JetメーカーDC-650Aの使用説明書/サービス説明書
ページ先へ移動 of 20
Operating Instructions and Parts Manual Dust Collector Model: DC-650A/C/ARC/CRC DC-650ARC shown DC-650C shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been pre pared for the owner and operato r s of the JET DC-650 Series Dust Collectors. I ts purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for models DC-650 Series Dust Collectors. This manual contains in structions on installation, safety pre cautions, general operating procedures, maintenance in structions and par ts breakdown.
7 Unpacking 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
8 Assembly The dust collector must be disconnected from the po wer source during assembly . Failure to comply may result in serious injury! Motor Housing and Support Canister 1. Place the impeller housing (A, Fig. 1) on the floor with the motor (B, Fig.
9 Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 fl at washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housin g and tighten nut against the housing.
10 Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig.
11 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-650 series dust collectors are rated at 115/230V, Prewired 115V .
12 Maintenance Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-650A/ARC Wearing a particle mask/respirator for protection against fin e dust particles during cleaning is highly recommended.
13 Parts Replacement Parts Replacement parts are li sted in the Parts List on the following pages. To orde r parts or reach our service department, call 1-800-274-68 48 between 7:00 a.
14 Index No. Part No. Description Size Qty 35 ............. 331010 ..................... Shaft ....................................................................................................................... 1 36 ............. 331043 ..........
15 Parts Breakdown for DC-650C/ CRC Models for DC-650A/AR C Models.
16 Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size Qty ................. DC650RC-100 ......... Rec eiver As sembly (Ite ms 1-11) ............................................................ ................ 1 1 .........
17 Wiring Diagrams DC-650A/C Models 115V 230V.
18 DC-650ARC/CRC Models.
19 Notes.
20 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
デバイスJet DC-650Aの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jet DC-650Aをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJet DC-650Aの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jet DC-650Aの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jet DC-650Aで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jet DC-650Aを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJet DC-650Aの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jet DC-650Aに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJet DC-650Aデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
