Juniper NetworksメーカーM120の使用説明書/サービス説明書
ページ先へ移動 of 116
M120 Internet Router PIC Guide Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 USA 408-745-2000 www.juniper.net Part Number: 530-024399-01, Revision 1.
This guide provides an overview and description of the Physical Interface Cards (PICs) supported by the Juniper Networks M120 Internet router. The PICs are described alphabetically. Table 1 on page 3 lists the PICs supported by the M120 Internet router by PIC family.
Table 1: PICs Supported by the M120 Internet Router Page First JUNOS Support Ports PIC Family and Type ATM2 IQ 20 8.0R2 4 ATM2 DS3 IQ 22 8.0R2 4 ATM2 E3 IQ 24 8.0R2 2 ATM2 OC3/STM1 IQ 27 8.0R2 1 ATM2 OC12/STM4 IQ 27 8.0R2 2 ATM2 OC12/STM4 IQ 30 8.0R2 1 ATM2 OC48/STM16 IQ with SFP Channelized IQ 33 8.
Table 1: PICs Supported by the M120 Internet Router (continued) Page First JUNOS Support Ports PIC Family and Type 78 8.0R2 1 10-Gigabit Ethernet DWDM 60 8.0R2 1 Gigabit Ethernet with SFP 60 8.0R2 2 Gigabit Ethernet with SFP 60 8.0R2 4 Gigabit Ethernet with SFP 60 8.
Table 1: PICs Supported by the M120 Internet Router (continued) Page First JUNOS Support Ports PIC Family and Type 91 8.0R2 1 SONET/SDH OC12c/STM4 94 8.4 1 SONET/SDH OC12/STM4 (Multi-Rate) with SFP 94 8.3 4 SONET/SDH OC12/STM4 (Multi-Rate) with SFP 99 8.
FPCs and cFPCs Supported M120 routers support the FPCs listed in Table 2 on page 6. Table 2: FPCs Supported by the M120 Router First JUNOS Release Maximum Throughput per FPC Maximum Number of PICs Supported per FPC FPC Model Number FPC Name FPC Type 8.
Table 4: Optical Interface Support for 10-Gigabit Ethernet cFPC (continued) 10-GBASE-Z 10-GBASE-E 10-GBASE-L 10-GBASE-S Parameter 9/125 SMF cable: 49.6 miles/80 km 9/125 SMF cable: 24.8 miles/40 km: Distances greater than 30 km are considered to be engineered links.
Table 5: Optical Interface Support for SONET/SDH OC192/STM64 cFPC (continued) Long Reach (LR) 2 Intermediate reach (IR) 2 Short reach (SR) 1 Parameter SMF cable: 49.71 miles/80 km SMF cable: 24.8 miles/40 km; distances greater than 30 km are considered to be engineered links.
PIC/FPC Compatibility Table 6 on page 9 provides a PIC/FPC compatibility matrix for the supported PICs for the M120 router. Table 6: M120 PIC/FPC Compatibility FPC3 FPC2 FPC1 PIC Model Number Number of Ports PIC Type ATM2 IQ PICs – – 8.0R2 PB-4DS3-ATM2 4 ATM2 DS3 IQ – – 8.
Table 6: M120 PIC/FPC Compatibility (continued) FPC3 FPC2 FPC1 PIC Model Number Number of Ports PIC Type EIA-530 PIC – – 8.0R2 PB-2EIA530 2 EIA-530 Ethernet PICs – – 8.0R2 PB-4FE-TX 4 Fast Ethernet – – 8.0R2 PB-8FE-FX 8 Fast Ethernet – – 8.
Table 6: M120 PIC/FPC Compatibility (continued) FPC3 FPC2 FPC1 PIC Model Number Number of Ports PIC Type – – 8.2R2 PB-MS-100-1 0 MultiServices 100 NOTE: This PIC requires the 710-017980 version or later of the FPC1. – 8.2 – PB-MS-400-2 0 MultiServices 400 8.
Adaptive Services II PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Supports tunnel services. This feature is included with the PIC and does not require an individual license. ■ Individual licenses must be purchased for additional services.
Table 7: Adaptive Services PICs Software Features Supported by the M120 Router Adaptive Services II Layer 2 Services PIC Adaptive Services II PIC Software Feature – – GRE Key – – GRE dont-fragment – 8.0R2 Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks – 8.
