JuraメーカーImpressa F50 Classicの使用説明書/サービス説明書
ページ先へ移動 of 33
I M IM PR E SSA PRE SSA F5 0 / F 50 5 F50 / F505 In st ru c t io n s for u se Instructions for use.
2 Legend: 䡲 DISPLAY: serves as information. 䡲 DISPLAY: please follow the instructions shown. = Note / Tip = Important.
3 Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig.17 Fig. 5 Fig. 16 Temp. max. Temp. min. Fig.
10 9 13 14 17 18 11 3 1 2 12 20 4 7 8 5 6 15/16 19 Rotary Switch 13 21 22 4 Control elements 1. Rotary Switch 2. Illuminated ring 3. Maintenance button 4. Preparation button, 1 espresso 5. Preparation button, 2 espressi 6. Preparation button, 1 coffee 7.
5 E T able of contents 1. Safety instructions ............................................... page 6 1.1 Proper use .................................................. page 6 1.2 Warnings .................................................... page 6 1.3 Precautions .
6 Before y ou get star ted Congratulations on purchasing this IMPRESSA. To ensure that your IMPRESSA works smoothly, please read these instructions for use carefully and keep them as a future reference.
7 䡲 Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges. 䡲 Always remove the mains plug during long periods of absence (holidays etc.). 䡲 Always remove the mains plug before cleaning. 䡲 When removing the mains plug, never tug the supply cable or the IMPRESSA itself.
8 Only use the switch to adjust the consistency of grind when the grinder is running. 䡲 Open the bean container cover (12) and remove the aroma preser- vation cover (13). 䡲 To adjust the consistency of grind, turn the switch to the desired position during the grinding operation (Fig.
9 The IMPRESSA is set to 16° dH by default. You can change this setting. Proceed as follows: 䡲 READY 䡲 Press and hold the Rotary Switch (1) until RINSE appears on the dis- play.
10 You can interrupt rinsing of the filter at any time by closing the steam / hot water draw-off tap (14). To continue with filter rins- ing, open the steam / hot water draw-off tap (14) again. 䡲 CLOSE TAP 䡲 Close the steam / hot water draw-off tap (14), your IMPRESSA will now heat up to coffee temperature.
11 7 . A djusting the amount of wa ter for co ffee The figure in ML is approximate and may vary from the actual amount. The machine automatically doubles the amount of water pro- grammed for the 2 espressi / 2 coffees preparation but- tons. You can also change the amount of water during operation.
12 䡲 䡵䡵䡵䡺䡺䡺䡺䡺䡺䡺 䡲 Your speciality coffee is prepared. 䡲 1 COFFEE 䡲 READY 9. Preparing 2 cups of coff ee The strength cannot be selected when preparing 2 cups of cof- fee. You automatically prepare 2 mild cups. You can stop preparation prematurely by pressing any prepara- tion button.
13 䡲 Select the 1 coffee preparation button (6) or 2 coffees prepara- tion button (7). 䡲 1 COFFEE 䡲 䡵䡵䡵䡺䡺䡺䡺䡺䡺䡺 䡲 The illuminated ring (2) is active. 䡲 By turning the Rotary Switch (1), you can individually select the amount of water for coffee: 䡲 For example 110 ML.
14 䡲 READY 䡲 Press the steam preselection button (8). 䡲 HEATING 䡲 READY 䡲 Open the steam / hot water draw-off tap (14) (Fig. 13) to draw off steam.
15 䡲 Insert the other end of the milk pipe into a milk carton or connect it to a milk container (Fig. 7). 䡲 Place a cup under the Professional Cappuccino Frother (Fig. 7). The high-quality stainless steel container is a practical addition for all lovers of milk specialities.
16 1 3. 3 Rinsing the Professional Cappuccino F rother To ensure that the Professional Cappuccino Frother (15) works perfectly, you should rinse it with water after every milk prepa- ration. Your IMPRESSA will not prompt you to rinse the Professional Cappuccino Frother.
17 䡲 Open the steam / hot water draw-off tap (Fig. 13) to draw off steam. 䡲 STEAM 䡲 䡵䡵䡵䡺䡺䡺䡺䡺䡺䡺 䡲 Ignoring the CLOSE TAP display message, draw off steam until the receptacle containing JURA Cappuccino Cleaner is empty. The Professional Cappuccino Frother and the milk pipe are cleaned.
18 Rotary Switch Permanent settings in programming mode always follow the same model. To enter programming mode, press the Rotary Switch (1) until RINSE appears on the display. By turning the Rotary Switch (1) you can change the set values and select dif- ferent programme items.
