JeepメーカーLiberty (2004)の使用説明書/サービス説明書
ページ先へ移動 of 374
T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................. 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ...........
I n f o r m a t i o n P r o v i d e d b y :.
INTRODUCTION CONTENTS m Introduction ........................... 4 ▫ Roll Over W arning ..................... 4 m How T o Use This Manual .................. 6 m W arnings And Cautions ................... 7 m V ehicle Identification Number ..........
INTRODUCTION Thank you for selecting a Jeep t Liberty and welcome to our worldwide family . This is a specialized utility vehicle designed for both on-road and off-road use. It can go places and perform tasks for which conventional two-wheel drive vehicles were not intended.
and the narrower track, if this vehicle is out of control it may roll over when some other vehicles may not. Do not attempt sharp turns or abrupt maneuvers or other unsafe driving actions that can cause loss of vehicle control. Failure to operate this vehicle safely may result in an accident, roll over of the vehicle, and severe or fatal injury .
NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold so that the new owner will be aware of all safety warnings.
W ARNINGS AND CAUTIONS This manual contains W ARNINGS against operating procedur es which could result in an accident or bodily injury . It also contains CAUTIONS against procedur es which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
VEHICLE MODIFICA TIONS / AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS m A W ord About Y our Keys .................. 1 2 ▫ Ignition Key .......................... 1 2 ▫ Key-In-Ignition Reminder ................ 1 4 m Sentry Key Immobilizer System — If Equipped .
▫ T o Unlock The Doors ................... 2 3 ▫ T o Lock The Doors ..................... 2 4 ▫ T o Unlatch The Swing Gate Flip-Up W indow . . 24 ▫ Panic Alarm .......................... 2 5 ▫ T o Use The Panic Alarm ................. 2 5 ▫ T o Program Additional T ransmitters .
▫ Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags .......... 4 6 ▫ Child Restraint ........................ 5 8 m Engine Break-In Recommendations ........... 6 8 m Safety T ips ............................ 6 8 ▫ Exhaust Gas .
A WORD ABOUT YOUR KEYS The keys for your new vehicle are enclosed in a plastic bag with the key code number on it. If you received your keys without the bag, ask your dealer to give you the number . The key code can also be obtained by the dealer from your vehicle invoice.
T o remove the ignition key on models with an automatic transmission, place the gearshift lever in P (Park), turn the ignition key to LOCK and remove the key . T o remove the ignition key on models with a manual transmission, depress and hold the key release button, turn the ignition key to LOCK and remove the key .
Key-In-Ignition Reminder If you open the driver’s door and the key is fully inserted in the ignition switch, a chime will sound to remind you to remove the key . SENTR Y KEY IMMOBILIZER SYSTEM — IF EQUIPPED The Sentry Key Immobilizer System (SKIS) prevents unauthorized operation of the vehicle by disabling the engine.
NOTE: • The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and loss of security protection.
consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed. NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer . Customer Key Programming Y ou can program new keys to the system if you have two valid keys by doing the following: 1.
2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. STEERING WHEEL LOCK — IF EQUIPPED Y our vehicle may be equipped with a passive steering wheel lock (manual transmission only).
DOORS AND DOOR LOCKS The vacuum fluor escent (VF) display located in the odometer area displays the word “door” as an indication of a door ajar or door not completely closed.
If the trip/reset button is pressed while the VF warnings are being displayed, the VF display will revert back to only displaying the odometer/trip odometer mileage. Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle.
W ARNING! • For personal security , and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock. Ther efore, make sure the keys are not inside the vehicle before closing the door .
Child Protection Locks The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle. Push the lever down to disengage the child protection locks.
REMOTE KEYLESS ENTR Y This system allows you to lock or unlock the doors or open the swing gate flip-up window from distances of 23–50 feet (7–15 meters) using a transmitter . Y ou don’t have to point the transmitter at the vehicle to activate the system.
2. Continue to hold the 9 Lock 9 button, wait at least 4 but no longer than 10 seconds, then press the “Rear Release” button. 3. Release both buttons.
NOTE: The transmitter can be programmed to unlatch the flip-up window immediately upon activation of the “Rear Release” button (without pressing and holding) (within 23–50 feet (7–15 meters) of the vehicle) by per- forming the following procedur e: 1.
T o Program Additional T ransmitters NOTE: If vehicle is equipped with the optional Elec- tronic V ehicle Information Center (EVIC) in the overhead console, the transmitters may also be programmed through the EVIC display . For additional information, refer to “Overhead Console — If Equipped” in Section 3.
2. This device must accept any interference that may be received, including interference that may cause undes- ired operation. If your Remote Keyless Entry fails to operate from a normal distance, check for these two conditions: 1. W eak batteries in transmitter .
SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors, swing gate, swing gate flip-up window , and ignition for unautho- rized operation. When the alarm is activated, the system provides both audible and visual signals. The horn, headlights, and tail lights will sound/flash r epeatedly for three minutes.
NOTE: On vehicles equipped with Remote Keyless Entry (RKE), there will not be a door lock cylinder on the front passenger door , rear doors, or rear swing gate. Therefor e, you will be unable to disarm the system with a manual unlock of the passenger or rear doors.
T o open the swing gate, pull the gate handle to its first detent to open just the flip-up window . Pull the handle to its second detent (all the way) to open both the flip-up window and swing gate. W ARNING! T o avoid injury stand back when opening. Glass will automatically rise.
NOTE: If vehicle is equipped with the optional Elec- tronic V ehicle Information Center (EVIC) in the overhead console, all warnings including “door”, “GA TE”, “GLASS”, and “LOW ASH” will only be displayed in the EVIC display (not in the instrument cluster).
If the trip/reset button is pressed while the VF warnings are being displayed, the VF display will revert back to only displaying the odometer/trip odometer mileage. NOTE: Close swing gate before flip-up window . CAUTION! Do not press on rear wiper blade when closing swing gate, as damage to the blade will result.
Auto Down Feature — If Equipped The driver’s and passenger’s front window switches have an auto down featur e. Pr ess the window switch past the detent, release, and the window will go down auto- matically . T o open the window part way , press the window switch part way and release it when you want the window to stop.
Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Buckle up even though you are an excellent driver , even on short trips. Someone on the road may be a poor driver and cause a collision which includes you. This can happen far away from home or on your own street. Research has shown that seat belts save lives, and they can reduce the seriousness of injuries in a collision.
W ARNING! • W earing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body . These are the strongest parts of your body and can take the forces of a collision the best. W earing your belt in the wrong place could make your injuries in a collision much worse.
3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” THINGS TO KNOW BEFORE ST ARTING YOUR VEHICLE 37 2 I n f o r m a t i o n P r o v i d e d b y.
W ARNING! A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. A belt that is too loose will not protect you as well.
W ARNING! A lap belt worn too high can increase the risk of injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdo- men. Always wear the lap part of your seat belt as low as possible and keep it snug.
6. T o release the belt, push the red button marked PRESS on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow it to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
W ARNING! Position the shoulder belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.
When T o Use The Automatic Locking Mode Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. How T o Use The Automatic Locking Mode 1.
W ARNING! • After a vehicle collision, the driver and front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly . In addition, all seat belts should be checked for proper function.
Enhanced Driver Seat Belt Use Reminder System (BeltAlert) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the Enhanced W arning System (BeltAlert) will alert the driver to buckle their seat belt.
The Enhanced W arning System (BeltAlert) can be reacti- vated by repeating this procedure. NOTE: Although the Enhanced W arning System (BeltA- lert) has been deactivated, the Seat Belt W arning Light will continue to illuminate while the driver’s seat belt remains unfastened.
Driver And Front Passenger Supplemental Restraint Systems (SRS) — Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
This vehicle may also be equipped with window bags to protect the driver , front, and rear passengers sitting next to a window . If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
Along with the seat belts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger . W indow bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
Y ou should read the instructions provided with your child r estraint to make sure that you are using it pr operly . 2. All occupants should use their lap and shoulder belts properly . 3. The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate.