Table 7: Adaptive Services PICs Software Features Supported by the M120 Router (continued) – 8.0R2 Encapsulations: ■ Multilink Frame Relay (MLFR) ■ Multilink Point-to-Point Protocol (MLPP) 14 .
Adaptive Services II FIPS PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ JUNOS-FIPS requires an Adaptive Services II FIPS PIC for external IPSec connections. See the Secure Configuration Guide for Common Criteria and JUNOS-FIPS for more information.
For a list of the software features available for services PICs, see the JUNOS Services Interfaces Configuration Guide . Depending on your JUNOS release and individual licenses, software features for .
Adaptive Services II Layer 2 Services PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Supports Layer 2 Service package only. Tunnel services are included with the PIC. Other services require an individual license.
Table 8: Adaptive Services PICs Software Features Adaptive Services II Layer 2 Services PIC Adaptive Services II PIC Software Feature – – GRE Key – – GRE dont-fragment – 8.0R2 Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks – 8.
Table 8: Adaptive Services PICs Software Features (continued) – 8.0R2 Encapsulations: ■ Multilink Frame Relay (MLFR) ■ Multilink Point-to-Point Protocol (MLPP) Adaptive Services II Layer 2 Servi.
ATM2 DS3 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four DS3 ports ■ Power requirement: 0.41 A @ 48 V (20.0 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
■ Per-virtual circuit (VC) and per-virtual path (VP) traffic shaping ■ Unspecified bit rate (UBR) traffic shaping ■ Fine-grained variable bit rate (VBR) traffic shaping ■ Circuit cross-connect.
ATM2 E3 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four E3 ports ■ Power requirement: 0.
■ Per-virtual circuit (VC) and per-virtual path (VP) traffic shaping ■ Unspecified bit rate (UBR) traffic shaping ■ Fine-grained variable bit rate (VBR) traffic shaping ■ Circuit cross-connect.
ATM2 OC3/STM1 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Two OC3 ports ■ Power requirement: 0.41 A @ 48 V (20 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface ■ Conforms to ANSI T1.
■ Circuit cross-connect (CCC) for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or unassigned cell transmission .
Table 9: Optical Interface Support for ATM2 OC3 IQ PICs (continued) Multimode Intermediate Reach (IR) Parameter Multivendor agreement Telcordia GR-253 Standard 1.
ATM2 OC12/STM4 IQ PICs Left: 1-port ATM2 OC12/STM4 IQ PIC; Right: 2-port ATM2 OC12/STM4 IQ PIC ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Software release ■ One or two OC12 ports ■ Power requirement: ■ 1-port: 0.
■ Circuit cross-connect for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or unassigned cell transmission ■ OAM .
Table 10: Optical Interface Support for ATM2 OC12/STM4 IQ PICs (continued) Multimode Transceiver Intermediate Reach (IR) Transceiver Parameter Multivendor agreement Telcordia GR-253 Standard 546.
ATM2 OC48/STM16 IQ PIC with SFP ■ JUNOS 8.0R2 and later (Type 2) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One OC48 port ■ Power requirement: 0.41 A @ 48 V ( 20 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
■ Multiprotocol Label Switching (MPLS) circuit cross-connect for leveraging ATM access networks ■ User-configurable virtual circuit (VC) and virtual path (VP) support ■ Support for idle cell or .
Table 11: Optical Interface Support for ATM2 IQ OC48 PICs (continued) Single-Mode Intermediate Reach PIC Type Telcordia GR-253 Standard 9.3 miles/15 km Maximum distance 1274 through 1356 nm Transmitte.
Channelized DS3 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four DS3 ports ■ Power requirement: 0.
■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): DS1 MIB, DS3 M.
Channelized E1 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Ten E1 ports ■ Power requirement: 0.15 A @ 48 V (7.2 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
■ 120-ohm RJ-48C Cables and connectors One bicolor per E1 port: ■ Off — Port not enabled ■ Green — Physical E1 link is up; individual subchannels can be down ■ Red — Physical E1 link is .
Channelized OC3 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One OC3 port ■ Power requirement: 0.39 A @ 48 V (8.6 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
■ Quality of Service (QoS) per channel: weighted round-Robin (WRR), random early drop (RED), weighted random early drop (WRED) ■ Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB.
