG N E TIC C OMP A TI B I LITY ) WE HE R E WITH DECLAR E THA T TH IS PRODUCT C OM PLI E S WITH THE FOLL OWI NG PR OVISIONS APPL YI NG T O IT .
- 2 - CV -M50 T able of Contents T able of Contents .............................................................................................................. ......................... 2 1 . General ................................................
- 3 - CV -M50 1. General The CV -M50 is a monochrome 1/2" CCD camera designed for automated imaging applications featuring high performance and unique functions within a uniform and compact housing. The high-speed shutter function and asynchronous random trigger function allow the camera to capture high quality images of fast moving objects.
- 4 - CV -M50 4. Locations and F unctions 1 1/2" interline transfer CCD sensor. 2 Lens mount of C-mount type. *1) 3 BNC connector for video output. 4 Switch block SW1 for shutter speed and function modes setting. 5 6-pin multi connector for WEN and EEN output external trigger input.
- 5 - CV -M50 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) T ype: HR10A-10R-12PB-01 (Hirose) male Seen from rear. Notes: *1 ) Signals on pin no. 6, 7 and 9 can be changed by jumper setting. See “7.3. Jumper Settings” for more information.
- 6 - CV -M50 6. F unctions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0V p-p +/- 2.0V at the input with the 75 Ohm termination ON.
- 7 - CV -M50 T o use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1,2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector.
- 8 - CV -M50 The EEN pulse indicates the exposure time. The EEN pulse is output from pin 2 of the 6-pin multi connector. The signal level is 4.0 Vp-p from a 75 Ohm source. The WEN pulse indicates the time period of the effective video signal output and is useful for the timing and interfacing of external devices such as frame grabbers.
- 9 - CV -M50 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext.
- 10 - CV -M50 6.3.3. Star t/Stop T rigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext.
- 11 - CV -M50 Cautions in the Star t/Stop T rigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max., when the falling edge of ext.
- 12 - CV -M50 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext.
- 13 - CV -M50 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . CCIR: 1/25 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext.
- 14 - CV -M50 7. Mode Setting Caution on Mode Setting. Before making any mode or jumper setting turn the po wer OF F . 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. 7.1.2. T able for SW 1 Setting 7.
- 15 - CV -M50 7.1.4. Ext. T rigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1- 3 are for selecting the shutter speed. The range is from OFF to 1/10,000 second in 8 steps. For each external trigger pulse, the camera will make an exposure with the selected shutter speed.
- 16 - CV -M50 7.3. Jumper Settings Caution on Jumper Setting. Before making any mode or jumper setting turn the po wer OF F . Jumpers for mode setting are found on the boards PK8054 & PK8057. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal.
- 17 - CV -M50 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. T o remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8054 Side B 7.
- 18 - CV -M50 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8056 board while measuring their levels at the video output connector.
- 19 - CV -M50 9. External Appearance Unit : mm (inches).
- 20 - CV -M50 10. Specifications Scanning system CCIR 625 lines EIA 525 lines 25 frames/sec. 30 frames/sec. CCD sensor Monochrome 1/2" Hyper HAD IT CCD Sensing area 6.6 mm ( h) x 4.8 mm ( v) Effective pixels 752 (h) x 582 (v) 768 (h) x 494 (v) Elements in video output 737 (h) x 575 (v) 758 (h) x 486 (v) Cell size 8.
- 21 - CV -M50 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components.
- 22 - CV -M50 12. User’s R ecord Camera type: CV -M50 Scanning system: EIA/CCIR Revision: (Revision F) Serial No. ................. Users Mode Settings Users Modifications This manual can be downloaded from: www.
JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Y okohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.
デバイスJAI CV-M50の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JAI CV-M50をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJAI CV-M50の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JAI CV-M50の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JAI CV-M50で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JAI CV-M50を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJAI CV-M50の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JAI CV-M50に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJAI CV-M50デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。