Airbag System Components The airbag system consists of the following: • Occupant Restraint Controller • Remote Acceleration Sensors • Airbag W arning Light • Driver Airbag • Passenger Airbag.
modify the rate of inflation based on the occupant size provided by the Occupant Classification Module. The ORC will not detect roll over , or rear impacts. The ORC monitors the readiness of the electronic parts of the system whenever the ignition switch is in the ST AR T or RUN positions.
not be able to pr operly approximate occupant size. Furthermore, the occupant size may appear to incr ease or decrease due to objects hanging on the seat, other passengers pushing on the seat, or objects lodged underneath the seat. If there is a rapid change in temperature or humidity , the OCS may not be able to properly approximate occupant size.
For almost all sizes of properly seated adults, the passen- ger frontal airbag will be enabled in the event of a collision. For small teenagers and some small adults, depending on size, the airbag may or may not be enabled in the event of a collision.
upper right side of the instrument panel separate and fold out of the way as the bags inflate to their full size. The bags fully inflate in about 50–70 milliseconds. This is about half of the time it takes to blink your eyes. The bags then quickly deflate while helping to restrain the driver and front passenger .
pressur e increase due to applied lap belt tension does not cause a small occupant to be classified as a larger occupant. • The Bladder Mat and Pressure Sensor are located beneath the seat cushion foam. The pressur e sensor sends a signal to the OCM.
• The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor .
Also, the fuel system will shut off immediately upon airbag deployment (gasoline models only). The ignition switch will need to be cycled (i.e. turn the ignition key from the ON position to the LOCK position) after ap- proximately 5 seconds in order to restart the vehicle.
W ARNING! • Y ou need proper knee impact protection in a collision. Do not mount or locate any aftermarket equipment on or behind the knee bolsters. • It is dangerous to try to repair any part of the airbag system yourself. Be sure to tell anyone who works on your vehicle that it has an airbag system.
W ARNING! In a collision, an unrestrained child, even a tiny baby , can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are. The child and others could be badly injured.
• Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. The manufacturer recommends that you try a child restraint in the vehicle seats where you will use it before you buy it.
• When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it fr om the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury .
Installing the LA TCH-Compatible Child Restraint System W e urge that you carefully follow the directions of the manufacturer when installing your child r estraint. Not all child r estraint systems will be installed as described her e. Again, carefully follow the installation instructions that were provided with the child restraint system.
In addition, there ar e tether strap anchorages behind each rear seating position located on the back of the seat. Many , but not all restraint systems will be equipped with separate straps on each side, with each having a hook or connector for attachment to the lower anchorage and a means of adjusting the tension in the strap.
the seat, removing slack in the straps according to the child restraint manufacturer’s instructions. W ARNING! Improper installation of a child restraint to the LA TCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed.
If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
W ARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not required for the engine in your new vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
• Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for a extended period.
Defrosters Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should feel the air directed against the windshield. Safety Checks Y ou Should Make Outside The V ehicle T ires Examine tires for excessive tread wear or uneven wear patterns.
UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS m Mirrors ............................... 7 5 ▫ Inside Day/Night Mirror ................. 7 5 ▫ Inside Automatic Dimming Mirror If Equipped .......................... 7 6 ▫ Outside Mirrors ..
▫ Head Restraints ....................... 9 2 ▫ Power Seat Adjuster — If Equipped ......... 9 3 ▫ 65/35 Split Folding Rear Seat .............. 9 4 ▫ Heated Seats — If Equipped .............. 9 7 m T o Open And Close The Hood ..............
m Electronic Speed Control .................. 1 0 8 ▫ T o Activate .......................... 1 0 8 ▫ T o Set At A Desired Speed ............... 1 0 9 ▫ T o Deactivate ........................ 1 0 9 ▫ T o Resume Speed ..................... 1 0 9 ▫ T o V ary The Speed Setting .
▫ Smoker’s Package — If Equipped .......... 1 3 6 m Cargo Area Features ..................... 1 3 7 ▫ Cargo Light ......................... 1 3 7 ▫ Retractable Cargo Area Cover — If Equipped ....................... 1 3 7 ▫ Cargo T ie-Down Hooks .
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window . A two-point pivot system allows for horizontal and vertical adjustment of the mirror . The mirror should be adjusted while set in the day position (toward windshield).
Inside Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. Y ou can turn the feature on or off by pressing the button at the base of the mirror . A light in the button will indicate when the dimming feature is activated.
W ARNING! V ehicles and other objects seen in the right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side mirror could cause you to collide with another vehicle or other objects. Use your inside mirror when judging the size or distance of a vehicle seen in the right side mirror .
Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Illuminated V anity Mirrors — If Equipped An illuminated vanity mirror is on the sun visor .
phone’s audio is transmitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call.
cellular phone has a dif ferent pr ofile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversa- tion will be played over your vehicle’s stereo system.
pin number . Y ou will not need to remember this pin number after the initial registration process. • The UConnect™ system will then pr ompt you to begin the cellular phone pairing process on your cellular phone. Please see your cellular phone user’s manual for instructions on how to complete this step.
Add Names to Y our UConnect™ Phonebook • Press the “Phone” button to begin. • After the 9 Ready 9 prompt, say 9 Phonebook New En- try 9 . • When prompted, say the name of the new entry . • Next, enter the number designation (e.g. “Home”, “W ork”, “Mobile”, or “Pager”).
Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook. For example, the entry John Doe may have a mobile and a home number , but you can add John Doe’s work number later through phonebook edit. Delete Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin.
• The UConnect™ system will play the names of all the phonebook entries. • T o call one of the names in the list, press the ’V oice Recognition’ button during the playing of the desired name and say 9 Call 9 . • The UConnect™ system will then prompt you as to number designation you wish to call.
Making a Second Call while Current Call in Progress T o make a second call while you are currently in a call, press the ’V oice Recognition’ button and say 9 Dial 9 or 9 Call 9 followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progr ess.
Phone Redial • Press the ’Phone’ button to begin. • After the 9 Ready 9 prompt, say 9 Redial 9 . • The UConnect™ system will call the last number that was dialed on your cellular phone. This may not be the last number dialed by your UConnect™ system.
If you would like to connect or disconnect the Blue- tooth™ connection between a paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin.
pin. This method can also be used in instances wher e you are pressing a number on your keypad to navigate through a menu structur e or to enter a number for a pager . Barge In - Overriding Prompts The ’V oice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately .
Low Signal, Battery Strength, and Roam Notification The UConnect™ system will provide notification to inform you if your cellular phone is in roaming status, has low signal strength, or has a low battery when you are trying to place a phone call.
T owing Assistance If you need towing assistance, say 9 Dial T owing Assis- tance 9 or 9 Call T owing Assistance 9 . Please refer to the 24-Hour T owing Assistance coverage details in the DaimlerChrysler Motors Company 24-Hour T owing As- sistance Program Guide.
W ARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear . Adjustable head restraints should be adjusted so that the upper edge is as high as practical. The head restraints have a locking button that must be pushed inward to lower the head restraint.
Power Seat Adjuster — If Equipped W ARNING! Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
This seat also has a manual recline lever located just to the rear of the power seat switch. Pull up on the lever to recline the seat. 65/35 Split Folding Rear Seat T o provide additional storage area, each rear seat can be folded flat to allow for extended cargo space and still maintain some rear seating room.
W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. • Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
NOTE: When lifting up on the release handle, the seatback will release easier if you do not pull forward on the seatback; only lift up on the release handle until the seatback disengages, then fold the seat forward. When the seatback is folded completely forward, the head restraints should be flush against the seat cushion.
Heated Seats — If Equipped The heated seat switch is located on the outboard side of the front seats. Pressing this switch to its desired setting (HI or LO) will activate the respective heating element for the heated seat. Once the heated seat switch is activated, depressing it a second time will de-activate it.
Then, reach under the hood and slide the safety latch to the right and lift the hood. T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approximately 12 inches (30 cm) and then push hood closed. This should secure both latches.
The overhead lights will automatically turn off in about 8 minutes if a door is left open or the dimmer contr ol is left in the dome light position. T urn the ignition switch ON to restor e the overhead light operation.
Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the r ecessed ar ea of the lens. T o turn these lights of f, press the r ecessed area of the lens a second time.
Parking Lights, Instrument Panel Lights, and Headlights T urn the end cap of the multi-function contr ol lever to the first detent for parking lights and instrument panel lights.