Table 12: Optical Interface Support for Channelized OC3 IQ PICs (continued) Intermediate Reach (IR) PIC Type – 15 through – 8 dBm Average launch power – 8 dBm Receiver saturation – 28 dBm Rece.
Channelized OC12 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One OC12 port ■ Power requirement: 0.
■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): OC3 MIB, DS3 M.
Table 13: Optical Interface Support for Channelized OC12 IQ PICs (continued) Intermediate Reach (IR) Parameter Telcordia GR-253 Standard 9.3 miles/15 km Maximum distance 1274 through 1356 nm Transmitt.
Channelized STM1 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One STM1 port ■ Power requirement: 0.
■ Alarm indication signal (AIS-L, AIS-P) ■ Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF) ■ Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P) ■ Errored.
Channelized T1 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Ten T1 ports ■ Power requirement: 0.15 A @ 48 V (7.2 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface.
■ Data service unit (DSU) and channel service unit (CSU) functionality ■ Ports configurable as clear channel T1 interfaces with 1.544-Mbps connectivity ■ Framing: Superframe (SF or D4) and Exten.
■ Alarm indication signal (AIS) ■ Remote defect indication (RDI) ■ Loss of frame (LOF) ■ Loss of signal (LOS) ■ Bipolar violation (BPV) ■ Excessive zero (EXZ) ■ Line code violation (LCV).
DS3 PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four DS3 ports ■ Power requirement: 0.47 A @ 48 V (22.5 W) ■ Integrated DSU interoperability with leading DSU vendors Description ■ High-performance throughput on each port at speeds up to 44.
■ DS3 functionality: ■ C-bit framing ■ B3ZS line encoding ■ DS3 diagnostics and loopback control ■ DS3 alarm and event counting and detection ■ Per-packet counts and byte counts ■ Local .
E1 PICs Left: E1 RJ-48 PIC; Right: E1 Coaxial PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Software release ■ Four E1 or coaxial ports ■ Power requirement: 0.
■ Integrated support for G.703 unframed mode and G.704 framed mode with CRC; this feature is user-configurable NOTE: The G.704 implementation supports speeds slower than 2.
E3 IQ PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four E3 ports ■ Power requirement: 0.38 A @ 48 V (18 W) ■ Intelligent queuing (IQ) PICs support fine-grained queuing per logical interface Description ■ Clear-channel (34.
■ Quality of service (QoS) per port: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Simple Network Management Protocol (SNMP): E3 MIB, QoS MIB .
EIA-530 PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Two EIA-530, X.21 or V.35 serial ports ■ Power requirement: 0.
■ Supports four queues per port ■ Random early detection (RED) ■ Transmitter Signal Element Timing is looped from the timing received on the Transmitted Signal Element DCE. EIA-530 ports support the ability to invert the Transmit Data Element. The EIA-530 ports support the following rates: ■ 2.
Fast Ethernet PICs Left: 4-Port Fast Ethernet PIC; Right: 8-Port Fast Ethernet PIC Left: 12-Port Fast Ethernet PIC; Right: 48-Port Fast Ethernet PIC 56 ■ Fast Ethernet PICs M120 Internet Router PIC .
VHDCI to RJ-21 Cable ■ 4-port: JUNOS 8.0R2 and later (Type 1) ■ 8-port: JUNOS 8.0R2 and later (Type 1) ■ 12-port: JUNOS 8.0R2 and later (Type 1) ■ 48-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1.
4-port PIC: ■ Connector: Two-pair, Category 5 unshielded twisted-pair connectivity through an RJ-45 connector ■ Pinout: MDI noncrossover 8-port PIC: ■ Connector: MT-RJ female ■ FX optical inte.
48-port PIC — does not have port LEDs. To check port status on a 48-port PIC, use the show interfaces fe- fpc / pic / port command. For more information about this command, see the JUNOS Network Interfaces Configuration Guide .
Gigabit Ethernet PICs with SFP Left: 1-Port Gigabit Ethernet PIC; Right: 2-Port Gigabit Ethernet PIC Left: 4-Port Gigabit Ethernet PIC; Right: 10-Port Gigabit Ethernet PIC 60 ■ Gigabit Ethernet PICs.
