JetメーカーDC-1100Gの使用説明書/サービス説明書
ページ先へ移動 of 20
Operating Instructions and Parts Manual Dust Collector Model: DC-1100A/C/RC DC-1100A/RC DC-1100C/RC WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been prepared fo r the owner and operators of JET DC-11 00 Series Dust Collectors. Its purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for model DC-1100 Series Dust Collectors. This manual contains instructions on inst allation, safety precaution s, general operating procedures, maintenance in structions and par ts breakdown.
7 Unpacking DC-1100A/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
8 Unpacking DC-1100C/RC Dust Collector 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
9 Assembly Base 1. Install four casters to the under side of t he base as pictured in Fig. 2. 2. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the undersi de of the base, turn until snug.
10 Connector Housing 5. Attach three support brac kets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time. 6. Install the housing (A, Fig. 5) to two support brackets (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig.
11 Filter Bag Installation – DC-1100A/RC Referring to Figure 7: 1. Place the hanger (A) on the hanger bracket (B). 2. Slide the filter bag loop (C) over the hanger hook. 3. Thread the re tainer strap (D) through the loops on the filter bag (E) and fasten to the collector housing (F).
12 Collector Bag Installation – DC-1100C/RC 1. Place the rin g over the top of the plastic bag an d fold over the bag approximately three inche s, Figure 9. 2. Insert the snap ring (A, Fig. 10) of the collector bag into the bottom of the housing at an angle.
13 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-1100A/RC and DC-110 0C/RC dust collectors are rated at 115/230V, Prewired 115V .
14 Maintenance Never perform maintenance on this machine before turning s witch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-1100A/RC Wearing a particle mask or respirator for protection against fine dust particles during cleaning is highly recommended.
15 Parts List – DC -1100A/RC Dust Collector Index No. Part No. Description Size Qty 1 ............... 411035W ................. Impe ller Hous ing ....................................................................... ..............................
16 Parts Breakdown – DC -1100A/RC Dust Collector.
17 Filter Assembly for DC-1100C/RC Models Index No. Part No. Description Size Qty 1 ............... 331050..................... Handle ....................................................................................................................
18 Remote Control Breakdown for DC-1100RC Index No. Part No. Description Size Qty ................. DC1100RC-100 ....... Receiver Assembly (Ite ms 1-12) ............................................................. ............... 1 1 ............... DCRC-101 .
19 Wiring Diagram – DC-1100A/C.
20 Wiring Diagram – DC-1100RC.
デバイスJet DC-1100Gの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jet DC-1100Gをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJet DC-1100Gの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jet DC-1100Gの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jet DC-1100Gで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jet DC-1100Gを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJet DC-1100Gの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jet DC-1100Gに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJet DC-1100Gデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
