JBLメーカーA3000GTIの使用説明書/サービス説明書
ページ先へ移動 of 12
car audio pow er amplifier owner’ s manual THANK Y OU for purchasing a JBL A6000GT i or A3000GT i amplifier . For warranty support, please register your purchase at www.jbl.com. Select Car Audio, then click on Support, and then click on Product Registration.
INST ALLA TION W ARNING: Playing loud music in an automobile can hinder your ability to hear traffic and permanently damage your hearing. We recommend listening at low or moderate levels while driving your car . JBL accepts no liability for hearing loss, bodily injury or property damage resulting from the use or misuse of this product.
DESIGNING A SPEAKER SY STEM FOR THE GTI AMPLIFIER NOTE: Although the JBL A6000GT i or A3000GT i amplifier will drive a system made up of any subwoofers, we recommend using JBL GT i subwoofers with GT i amplifiers.
4 SUPPL YING POWER TO THE GTI AMPLIFIER POWER IN IS POWER OUT In order to get full power out of your amplifier , you must provide full power to your amplifier . That’ s a basic rule of physics. The A6000GT i amplifier can draw nearly 800 amperes when reproducing sine waves at full output.
5 MAKING THE CONNECTIONS POWER CONNECTIONS Use 0-gauge cable to connect the amplifier’ s GND – terminal directly to the vehicle’ s chassis (see Figure 5). Scrape off all paint from the metal area for a good, clean ground connection. Make sure the ground wire is as short as possible and is connected to metal on the vehicle’ s body.
6 MAKING THE CONNECTIONS A6000GTi SPEAKER CONNECTIONS The A6000GT i is a 2-channel amplifier designed to drive subwoofers only . The left and right input signals are com- bined inside the amplifier to provide a mono output signal, no matter which output mode is selected.
7 MAKING THE CONNECTIONS A3000GTI SPEAKER CONNECTIONS Included below are three application diagrams that will help you plan your A3000GT i installation. Figures 10 through 12 show how to configure the JBL A3000GT i amplifier for bridged-mono, parallel-mono and 2-channel operation (also see Setting Up the GT i Amplifier).
8 SETTING UP THE GTI AMPLIFIER SETTING INPUT SENSITIVITY NOTE: Y ou can use the supplied REMOTE LEVEL control to fine-tune the input sensitivity or to adjust the level of the bass according to the program material after the amplifier’ s LEVEL control has been set properly .
9 SETTING UP THE GTI AMPLIFIER REPLACING THE FUSE OR NEON TUBES The JBL A6000/A3000GT i amplifier is equipped with an internal fuse, a 20-inch neon tube and two 6-inch neon tubes.
10 SETTING UP THE GTI AMPLIFIER 7. Using a T -15 screwdriver , remove the two T orx-head screws on the display board and set them aside (see Figure 16 below). Disconnect the ribbon cable from display board. 8. Using a T -15 screwdriver , remove the 16 T orx-head screws on the perforated shield and set them aside (see Figure 16).
11 TROUBLESHOOTING SYMPTOM LIKEL Y CA USE SOLUTION No audio No voltage at power Check BA TT+, REMOTE and (Power LED is off) or remote terminal GND – terminals with VOM for blown fuse or poor connect.
Declaration of Conf or mity We, Har man Consumer Group Inter national 2, route de T ours 72500 Chateau-du-Loir Fr ance declare in own responsibility that the products described in this owner’s man u.
デバイスJBL A3000GTIの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
JBL A3000GTIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJBL A3000GTIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JBL A3000GTIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JBL A3000GTIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JBL A3000GTIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJBL A3000GTIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JBL A3000GTIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJBL A3000GTIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。