Software release ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) ■ 4-port: JUNOS 8.0R2 and later (Type 2) ■ 10-port: JUNOS 8.0R2 and later (Type 3) NOTE: These PICs are not supported in JUNOS Release 8.1R1. ■ One, two, four, or ten Gigabit Ethernet ports ■ Power requirement: ■ 1-port: 0.
Status LED, one bicolor: ■ Off — PIC is not enabled ■ Green — PIC is operating normally ■ Red — PIC has an error or failure Port LEDs, one pair per port: ■ Link — If green, the port is.
Gigabit Ethernet IQ PICs with SFP Left: 1-port Gigabit Ethernet IQ PIC; Right: 2-port Gigabit Ethernet IQ PIC ■ 1-port: JUNOS 8.0R2 and later (Type 1) ■ 2-port: JUNOS 8.0R2 and later (Type 2) NOTE: These PICs are not supported in JUNOS Release 8.1R1.
■ You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions .
Table 16: Optical Interface Support for Gigabit Ethernet IQ PICs with SFP (continued) 1000Base-LH 1000Base-LX 1000Base-SX Parameter – 20 through – 3 dBm – 19 through – 3 dBm – 17 through 0 d.
Gigabit Ethernet IQ2 PICs with SFP Left: 4-port Gigabit Ethernet IQ2 PIC (Type 1); Right: 8-port Gigabit Ethernet IQ2 PIC (Type 2) 66 ■ Gigabit Ethernet IQ2 PICs with SFP M120 Internet Router PIC Gu.
g002378 Center: 8-port Gigabit Ethernet IQ2 PIC (Type 3) ■ 4-port: JUNOS 8.0R2 and later (Type 1) ■ 8-port: JUNOS 8.0R2 and later (Type 2) ■ 8-port: JUNOS 8.5 and later (Type 3) NOTE: These PICs are not supported in JUNOS Release 8.1R1. Software release ■ Four or eight Gigabit Ethernet ports ■ Power requirement: ■ 4-port: 0.
■ Intelligent handling of oversubscribed traffic for Type 1 and Type 2 PICs ■ Optical diagnostics and related alarms ■ Quality of service (QoS) per channel: weighted round-robin (WRR), random ea.
Table 17: Optical Interface Support for Gigabit Ethernet IQ2 PICs with SFP 1000Base-LH 1000Base-LX 1000Base-SX Parameter Single-mode Single-mode Multimode Optical interface SFP SFP SFP Transceiver type Multivendor agreement IEEE 802.3 — 1998 IEEE 802.
10-Gigabit Ethernet IQ2 PIC with XFP ■ JUNOS 8.2 and later (Type 3) Software release ■ One 10-Gigabit Ethernet port ■ Power requirements: 1.2 A @48 V (56 W) Description ■ High-performance throughput ■ WAN-PHY mode at 9.953 Gbps ■ LAN-PHY mode at 10.
■ Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) ■ Configurable WAN-PHY mode options: ■ loopback ■ mpls .
Table 18: Optical Interface for 10-Gigabit Ethernet IQ2 PICs 10-GBase-Z 10-GBase-E 10-GBase-L 10-GBase-S Parameter XFP-10G-Z-OC192-LR2 XFP-10G-E-OC192-IR2 XFP-10G-L-OC192-SR1 XFP-10G-S Transceiver model number Single-mode Single-mode Single-mode Multimode Optical interface XFP XFP XFP XFP Transceiver type Multivendor agreement IEEE 802.
10-Gigabit Ethernet PIC with XENPAK ■ 10-Gigabit Ethernet PIC with XENPAK: JUNOS 8.0R2 and later (Type 3) ■ XENPAK-OTN transceivers: JUNOS 9.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One 10-Gigabit Ethernet port ■ Power requirement: 0.
■ Duplex SC/PC connector (RX and TX) ■ Optical interface support — See Table 19 on page 74 and Table 20 on page 75 Cables and connectors Status LED, one bicolor: ■ Off — PIC not enabled ■ .
Table 19: Optical Interface Support for 10-Gigabit Ethernet PICs with XENPAK (continued) Extra-Long Wavelength Serial (10GBase-ZR), LAN Rate Extra-Long Wavelength Serial (10GBase-ER), LAN Rate Long Wavelength Serial (10GBase-LR), LAN Rate Short Wavelength Serial (10GBase-SR), LAN Rate Parameter – 24.