NOTE: A tone will chime if the turn signals are left on for more than 2 miles (3.2 km). Lights-On Reminder A chime will sound if the driver’s door is left open, and the headlights or parking lights are left on.
Light Bar — If Equipped 1. Remove lamp covers by pressing the thumb tab up- wards, and pulling the cover off. CAUTION! The auxiliary lights mounted on the off road light bar should be illuminated during ( OFF-ROAD USE ONL Y . ( Having them illuminated on public streets, highways, roads, etc.
2. W ith the ignition in the ON position, press the button to turn on the light bar (located on the instrument panel to the left of the steering column). Press the button again to turn off the light bar . An indicator light in the instrument cluster will illumi- nate when the light bar has been activated.
Windshield Washers T o use the washer , pull the lever toward you and hold while spray is desired. If the lever is pulled while in the delay range, the wiper will operate for two wipe cycles after the lever is released, and then resume the intermit- tent interval previously selected.
complete display cycle). After this, the display will continue to sequence. After fifteen “LOW ASH” se- quences, the VF display will no longer provide this warning. If the trip/reset button is pressed while the VF warnings are being displayed, the VF display will revert back to only displaying the odometer/trip odometer mileage.
Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable. Move the control lever to any of the first five wiper switch positions by turning the end cap of the control lever .
W ARNING! T ilting the steering column while the vehicle is moving is dangerous. W ithout a stable steering col- umn, you could lose control of the vehicle and have an accident. Adjust the column only while the ve- hicle is stopped. Be sure it is locked before driving.
T o Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. T o Deactivate A soft tap on the brake pedal, normal braking, or pr essing the CANCEL button will deactivate the Speed Control without erasing the memory .
NOTE: When driving uphill, at elevations above 2,000 ft. (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed. (If the vehicle speed drops below 30 mph (48 km/h), the Speed Control will automatically disengage).
Pressing the MENU button will change the displayed programming features. Pressing the STEP button will select the available choices. Pressing the C/T (Compass/ T emperature) button will return the display to the normal compass/temperature display . NOTE: T emperature accuracy can be effected from heat soak.
NOTE: The dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Electronic V ehicle Information Center The electronic vehicle information center (EVIC), when the appropriate conditions exist, displays the following messages and symbols.
• SP ARE LOW PRESSURE • SP ARE HIGH PRESSURE • TIRE PRESSURE UNA V AILABLE • TIRE PRESSURE NOW A V AILABLE • TIRE SENSOR BAD/MISSING • SP ARE SW AP DETECTED Tire Pressure Monitor System The T ire Pressur e Monitor (TPM) system uses wireless technology to monitor tire pr essure levels.
into the tire pressure display screen and flash the pres- sure value of the tire that is low or high. This will be displayed for the rest of the ignition cycle, or until the C/T , MENU, STEP , or RESET button is pressed. NOTE: This display will return 60 seconds after the C/T , MENU, STEP , or RESET button is pr essed.
4. In addition to monitoring the vehicle tires, the TPM system monitors faults within the system. When any fault has been set, the TPM system will display TIRE SENSOR BAD/MISSING.
Display U.S. or Metric? Pressing the STEP button when in this display selects US or Metric. The overhead console and instrument panel displays will be in the selected units. Auto Door Locks? When this feature is selected, all doors and the swing gate will lock automatically when the speed of the vehicle reaches 15 mph (25 km/h).
T o T rain Additional Key Fobs (using the EVIC module) 1. Press the MENU button until TRAIN REMOTE? NO is displayed. Press the STEP button to change to YES. Then, PRESS A V ALID FOB KEY will be displayed. Press either the “Lock” or “Unlock” button on the current key fob.
Headlamp Delay When this feature is selected the driver can choose, when exiting the vehicle, to have the headlamps remain on for 30, 60, or 90 seconds, or not remain on.
NOTE: The tire pressur e sensors must be retrained after rotating the tires or replacing one or more sensors. If a wheel rotation is not followed by the retrain procedure, the system will not properly inform you of the correct vehicle location for a low or high pressur e tire.
7. Repeat step 6 working clockwise around the vehicle (Left Front, Right Fr ont, Right Rear , Left Rear , Spar e) until all five TPM sensor positions are trained. 8. Return magnet to storage location. If the display reads TRAINING COMPLETE, pressing either the STEP , C/T , RESET , or MENU buttons will exit the training mode.
a resettable function is currently being displayed (A ver- age Economy , T rip Miles, and T ime Elapsed). A single chime will sound to indicate that a reset has occurred. Global Reset If the RESET button is pressed twice within 3 seconds while in any of the three resettable displays, the RESET button will reset all three displays.
A verage Miles/GAL Shows the average fuel economy in miles per gallon (MPG), or liters per 100 km (L/100 km) since the last reset. Miles T o Empty Shows the estimated distance that can be traveled before the fuel gauge shows E (Empty). The distance is calcu- lated by multiplying the amount of fuel r emaining by the projected fuel economy .
After completing three 360 degree turns in an area free from lar ge metal or metallic objects, the CAL symbol will turn off and the compass will function normally . Manual Compass Calibration If the compass appears erratic and the CAL symbol does not appear , you must manually put the compass into the “Calibration” mode.
T o set the variance: T urn the ignition ON and set the display to “Compass/T emperature.” Press and hold the RESET button five seconds (no more than 10 seconds). The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
CAUTION! Changes or modifications not expressively approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Retain the original transmitter of the RF device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes.
W ARNING! Y our motorized door or gate will open and close while you are programming HomeLink. Do not program HomeLink if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
NOTE: If the HomeLink display does not change to TRAINED, contact HomeLink at www .homelink.com or call 1-800-355-3515 for assistance. 4. Press and hold the just-trained HomeLink button. TRANSMIT should appear on the display . If your device activates when the HomeLink button is depressed and released, programming is complete.
HomeLink should now activate your rolling code equipped device. NOTE: T o program the remaining two HomeLink but- tons, simply repeat the 9 Programming Homelink 9 pro- cess.
Proceed with the remaining steps under 9 Programming HomeLink 9 to complete. Using HomeLink T o operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener , gate operator , security system, entry door lock, home/office lighting, etc.
Press and hold the “V” button in the center of the sunroof switch to open the vent. The sunroof can be stopped at any position between closed and full vent.
Express Open Feature During the Express Open operation, any movement of the switch will stop the sunroof and it will remain in a partial open position. Again, momentarily pressing the switch rearwar d will activate the Express Open Feature. T o close the sunroof, hold the switch in the forward position.
POWER OUTLET T o the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the top of the plastic cover to open the outlet. There is a rear power outlet located in the right rear cargo area above the storage cargo net/CD changer (if equipped).
The rear power outlet is a direct feed from the battery so it receives power whether the ignition is in the ON or OFF position. All accessories connected to this outlet should be re- moved or turned off when the vehicle is not in use.
CIGAR LIGHTER — IF EQUIPPED The lighter is a direct feed from the battery so it receives power whether the ignition is in the ON or OFF position. It heats when pushed in and pops out automatically when ready for use. T o preserve the heating element, do not hold the lighter element in the heating position.
CUP HOLDERS In the center console there are two cup holders for the front seat passengers. NOTE: The front cup holder insert is removable from the console, for cleaning. Smoker’s Package — If Equipped W ith the optional Smoker’s package, a removable ash tray is inserted into the front cup holder location.
CARGO AREA FEA TURES Cargo Light The cargo area light is activated by opening the swing gate, opening any door , or by rotating the dimmer control on the multi-function control lever to the extreme top position. If all doors are closed and only the swing gate is open, pushing on the cargo light lens surface will turn off all interior lights.
W ARNING! In an accident a cargo cover loose in the vehicle could cause injury . It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment. Remove the cover from the vehicle when taken from its mounting.
W ARNING! • Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or colli- sion a hook could pull loose and allow the child seat to come loose. A child could be badly injured. Use only the anchors provided for child seat tethers.
Cargo Organizer — If Equipped This vehicle may be equipped with a car go organizer that mounts on the floor behind the rear seat. Items may be placed on the flat surface or stored in the three storage compartments. W ARNING! • T o avoid tipping, lock the shelf securely in all positions.