19 15. 1 Buttons programme item With the BUTTONS programme item you can enter individual settings for all speciality coffees, milk and hot water. Permanent settings in programming mode always follow the same model.
20 䡲 Turn the Rotary Switch (1) to adjust the temperature. 䡲 HIGH 䡲 Press the Rotary Switch to confirm your selection. 䡲 OK 䡲 TEMP. 䡲 Turn the Rotary Switch (1) until EXIT appears on the display. 䡲 Press the Rotary Switch (1). 䡲 SELECT BUTTON 䡲 Turn the Rotary Switch (1) again until EXIT appears on the display.
21 䡲 Press and hold the Rotary Switch (1) until RINSE appears on the dis- play. 䡲 The illuminated ring (2) is active. 䡲 Press the Rotary Switch (1) until you reach the OFF AFTER pro- gramme item. 䡲 OFF AFTER 䡲 Press the Rotary Switch (1) to enter the OFF AFTER programme item.
22 䡲 RESET ALL All customer settings are reset to the factory settings. The IMPRESSA then switches off. For example you want to reset the values for one product to the fac- tory setting: 䡲 READY 䡲 Press and hold the Rotary Switch (1) until RINSE appears on the dis- play.
23 䡲 Press the 1 COFFEE preparation button. 䡲 XXXX (=total number for ‘1 COFFEE’) 䡲 Press the Rotary Switch (1) to exit the programme item. 䡲 BUTTONS Turn the Rotary Switch (1) for more information about the filter, descaling or the machine version.
24 15. 10 Language programme item You can choose from the following languages: German Dutch English Spanish French Portuguese Italian Russian 䡲 READY 䡲 Press and hold the Rotary Switch (1) until RINSE appears on the dis- play. 䡲 The illuminated ring (2) is active.
25 16. 3 Drip tray missing 䡲 TRAY MISSING 䡲 When this display lights up, the drip tray (20) has not been cor - rectly inserted or has not been inserted at all. 䡲 Insert the drip tray (20). 䡲 READY 16.4 Filling with coffee beans 䡲 FILL BEANS 䡲 Top up the beans as described in chapter 2.
26 䡲 To ensure that the Professional Cappuccino Frother always works properly, you should clean it daily when you have been preparing milk. 䡲 The water tank should be rinsed daily and filled with fresh water. If you can see scale starting to form in the water tank, you can use a conventional descaling agent to remove it.
27 䡲 Place a 1 litre receptacle (Fig. 12) under the height-adjustable coffee spout (17). 䡲 PRESS RINSE 䡲 Press the Maintenance button (3). 䡲 CLEANING 䡲 ADD TABLET 䡲 Add the tablet to the powder shaft (Fig. 15). Close the powder shaft. 䡲 PRESS RINSE 䡲 Press the Maintenance button (3).
28 䡲 TRAY MISSING 䡲 Carefully reinsert the drip tray. 䡲 AGENT IN TANK Remove and empty the water tank. Completely dissolve the contents of one blister (3 tablets) in 0.5 litres of water and add the mixture to the water tank. Reinsert the water tank.
29 20. Tips for a perfec t coffee Height-adjustable coffee spout (17) You can adjust the coffee spout to the size of your cups (Fig. 3). Consistency of grind For details, please refer to chapter 2.5 ‘Adjusting the grinder’ Prewarming cups You can prewarm the cups with hot water or steam.
30 21. Messages Cause Remedy FILL WATER TANK The water tank is empty Fill the water tank The float is defective Rinse or descale the water tank FILL BEANS The bean container is empty Fill with beans Even though the beans have been topped up, the Prepare a cup of coffee.
31 E 22. Problems Problem Cause Remedy Very loud grinder noise Foreign object in grinder Coffee preparation with preground powder still possible Have IMPRESSA checked by JURA customer support Too litt.
32 23. Legal information These instructions for use contain the information required to cor- rectly use, operate and maintain the machine. The information in these instructions for use must be read and fol- lowed to ensure safe usage, operation and maintenance.
Art. 69008 – 201002 JURA Elektroapparat e AG – K affeew eltstrasse 10 – CH-4626 Niederbuchsiten Phone +41 62 389 82 33 – F ax +4 1 62 389 83 94 – www .
デバイスJura Impressa F50 Classicの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Jura Impressa F50 Classicをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJura Impressa F50 Classicの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Jura Impressa F50 Classicの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Jura Impressa F50 Classicで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Jura Impressa F50 Classicを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJura Impressa F50 Classicの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Jura Impressa F50 Classicに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJura Impressa F50 Classicデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