Table 20: Optical Interface Support for 10-Gigabit Ethernet PICs with XENPAK-OTNs (continued) ■ Transmitter type: Electro-absorption Modulated Laser (EML) ■ Modulation format: Non-retum-to-zero (NRZ) ■ Channel-plan wavelength range: 1551.72 through 1542.
Table 21: XENPAK-OTN Optical Signal-to-Noise Ratio (OSNR) Performance (continued) CD Tolerance (ps/nm) Input-Power Range (dBm) Post-FEC BER Pre-FEC BER FEC Type OSNR (dB/0.
10-Gigabit Ethernet DWDM PIC ■ JUNOS 8.0R2 and later (Type 3) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One 10-Gigabit Ethernet port ■ Power requirement: 0.
■ Enhanced optical monitoring capabilities ■ CLI configurable wavelength support ■ Virtual Router Redundancy Protocol (VRRP) support ■ 802.1q virtual LANs (VLANs) support ■ 802.
MultiServices PICs Left: MultiServices 100 PIC; Right: MultiServices 400 PIC Center: MultiServices 500 PIC Software release 80 ■ MultiServices PICs M120 Internet Router PIC Guide.
■ MultiServices 100: JUNOS 8.2R2 and later (Type 1) NOTE: This PIC requires the 710-017980 version of the FPC1. ■ MultiServices 400: JUNOS 8.2 and later (Type 2) ■ MultiServices 500: JUNOS 8.3 and later (Type 3) ■ Supports tunnel services. This feature is included with the PIC and does not require an individual license.
Table 24: MultiServices PICs Software Features Supported on the M120 Router (continued) 8.3 8.2 8.2R2 Stateful firewall with packet inspection: detects SYN attacks, ICMP and UDP floods, and ping-of-death attacks 8.3 8.2 8.2R2 Network Address Translation (NAT) for IP addresses 8.
SONET/SDH OC3c/STM1 PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: Although the illustration shows a multimode PIC, a multimode PIC and a single-mode intermediate reach PIC are both supported. NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four OC3 ports ■ Power requirement: 0.
■ Duplex SC/PC connector (Rx and Tx) ■ Optical interface support — See Table 25 on page 85 NOTE: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device.
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 25: Optical Interface Support for SONET/SDH OC3c/STM1 PICs (continued) Multimode Intermediate Reach Parameter Multivendor agreement Telcordia GR-253 Standard MMF cable: 1.
SONET/SDH OC3/STM1 (Multi-Rate) PICs with SFP POR T 3 Left: SONET/SDH OC3/STM1 (Multi-Rate) PIC (Type 1); Right: SONET/SDH OC3/STM1 (Multi-Rate) PIC (Type 2) ■ 4-port: JUNOS 8.
■ Optical diagnostics and related alarms ■ Per-port SONET/SDH framing ■ Link aggregation ■ Alarm and event counting and detection ■ Dual-router automatic protection switching (APS) ■ Multi.
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 26: Optical Interface Support for SONET/SDH OC3/STM1 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Long Reach (LR-1) Intermediate Reach (IR-1) Multimode Parameter Single-mode Single-mode Multimode Optical interface SFP SFP SFP Transceiver type SMF cable: 24.
SONET/SDH OC12c/STM4 PIC ■ JUNOS 8.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ One OC12 port ■ Power requirement: 0.
One tricolor per port: ■ Off — Not enabled ■ Green — Online with no alarms or failures ■ Amber — Online with alarms for remote failures ■ Red — Active with a local alarm; router has de.
Table 28: Optical Interface Support for SONET/SDH OC12c/STM4 PICs Multimode Intermediate Reach Parameter Multimode Single-mode Optical interface Fixed Fixed Transceiver type Multivendor agreement Telcordia GR-253 Standard MMF cable: 546.8 yards/500 m SMF cable: 9.
SONET/SDH OC12/STM4 (Multi-Rate) PICs with SFP Left: 1-port SONET/SDH OC12/STM4 (Multi-Rate) PIC; Right: 4-port SONET/SDH OC12/STM4 (Multi-Rate) PIC ■ 1-port: JUNOS 8.
■ Optical diagnostics and related alarms ■ Per-port SONET/SDH framing ■ Link aggregation ■ Alarm and event counting and detection ■ Dual-router automatic protection switching (APS) ■ Multi.