2. Place the rear corners of the cargo organizer into the supports located on the rear trim panel. Press down on the back of the cargo organizer to lock it into place. W ARNING! Do not load objects over 30 lbs (13.5 kg) in the upper position. Failure to follow this warning could cause the cargo organizer to collapse resulting in personal injury .
T o Open Storage Compartments 1. Pull up on the center opening of the cargo organizer . 2. Lift up on the storage compartment dividers and lock into place. Cargo Organizer Removal Loosen screw , then lift lever from each mount located on the floor of the rear cargo area, and remove the cargo organizer from the vehicle.
CAUTION! • T o avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity of 150 lbs (68 kg) or 65 lbs (29.5 kg) on Renegade models. Always distribute heavy loads as evenly as possible and secure the load appropriately .
I n f o r m a t i o n P r o v i d e d b y :.
UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS m Instrument Panel And Interior Controls ....... 1 4 9 m Instrument Cluster ...................... 1 5 0 m Instrument Cluster Description ............. 1 5 1 m Electronic Digital Clock .................. 1 5 8 ▫ Clock Setting Procedur e.
▫ T o Set The Push-Button Memory .......... 1 6 1 ▫ Balance ............................ 1 6 2 ▫ Fade .............................. 1 6 2 ▫ Bass And T reble T one Control ............ 1 6 2 ▫ AM/FM Selection ..................... 1 6 2 ▫ Mode Button .
m Satellite Radio — If Equipped .............. 1 9 0 ▫ System Activation ..................... 1 9 0 ▫ Electronic Serial Number/Sirius Identification Number (ENS/SID) .................... 1 9 0 ▫ Selecting Satellite Mode In RBB And RBK Radios .
▫ Operating T ips ....................... 2 0 2 m Rear W indow Features ................... 2 0 3 ▫ Rear W indow W iper/W asher ............. 2 0 3 ▫ Rear W indow Defroster .
INSTRUMENT P ANEL AND INTERIOR CONTROLS UNDERST ANDING YOUR INSTRUMENT P ANEL 149 4 I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER 150 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v i d e d b y :.
INSTRUMENT CLUSTER DESCRIPTION 1. T achometer Indicates the permissible engine revolutions-per-minute for each gear range. Before reaching the red area, ease up on the accelerator to prevent engine damage. 2. T urn Signal Indicator Light The arrows will flash in unison with the exterior turn signals, when using the multi-function control lever .
the vehicle’s handling and stopping ability . Each tire, including the spare, should be checked monthly when cold and set to the recommended inflation pressur e as specified on the vehicle placard. 6. 4LO Mode Indicator Light — If Equipped This light alerts the driver that the vehicle is in the 4 LO four–wheel drive mode.
light will come on when the ignition switch is turned to the ON position and may stay on for as long as three seconds. If the light comes back on immediately or comes on during driving, it indicates t.
towing a trailer . It should not be allowed to exceed the upper limits of the normal operating range. If the pointer rises to the red zone (five chimes will occur), pull over and stop the vehicle. Do not turn the engine off. Idle the vehicle with the air conditioning turned off, until the pointer drops back into the normal range.
14. Cruise Indicator Light This indicator lights when the speed control system is turned ON. 15. Oil Pressure W arning Light Shows low engine oil pr essure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started.
W ARNING! Driving a vehicle with the BRAKE warning light on is dangerous. A significant decrease in braking per- formance or vehicle stability during braking may occur . It will take you longer to stop the vehicle or will make your vehicle harder to control.
the system is arming. After the alarm successfully arms, the light will flash at a slower rate to indicate the alarm is set. 21. Fuel Gage When the ignition key is in the ON position, the pointer will show the level of fuel remaining in the fuel tank.
when driving, if the driver seat belt remains unbuckled, the Seat Belt W arning Light will flash or remain on continuously . Refer to 9 Enhanced Driver Seat Belt Re- minder System (BeltAlert™) 9 in the Occupant Restraints section for more information.
you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals.
SALES CODE RBB—AM/FM STEREO RADIO WITH CASSETTE T APE PLA YER AND CD CHANGER CAP ABILITY Operating Instructions NOTE: Power to operate the radio is supplied through the ignition switch.
For your convenience, the volume can be turned down, but not up, when the audio system is off and the ignition is ON. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down.
Every time a preset button is used a corresponding button number will be displayed. Balance The balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The fade control provides for balance between the front and rear speakers.
Y ou can turn the tape player ON by inserting a cassette or activating the MODE button (with a cassette in the radio), but only when the ignition and radio are on. Each time a cassette is inserted the tape player will begin playing on the side of the cassette that is facing up in the player .
NR (Noise Reduction) Pushing the Number 2 Pre-set button when a tape is playing deactivates the Dolby Noise Reduction System*. When Dolby is ON, the NR symbol appears on the display . Each time a tape is inserted the Dolby will turn ON. * “Dolby” noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily . Skipping will not damage the disc or the player , and play will resume automatically .
Radio Display Messages Y our radio has been designed to display certain messages when a problem is detected with the CD player . 166 UNDERST ANDING YOUR INSTRUMENT P ANEL I n f o r m a t i o n P r o v.
SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLA YER AND CD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
the radio will continue to tune until you release the button. The frequency will be displayed and continu- ously updated while the button is pressed. Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out.
both AM and FM. This allows a total of 10 AM and 10 FM stations to be locked into push-button memory . The stations stored in SET 2 memory can be selected by pressing the push-button twice. Every time a preset button is used a corresponding button number will be displayed.
If you insert a disc with the ignition ON and the radio OFF , the display will show the time of day . If the power is ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the track number and index time in minutes and seconds.
Mode Press the MODE button repeatedly to select between the CD player , the optional remote CD changer and the Satellite Radio (if equipped). When Satellite Radio (if equipped) is selected “SA” will appear in your radio display . A CD or tape may remain in the player while in the Satellite mode.
Random Play (RND) Press the Random button to play the tracks on the selected disc in random order for an inter esting change of pace. Random can be cancelled by pressing the button a second time or by ejecting the CD from the changer . CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily .
Radio Display Messages Y our radio has been designed to display certain messages when a problem is detected with the CD player . UNDERST ANDING YOUR INSTRUMENT P ANEL 173 4 I n f o r m a t i o n P r o.
SALES CODE RBP—AM & FM STEREO RADIO WITH CASSETTE T APE PLA YER, CD PLA YER, AND OPTIONAL CD/DVD CHANGER CONTROLS Radio Operation Power/V olume Control Press the ON/VOL control to turn the radio on. T urn the volume control to the right to increase the volume.
T oggle the PTY button to select the following format types: Program T ype Radio Display Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Information Inform.
The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station. If no station is found with the selected PTY program type, the radio will return to the last preset station.
Fade The Fade control provides for balance between the front and rear speakers. Press the F ADE button in and it will pop out. Adjust the balance and push the button back in. T one Control The tone controls affect the BASS and TREBLE frequency bands. Each is contr olled by a slider control with a detent at the mid position.
T o set the clock, use a ballpoint pen or similar object to press the hour (H) or minute (M) buttons on the radio, The time setting will increase each time you press the button. Press any other button to exit from the clock setting mode. General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada.
Seek Press the SEEK button up for the next selection on the tape and down to return to the beginning of the current selection. Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc.
the tape from any damage. When power is restored to the tape player , the pinch roller will automatically reengage and the tape will resume play . Dolby Noise Reduction The Dolby Noise Reduction System* is on when- ever the tape player is on, but may be switched on/off.
Seek Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection.
T o select Satellite Radio (if equipped), press the MODE button until the word SIRIUS™ appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds. The current program type and channel number will then be displayed for five seconds.
Disc Down/Program Button 5 Press the DISC (button 5) button to play the previous disc. Seek Press the top of the SEEK button for the next selection on the CD.
Radio Operation Power/V olume Control Press the PWR/VOL control to turn the radio on. T urn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Balance — BAL The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers.
General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
show the disc number , the track number , and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load” insert the CD into the player .
FF/TUNE/R W Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner . Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play .
Program T ype Radio Display Information Inform Jazz Jazz Foreign Language Language News News Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Mu.
By pressing the SCAN button when the PTY icon is displayed, the radio will stop at every PTY station on the band and list each corresponding program type in the radio display . T ime Press the TIME button to change the display from elapsed CD playing time to time of day .