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 29: Optical Interface Support for SONET/SDH OC12/STM4 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Long Reach (LR-1) Intermediate Reach (IR-1) Multimode Parameter Single-mode Single-mode Multimode Optical interface SFP SFP SFP Transceiver type SMF cable: 24.
Table 31: Optical Interface Support for SONET/SDH OC12/STM4 (Multi-Rate) PICs Configured at an OC48/STM16 Rate (continued) Long Reach (LR-2) Intermediate Reach (IR-1) Short Reach (SR-1) Parameter SFP SFP SFP Transceiver type SMF cable: 49.71 miles/80 km SMF cable: 9.
SONET/SDH OC48c/STM16 PIC with SFP ■ JUNOS 8.0R2 and later NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four OC48 ports ■ Power requirement: 0.
You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions .
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 32: Optical Interface Support for SONET/SDH OC48c/STM16 PICs with SFP (continued) Long Reach (LR) Intermediate Reach (IR) Short Reach (SR) Parameter SMF cable: 49.71 miles/80 km SMF cable: 9.3 miles/15 km SMF cable: 1.24 miles/2 km Maximum distance Telcordia GR-253 — L-16.
SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP ■ JUNOS 8.3 and later (Type 2) Software release ■ Rate-selectable using one of the following rates: ■ 1-port OC3c ■ 1-port OC12 ■ 1-port OC12c ■ 1-port OC48 ■ 1-port OC48c ■ Power requirement: 0.
You can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions .
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 33: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC3/STM1 Rate (continued) Long Reach (LR-1) Intermediate Reach (IR-1) Multimode Parameter Single-mode Single-mode Multimode Optical interface SFP SFP SFP Transceiver type SMF cable: 24.
Table 35: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC48/STM16 Rate (continued) Long Reach (LR-2) Intermediate Reach (IR-1) Short Reach (SR-1) Parameter SFP SFP SFP Transceiver type SMF cable: 49.71 miles/80 km SMF cable: 9.
SONET/SDH OC192c/STM64 PIC with XFP ■ JUNOS 8.3 and later (Type 3) Software release ■ One OC192 port ■ Power requirement: 0.52A @ 48 V (25 W) Description ■ Multiplexing and demultiplexing ■ .
■ Duplex LC connector (Rx and Tx) ■ Optical interface support — See Table 36 on page 110 NOTE: To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device.
■ SONET alarms: ■ Alarm indication signal — line (AIS-L) ■ Alarm indication signal — path (AIS-P) ■ Bit error rate signal degrade (BERR-SD) ■ Bit error rate signal fail (BERR-SF) ■ Bit.
Table 36: Optical Interface Support for SONET/SDH OC192 PICs (continued) Long Reach (LR-2) Intermediate Reach (IR-2) Short reach (SR-1) Parameter XFP XFP XFP Transceiver type Telcordia GR-253 OC192 LR2 Telcordia GR-253 OC192 IR2 Telcordia GR-253 OC192 SR1 Standard SMF cable: 49.
T1 PIC ■ JUNOS 8.0R2 and later (Type 1) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Four T1 ports ■ Power requirement: 0.
■ Alarm indication signal (AIS) ■ Bipolar violations ■ Excessive zeros ■ Far-end block errors (FEBE, E-bit errors) ■ Loss of frame (LOF), Loss of signal (LOS) ■ Yellow alarm bit (X-bit) di.
Tunnel Services PIC ■ JUNOS 8.0R2 and later (Type 1, Type 2, and Type 3) NOTE: This PIC is not supported in JUNOS Release 8.1R1. Software release ■ Power requirement: 0.
Appendix A High Availability Features High availability features include Routing Engine redundancy, graceful Routing Engine switchover (GRES), nonstop bridging, nonstop active routing, graceful restart for routing protocols, Virtual Router Redundancy Protocol (VRRP), and unified in-service software upgrade (ISSU).
Copyright © 2008, Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. JUNOS and JUNOSe are trademarks of Juniper Networks, Inc.
デバイスJuniper Networks M120の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Juniper Networks M120をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJuniper Networks M120の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Juniper Networks M120の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Juniper Networks M120で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Juniper Networks M120を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJuniper Networks M120の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Juniper Networks M120に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJuniper Networks M120デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。