ESN/SID Access W ith RBB and RBK Radios W ith the ignition switch in the ACCESSORY position and the radio OFF , press the T ape Eject or CD Eject (depend- ing on the radio type) and T ime buttons simultaneously for 3 seconds. The first four digits of the twelve-digit ESN/SID number will be displayed.
• The current channel number will then be displayed until an action occurs. A CD or tape may remain in the radio while in the Satellite radio mode. Selecting a Channel Press and r elease the SEEK or TUNE buttons to sear ch for the next channel. Press the top of the button to search up and the bottom of the button to search down.
PTY Button ( SCAN ( When the desired program type is obtained, press the 9 SCAN 9 button within five seconds. The radio will play 7 seconds of the selected channel befor e moving to the next channel of the selected program type. Press the 9 SCAN 9 button a second time to stop the search.
• Driving under wide bridges or along tall buildings can cause intermittent reception. • Placing objects over or too close to the antenna can cause signal blockage. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls ar e located on the rear surface of the steering wheel.
Pressing the center button will make the radio switch between the various modes available (AM/FM/T APE/ CD, Etc.). The left hand control is a rocker type switch with a push-button in the center . The function of the left hand control is dif ferent depending on which mode you are in.
If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. CD Player — 6 Disc in Cargo Area Pressing the top of the switch once will go to the next track on the CD.
Maintain your cassette tape player . The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played. The result of deposits on the capstan shaft may cause the tape to wrap around and become lodged in the tape transport.
RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular phone being On in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the cellular phone antenna. This condition is not harmful to the radio.
T emperature Control The degree of comfort can be selected by rotating the temperature control knob on the right. The coldest tem- perature setting is fully counterclockwise and the warm- est setting fully clockwise. The knob can be positioned at any detent.
Mix Air flows through the floor outlets, the outlets at the base of the windshield, and the side window demisters outlets. Defrost Air flows through the outlets at the base of the windshield and thr ough the side window demister outlets.
T emperature Control The degree of comfort can be selected by rotating the temperature control knob on the right. The coldest tem- perature setting is fully counterclockwise and the warm- est setting fully clockwise. The knob can be positioned at any detent.
Panel Air flows through the outlets located in the instru- ment panel. Slight airflow from the defrost outlet, located at the base of the windshield, may be noticed. Floor Air flows through the floor outlets located under the instrument panel and through the outlets lo- cated in the r ear of the center console.
W indow Fogging In mild but rainy or humid weather , windows will fog on the inside. T o rapidly clear the fog off all the windows, select the defrost mode, turn the temperature control knob fully clockwise, and position the blower control to its highest speed.
If the rear wiper is operating when the ignition is turned OFF , the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at.
The defroster will automatically turn off after about ten minutes. For about five more minutes of operation, push the button again. T o prevent excessive battery drain, use the defroster only when the engine is operating. The push button also activates the heated exterior mirrors, if so equipped.
I n f o r m a t i o n P r o v i d e d b y :.
ST ARTING AND OPERA TING CONTENTS m Starting Procedur es ..................... 2 1 0 ▫ Manual T ransmission .................. 2 1 0 ▫ Automatic T ransmission ................ 2 1 0 ▫ Normal Starting ...................... 2 1 0 ▫ Extreme Cold W eather .
▫ Shifting Procedur e .................... 2 3 0 m T rac-Lok™ Rear Axle — If Equipped ......... 2 3 1 m Parking Brake ......................... 2 3 2 m Anti-Lock Brake System — If Equipped ....... 2 3 4 m On-Road Driving T ips ................
▫ T ire Pressur e Monitor System/4–Lo Mode — If Equipped ....................... 2 5 6 ▫ General Information ................... 2 5 6 m T ire Chains ........................... 2 5 7 m T ire Rotation Recommendations ............ 2 5 8 m Fuel Requirements .
ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. W ARNING! Do not leave children or animals inside parked vehicles in hot weather . Interior heat build up may cause serious injury or death.
W ARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury .
If the engine has been flooded, it may start to r un, but not have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- erator pedal pushed all the way to the floor . Release the accelerator pedal and the key once the engine is running smoothly .
W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-115 volt AC electrical cord could cause electrocution. Use the heater when temperatures below 0°F (-18°C) are expected to last for several days. TRANSMISSION SHIFTING 5-Speed Manual Overdrive T ransmission Follow the shift pattern on the gearshift knob.
CAUTION! T o drive as safely as possible and to prolong the life of your manual transmission, follow these tips: • Before shifting from a forward gear into reverse, or from reverse to a forward gear , stop vehicle com- pletely . Otherwise, accelerated transmission wear may result.
• The manual transmission may be equipped with a “Reverse Blocker” to prevent inadvertent shifts from 5th gear to Reverse. If you experience difficulty shift- ing into “Reverse”, make sure that you are not inad- vertently moving the shift lever toward 5th gear when shifting into “Reverse.
Automatic T ransmission Shifting from D (Drive) to P (Park) or R (Reverse) (or from P or R to D) should be done only after the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake when moving the shift lever between these gears.
Gear Ranges P (Park) Supplements the parking brake by locking the transmis- sion. The engine can be started in this range. Never use P (Park) while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply the parking brake first, and then place the selector in P (Park) position.
• When shifting into P (Park), depress the button on the shift lever and firmly move the lever all the way forward until it stops. • Look at the shift indicator window on the console to ensure it is in the P (Park) position.
Overdrive (O/D) For most city and highway driving. The transmission contains an electronically controlled Overdrive, and will automatically shift from D (Drive) to O/D (Overdrive) if the following conditions are present: • The transmission selector is in D (Drive).
NOTE: If the vehicle is started in cold outside tempera- tures, shifts into Overdrive may be delayed. Normal Overdrive and shifting operation will resume when the temperature of the transmission reaches the appropriate temperature. Refer to the “Note” under “T orque Con- verter Clutch” later in this section.
Over T emperature Mode The transmission electronics constantly monitor the transmission oil temperature. If the transmission gets too hot, the transmission will change the way it shifts to help control the condition. This may r esult in a slightly differ ent feeling or response during normal operation in D (Drive) position.
FOUR-WHEEL DRIVE OPERA TION Command-T rac T Operating Information/Precautions The Command-T rac t transfer case provides 4 mode position s-2( r ear) wheel drive high range, 4-wheel drive high range, neutral, and 4-wheel drive low range.
CAUTION! • Do not attempt to make a shift while only the front or rear wheels are spinning. The Command- T rac transfer case is not equipped with a synchro- nizer and therefore the front and rear driveshaft speeds must be equal for the shift to take place.
W ARNING! • Because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road con- ditions permit. • Y ou or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake.
4L 4-Wheel-Drive Low Range - Low speed 4 wheel drive. Locks the front and rear driveshafts together . Forces the front and r ear wheels to rotate at the same speed. Additional traction and maximum pulling power for loose, slippery road surfaces only .
NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur .
The P AR T TIME indicator light, located on the instru- ment cluster , illuminates when the transfer case is shifted to the 4 P AR T TIME position. The FULL TIME indicator light, located on the instru- ment cluster , illuminates when the transfer case is shifted to the 4 FULL TIME position.
Proper operation of 4-wheel drive vehicles depends on tires of equal size, type, and cir cumference on each wheel. Any difference will adversely affect shifting and can cause damage to the transfer case. W ARNING! • Because 4-wheel drive provides improved trac- tion, there is a tendency to exceed safe turning and stopping speeds.
Shift Positions For additional information on the appropriate use of each transfer case mode position see the information below: 2WD Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4 P AR T TIME Part T ime 4–Wheel Drive High Range - Locks the transfer case inter-axle differential.
Shifting Procedure 2WD to 4 P AR T TIME or 4 P AR T TIME to 2WD Shifting between 2WD and 4 P ART TIME can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). W ith the vehicle in motion two momentary releases of the accelerator pedal may be r equired after shifting.
rearwar d into 4LO. In 4 FULL TIME, there is a neutral stop to prevent shifting into N (Neutral) by accident. NOTE: Pausing in transfer case N (Neutral) in vehicles equipped with an automatic transmission may require shutting the engine OFF to avoid gear clash while completing the shift.
W ARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel of f the ground. The vehicle may drive through the rear wheel remaining on the ground and cause you to lose control of your vehicle. P ARKING BRAKE T o set the parking brake, pull the lever up as firmly as possible.
Before leaving the vehicle parked on a hill, you must make sure the parking brake is fully applied and place the gear selector in the P (Park) position. Make certain the transfer case is in gear . Failure to do so may cause the vehicle to roll and cause damage or injury .
ANTI-LOCK BRAKE SYSTEM — IF EQUIPPED The Anti-Lock Brake System is designed to aid the driver in maintaining vehicle control under adverse braking conditions. The system operates with a separate com- puter to modulate hydraulic pressur e to prevent wheel lock-up and help avoid skidding on slippery surfaces.
W ARNING! Pumping of the Anti-Lock Brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop.
CAUTION! The Anti-Lock Brake System is subject to possible detrimental effects of electronic interference caused by improperly installed aftermarket radios or tele- phones. NOTE: During severe braking conditions, a pulsing sensation may occur and a clicking noise will be heard.
In Snow , Mud and Sand In heavy snow , when pulling a load, or for additional control at slower speeds, shift the transmission to a low gear and shift the transfer case to 4L or 4 LO if necessary . Don’t shift to a lower gear than necessary to maintain headway .
Remember , never drive diagonally across a hill-always drive straight up or down. If the wheels start to slip as you approach the crest of a hill, ease off the accelerator and maintain headway by turning the front wheels sharply left and right.
• After extended operation in mud, sand, water , or similar dirty conditions, have brake rotors, wheels, brake linings, and axle yokes inspected and cleaned as soon as possible. W ARNING! Abrasive material in any part of the brakes may cause excessive wear or unpredictable braking.
• European Metric tire sizing is based on European design standards. T ires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter 9 P 9 is absent from this tire size designation. Example: 215/65R15 96H • L T(Light T ruck)-Metric tire sizing is based on U.
T ire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards LT = Light T ruck tire based on U.
EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry . H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. T ires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Tire Loading and Tire Pressure T ire Placard Location NOTE: Some vehicles have a “T ire and Loading Infor- mation” placard located on the driver’s side “B” pillar .
4) the cold tire inflation pressures for the front, rear and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
3. Subtract the combined weight of the driver and pas- sengers from XXX kilograms or XXX pounds. 4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1400 lbs. and there will be five 150 lb.
ST ARTING AND OPERA TING 247 5 I n f o r m a t i o n P r o v i d e d b y :.
W ARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle.
2. Economy— Improper inflation pr essures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will r educe tread life r esulting in a need for earlier tire replacement. Under inflation also increases tire r olling resistance and results in higher fuel consump- tion.
The tire pressur e should be checked and adjusted at least once every month. Check more often if subject to a wide range of outdoor temperatures, as tire pressur es vary with temperature changes. Inflation pressur es specified on the label ar e always “Cold Inflation Pressure.
Radial-Ply Tires W ARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly . The instability could cause an accident. Al- ways use radial tires in sets of four . Never combine them with other types of tires.
T read Wear Indicators These indicators are narrow strips 1/16 inch (1.6 mm) thick and are found in the tread pattern grooves. When the tread pattern is worn down to these treadwear indicators, the tires should be replaced. Overloading your vehicle, long trips in very hot weather , and driving on bad roads may result in greater wear .
W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unap- proved tires and wheels may change suspension dimen- sions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
T ires may also cause the vehicle to pull left or right. Alignment will not correct this problem. See your dealer for proper diagnosis of the problem. Improper alignment will not normally cause vehicle vibration, which may be a result of tire and wheel out-of-balance.
The following chart indicates the TPM system pressure levels. A threshold is the level at which the TPM system provides you with an indication. High Pressur e Threshold 44 psi (303 kPa ) Placard Pressure (Cold) 33 psi (227 kPa) Low Pressur e Threshold 25 psi (172 kPa) NOTE: A TPM system does not replace normal tire maintenance.
Tire Pressure Monitor System Tire/Wheel Rotation and Sensor Replacement — If Equipped W ith the TPM System, if a road tire and wheel is replaced by the spare, the TPM system will detect the swap automatically (after the ignition has been cycled) and display SP ARE SW AP DETECTED along with a chime.
• This device must accept any interference received, including interference that may cause undesired op- eration. The tire pressur e sensors are covered under one of the following licenses: United States ..................... KR5S120123 Canada .....
T ire chains that are recommended for this vehicle are listed below: • Mopar t P/N 82206828 with P235/70R16 and P235/ 65R17 tires. • Mopar t P/N 82207074 with P215/75R16 tires. NOTE: In order to avoid damage to tires, chains, and your vehicle do not drive for a prolonged period of time on dry pavement.
NOTE: The T ire Pressure Monitor system must be retrained following a tire rotation. See your authorized dealer for service. The suggested rotation method is the “forward-cr oss” shown in the following diagram.
Light spark knock at low engine speeds is not harmful to your engine. However , continued heavy spark knock at high speeds can cause damage and immediate service is requir ed. Engine damage resulting fr om operation with a heavy spark knock may not be covered by the new vehicle warranty .
CAUTION! DO NOT use gasoline containing METHANOL. Gasoline containing methanol may damage critical fuel system components. MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase octane.
CAUTION! If the “Malfunction Indicator Light” is flashing, immediate service is required. See “Onboard Diag- nostic System” in Section 7 of this manual. Materials Added T o Fuel All gasoline sold in the United States is required to contain effective detergent additives.
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap). A poorly fitting cap could let impurities into the fuel system. W ARNING! • Remove the fuel cap slowly to prevent fuel spray from the filler neck which may cause injury .
TRAILER TOWING In this section you will find information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer , carefully review this information to tow your load as efficiently and safely as possible.
CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances.
Minimum V ehicle Requirements for T railer T owing 266 ST ARTING AND OPERA TING I n f o r m a t i o n P r o v i d e d b y :.
RECREA TIONAL TOWING (BEHIND MOTORHOME, ETC.) T owing – 2WD Models Recreational towing is not recommended. Provided that the transmission is operable, tow only in N (Neutral) at speeds not exceeding 45 mph (72 km/h) and distances less than 100 miles (161 km).
CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (Neutral) before recreational towing to prevent damage to internal parts. 1. Depress brake pedal. 2. Shift transmission into N (Neutral). 3. Shift transfer case lever into N (Neutral).
Shifting Out Of Neutral (N) Use the following procedure to prepar e your vehicle for normal usage. 1. Shift transmission into N (Neutral). 2. Shift transfer case lever to desired position. 3. Shift automatic transmission into D (Drive) or manual transmission into any forward gear .
SNOW PLOW Snow plows, winches, and other aftermarket equipment should not be added to the front end of your vehicle. The airbag crash sensors may be affected by the change in the front end structur e. The airbags could deploy unexpect- edly or could fail to deploy during a collision.
WHA T T O DO IN EMERGENCIES CONTENTS m Hazard W arning Flashers ................. 2 7 2 m If Y our Engine Overheats ................. 2 7 3 m Changing A Flat T ire .................... 2 7 4 ▫ Jack And Lug W rench Locations ........... 2 7 4 ▫ Spare T ire Location .
HAZARD W ARNING FLASHERS Y our vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently . Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
IF YOUR ENGINE OVERHEA TS In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- tion. • On the highways — Slow down. • In city traffic — While stopped, put transmission in N (Neutral), but do not increase engine idle speed.
CHANGING A FLA T TIRE Jack And Lug Wrench Locations The jack, jack handle, and lug wrench are stored beneath the right rear seat. T o remove the jack from its stowage position, turn the thumb screw counterclockwise to loosen jack assembly and then remove it.
Spare Tire Location T o remove the spare tire from the carrier , remove the tire cover , if equipped, and remove the lug nuts with the lug wrench turning them counterclockwise.
Preparation • Park on a firm, level surface well off the road, to provide ample work space. Place automatic transmis- sion in P (Park), or manual transmission in R (Re- verse), and stop engine. Set parking brake firmly and activate hazard warning flasher .
5. Raise the vehicle by turning the jack handle clockwise until the tire clears the ground. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable and cause an accident. It could slip off the jack and hurt someone near it.
9. Finish tightening the lug nuts securely in crisscross pattern. Have an authorized service technician check that the torque is 85-1 10 ft. lbs. (1 15-149 N·m) as soon as possible. 10. Remove jack assembly and wheel blocks. 1 1. Secure jack, lug wrench, jack handle driver , jack extension, and tire in proper locations.
• Do not let passengers sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. • Failure to follow the “T ire Changing Procedur e” may result in personal injury or damage to your vehicle. • Only use the jack in the positions indicated.
7. When removing the jumper cables, reverse the above sequence exactly . Be careful of the moving belts and fan. NOTE: T o start the vehicle following connection of a booster battery , the Security Alarm System must first be disabled by cycling a front door key cylinder or by using the keyless entry transmitter .
W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic converter and, once the engine has started, ignite and damage the converter and vehicle. EMERGENCY TOW HOOKS — IF EQUIPPED If your vehicle is equipped with tow hooks, they are mounted in the front and the rear .
I n f o r m a t i o n P r o v i d e d b y :.
MAINT AINING YOUR VEHICLE CONTENTS m 2.4L Engine ........................... 2 8 5 m 3.7L Engine ........................... 2 8 6 m Onboard Diagnostic System — OBD II ........ 2 8 7 m Emissions Inspection And Maintenance Programs ..................
▫ Power Steering Fluid Check .............. 3 0 0 ▫ Driveline And Steering Component Lubrication .......................... 3 0 1 ▫ Body Lubrication ..................... 3 0 1 ▫ W indshield W iper Blades ................ 3 0 1 ▫ W indshield W ashers .
2.4L ENGINE MAINT AINING YOUR VEHICLE 285 7 I n f o r m a t i o n P r o v i d e d b y :.
3.7L ENGINE 286 MAINT AINING YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :.
ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems.
EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
ignition key or start the engine. This means that your vehicle’s OBD system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine.
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! Y ou can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment.
The best time to check the engine oil level is about 5 minutes after a fully warmed engine has been shut of f, or before starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings.
CAUTION! Overfilling or underfilling the crankcase will cause aeration or loss of oil pressure. This could damage your engine. Change Engine Oil Road conditions as well as your kind of driving affect the interval at which your oil should be changed.
Engine Oil Selection For best performance and maximum protection for all engines under all types of operating conditions, the manufacturer recommends engine oils that are API Cer- tified and meet the requirements of DaimlerChrysler Material Standard MS-6395.
Materials Added T o Engine Oils The manufacturer strongly recommends against the ad- dition of any additives (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives.
Special tools are requir ed to properly measure tension and to restore belt tension to factory specifications. Also, check belt routing to make sure there is no interference between the belts and other engine components. Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control.
W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Engine Timing Belt — 2.4L Engine Replace the engine timing belt at the intervals described in the appropriate maintenance schedule. Ignition Wiring System — 2.4L Engine Replace the ignition cables at the intervals described in the appropriate maintenance schedule.
Maintenance-Free Battery Y our vehicle is equipped with a maintenance-fr ee battery . Y ou will never have to add water , nor is periodic main- tenance requir ed. W ARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds.
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar - bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product.
Driveline And Steering Component Lubrication U-joints (cardan joints) are sealed and do not requir e lubrication. Prop shafts, yokes, ball joints and other driveline and steering components may be pr ovided with grease fittings for lubrication.
remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Washers The fluid reservoir for the windshield washers and the rear window washer is shared.
or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into the passenger compartment.
If the solution is dirty and contains a considerable amount of sediment, clean and flush with reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals. Engine Coolant Disposal Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal.
Adding Coolant When adding coolant, a minimum solution of 50% rec- ommended ethylene glycol antifreeze coolant in water should be used. Use higher concentrations (not to exceed 70%) if temperatures below -37°F (-38°C) are anticipated. Use only high purity water such as distilled or deionized water when mixing the water/antifreeze solution.
Coolant Level The coolant r ecovery bottle provides a quick visual method for determining that the coolant level is ad- equate. The coolant level must be at or above the COLD FULL level on the bottle.
moisture from rain, snow , or high humidity accumulat- ing on the radiator and being vaporized when the thermostat opens, allowing hot water to enter the radia- tor . If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven.
Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and couplings to make sure they are secure and no leaks are present. Components should be replaced immedi- ately if there is any evidence of degradation that could cause failure.
Inspect all hose clamps and couplings to make sure they are secure and no leaks are present. NOTE: Often fluids such as oil, power steering fluid, and brake fluid are used during assembly plant opera- tions to ease the assembly of hoses to couplings. There- fore, oil wetness at the hose-coupling area is not neces- sarily an indication of leakage.
Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the “Brake W arning Light” shows system failure. Be sure to clean the top of the master cylinder area befor e removing the cap.
W ARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from for eign matter . Do not allow petroleum base fluid to contaminate the brake fluid as seal damage will result.
T o check the automatic transmission fluid level properly , the following procedur e must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3. Fully apply parking brake. 4.
Hydraulic Clutch Fluid — Manual T ransmission The clutch hydraulic system is a sealed maintenance free system. In the event of leakage or other malfunction, the system must be replaced.
The fluid level should be to the bottom edge of the fill hole (A) when the vehicle is in a level position. Adding Fluid Only at filler hole until fluid runs out of the hole, when the vehicle is in a level position. Drain First remove fill plug (B), then drain plug (C).
Front/Rear Axle Fluid The front axle has a threaded “fill plug” on the cover plate, and a threaded “drain plug” on the bottom side of the carrier . Fluid Level Check Lubricant should be 1/2 9 (1 cm) below the oil fill hole. Adding Fluid Add lubricant only at the fill hole and only to the level specified above.
The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar . • Salt in the air near sea-coast localities. • Atmospheric fallout/industrial pollutants. W ashing • W ash your vehicle regularly .
• If you detect any stone chips or scratches in the paint, touch them up immediately . The cost of such repairs is considered the responsibility of the owner . • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle r epaired as soon as possible.
Leather Seat Care & Cleaning Leather is best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather surface and should be removed pr omptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and Mopar t T otal Clean.
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water . Do not remove the belts from the vehicle to wash them.
FUSE P ANEL Interior Fuses The fuse panel is on the left side of the instrument panel. A label is attached to the fuse panel cover to identify each fuse for ease of replacement.
Fuse Panel Description Cavity Fuse Description 1 15 Amp Blue Horn Relay , Power Sunroof Relay , Power W indow Relay 2 10 Amp Red Rear Fog Lights (Export Only) 3 20 Amp Y el- low Cigar Lighter 4 10 Amp.
Cavity Fuse Description 18 20 Amp Y el- low Radio Choke & Relay 19 20 Amp Y el- low Frt Fog Lights/T railer T ow Stop and T urn Lights 20 Spare 21 10 Amp Red Radio 22 20 Amp Y el- low Power Sunroo.
Cavity Fuse Description 37 10 Amp Red Airbag Control Module 38 10 Amp Red ABS Controller/Shifter As- sembly 39 10 Amp Red Hazard Flasher (T urn Signals)/Backup Lamp Switch (Manual T ransmission Only)/.
VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days you may want to take steps to protect your battery . Y ou may: • Remove Cartridge fuse #15 in the Power Distribution Center labeled Ignition-Off Draw (IOD). • Store the removed IOD fuse in the Power Distribution Center location #1 1 labeled “IOD Storage.
Exterior Lights Bulb T ype Backup Lights .................... 3157 P27/7W Center High-Mounted Stoplight ......... 921/W16W Fog Lights ............................. 9145 Front Park/T urn Lights ............. 3157 P27/7W Front Side Marker ..............
FLUID CAP ACITIES U.S. Metric Fuel (Approximate) 19.5 Gallons 74 Liters Engine Oil with Filter 2.4 & 3.7 Liter Engine (SAE 5W -30, API Certified Engine Oil) 5 Qts 4.7 Liters Cooling System * 2.4 Liter Engine (Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula) 10 Qts 9.
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar t Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hybrid Or- ganic Additive T echnology) Engine Oil Use API Certified SAE 5W -30 Engine Oil.
Chassis Component Fluid, Lubricant, or Genuine Part Automatic T ransmission Mopar t A TF+4 Automatic T ransmission Fluid Manual T ransmission Mopar t Manual T ransmission Lubricant (P/N 04874464) T ra.
MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance ........ 3 3 0 m Maintenance Schedules ................... 3 3 0 ▫ Schedule “B” .
EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system.
• Off-r oad or desert driving. NOTE: Most vehicles are operated under the conditions listed for Schedule “B.” Second is Schedule “A” . It is for vehicles that are not operated under any of the conditions listed under Sched- ule “B.” Use the schedule that best describes your driving condi- tions.
At Each Oil Change • Change the engine oil filter . • Inspect the exhaust system. • Inspect brake hoses. • Check the coolant level, hoses, and clamps.
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32°F (0°C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions.
Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (29 000) (34 000) (38 000) (43 000) (48 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary .
Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (53 000) (58 000) (62 000) (67 000) (72 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings. X Drain and refill the front and rear axle fluid‡ X Inspect the drive belt and replace as needed.
Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (77 000) (82 000) (86 000) (91 000) (96 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary .
Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (101 000) (106 000) (110 000) (1 15 000) (120 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings.
Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (134 000) (139 000) (144 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs. X Inspect and replace the PCV valve, if necessary .
Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (149 000) (154 000) (158 000) (163 000) (168 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Inspect the brake linings.
Miles 108,000 1 1 1,000 1 14,000 1 17,000 120,000 (Kilometers) (173 000) (178 000) (182 000) (187 000) (192 000) Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, replace if necessary . X Replace the spark plugs.
Inspection and service should be performed anytime a malfunction is observed or suspected. Retain all receipts. L This maintenance is recommended by the manufac- turer to the owner , but it is not requir ed to maintain emissions warranty .
Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (19 000) (29 000) (38 000) (48 000) [Months] [6] [12] [18] [24] [30] Change the engine oil and engine oil filter . X X X X X Inspect the engine air filter element, and replace if necessary .
Miles 36,000 42,000 48,000 54,000 (Kilometers) (58 000) (67 000) (77 000) (86 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter .
Miles 60,000 66,000 72,000 78,000 (Kilometers) (96 000) (106 000) (1 15 000) (125 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter . X X X X Inspect the brake linings. X Inspect the engine air filter element, and replace if nec- essary .
Miles 84,000 90,000 96,000 102,000 (Kilometers) (134 000) (144 000) (154 000) (163 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter . X X X X Inspect the brake linings. X Inspect the engine air filter element, and replace if nec- essary .
Miles 108,000 1 14,000 120,000 (Kilometers) (173 000) (182 000) (192 000) [Months] [108] [1 14] [120] Change the engine oil and engine oil filter . X X X Inspect the brake linings. X Inspect the engine air filter element, and replace if necessary . X Replace the spark plugs.
IF YOU NEED CONSUMER ASSIST ANCE CONTENTS m Suggestions For Obtaining Service For Y our V ehicle .............................. 3 4 8 ▫ Prepar e For The Appointment ............ 3 4 8 ▫ Prepar e A List ........................ 3 4 8 ▫ Be Reasonable W ith Requests .
SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty , discuss additional charges with the service manager .
The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer .
In Mexico contact: A v . Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P . 05109 Mexico, D. F . In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assi.
The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract.
352 IF YOU NEED CONSUMER ASSIST ANCE I n f o r m a t i o n P r o v i d e d b y :.
MOP AR T P ARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer . They will help you keep your vehicle operating at its best.
PUBLICA TION ORDER FORMS T o order the following manuals, you may use either the website or the phone numbers listed below . V isa, Mas- tercar d, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Call T oll Fr ee at 1–800–890–4038 (U.S.) or 1–800–387–1 143 (Canada) Or V isit us on the W orld W ide W eb at: www .techauthority .daimlerchrysler .
I n f o r m a t i o n P r o v i d e d b y :.
INDEX 10 I n f o r m a t i o n P r o v i d e d b y :.
Adding W asher Fluid ..................... 2 0 4 Air Cleaner , Engine ...................... 2 9 7 Air Conditioner Maintenance ............... 2 9 9 Air Conditioning ........................ 2 0 0 Air Conditioning Controls ............... 200,201 Air Conditioning, Operating T ips .
Auxiliary Power Outlet ................... 1 3 3 Bar , Light ............................. 1 0 3 Battery ............................... 2 9 8 Emergency Starting ..................... 2 7 9 Keyless T ransmitter Replacement ............ 2 7 Saving Feature .
Catalytic Converter ...................... 2 9 5 Caution, Exhaust Gas ...................... 6 8 CD Changer ...................... 164,171,182 CD Player ............... 167,169,174,180,183,186 CD Player Maintenance ................... 1 9 7 Cellular Phone .
Crankcase Emission Control System .......... 2 9 7 Cruise Control .......................... 1 0 8 Cruise Light ........................... 1 5 5 Cup Holder ............................ 1 3 6 Customer Assistance ..................... 3 4 8 Cylinder , Retest Requirements .
Jump Starting ......................... 2 7 9 T ow Hooks .......................... 2 8 1 Emission Control System Maintenance ...... 288,330 Engine Air Cleaner .......................... 2 9 7 Block Heater ......................... 2 1 2 Break-In Recommendations .
Flashers Hazard W arning ....................... 2 7 2 T urn Signal .......................... 1 5 1 Flat T ire Changing ....................... 2 7 4 Flooded Engine Starting ................... 2 1 1 Fluid Capacities ......................... 3 2 6 Fluid Leaks .
Gauges Coolant T emperature .................... 1 5 3 Fuel ................................ 1 5 7 Odometer ........................... 1 5 4 Speedometer ......................... 1 5 1 T achometer .......................... 1 5 1 Gear Ranges ........
Instrument Cluster ....................... 1 5 0 Instrument Panel and Controls .............. 1 4 9 Interior Appearance Care .................. 3 1 7 Interior Fuses .......................... 3 2 0 Interior Lighting ......................... 9 8 Interior Lights .
Dome .............................. 1 1 1 F o g ................................ 1 0 2 Four-Wheel Drive Indicator ............... 1 5 2 Fuses ............................... 3 2 0 Hazard W arning Flasher ................. 2 7 2 Headlight Switch ......
Lug Nuts ............................. 2 7 8 Luggage Carrier ......................... 1 4 2 Luggage Rack .......................... 1 4 2 Maintenance Free Battery .................. 2 9 8 Maintenance Procedur es ................... 2 9 0 Maintenance Schedule .
Odometer ............................. 1 5 4 T r i p ................................ 1 5 4 Off-Pavement Driving .................. 236,319 Off-Road Driving ........................ 3 1 9 Oil, Engine ............................ 2 9 0 Capacity .......
Mirrors .............................. 7 7 Outlet .............................. 1 3 3 Seats ................................ 9 3 Steering ............................. 3 0 0 Sunroof ............................. 1 3 0 W indows .......................
Replacement T ires ....................... 2 5 2 Reporting Safety Defects ................... 3 5 3 Restraint, Head .......................... 9 2 Restraints, Child ......................... 5 8 Restraints, Infant ......................... 5 9 Restraints, Occupant .
Security Against Theft ................... 20,28 Security Alarm .......................... 2 8 Selection of Oil ......................... 2 9 3 Selec-T rac Operation ...................... 2 2 6 Sentry Key ............................. 1 4 Sentry Key Programming .
Steering Power .............................. 3 0 0 Wheel Lock ........................... 1 7 Wheel, T ilt ........................... 1 0 7 Steering Wheel Mounted Sound System Controls ............................. 1 9 4 Storage ....................
Pressur e Monitor System .............. 1 13,254 Radial .............................. 2 5 1 Replacement ......................... 2 5 2 Rotation .......................... 256,258 Safety ............................ 70,239 Sizes .....................
Unleaded Gasoline ....................... 2 5 9 Upholstery Care ........................ 3 1 7 V acuum/V apor Harnesses ................. 3 0 7 V anity Mirrors ........................... 7 8 V ariance, Compass ....................... 1 2 3 V ehicle Identification Number .
デバイスJeep Liberty (2004)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jeep Liberty (2004)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJeep Liberty (2004)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jeep Liberty (2004)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jeep Liberty (2004)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jeep Liberty (2004)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJeep Liberty (2004)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jeep Liberty (2004)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJeep Liberty (2004)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
