JVCメーカーGD-V4211PCEの使用説明書/サービス説明書
ページ先へ移動 of 40
1 ENGLISH INSTRUCTIONS Model GD-V4210PZW GD-V4210PZW -G GD-V4210PCE GD-V4210PCE-G GD-V4211PCE Thank you f or purchasing this JVC Monitor . Before using the monitor , read this manual carefully so that you kno w how to use the Monitor correctly . Refer to this manual whenever questions or problems about operation arise.
2 Safety Precautions FCC NOTICE ■ GD-V4210PZW / GD-V4210PZW -G / GD-V4210PCE / GD-V4210PCE-G CAUTION: Changes or modifications not approv ed by JVC could v oid the user’ s authority to operate the equipment.
3 ENGLISH – When the product is used on a car t, care should be taken to a void quic k stops, e xcessiv e force , and une ven surf aces which may cause the product and car t to ov er tur n, damaging equipment or causing possible injury to the operator .
4 Parts Identification Remote Control DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT ID 17 8 9 p q 2 4 3 5 6 6 MENU/EXIT button Use this button to display or erase menus.
5 ENGLISH Monitor: Front View 1 Remote sensor/power lamp Point the front end of the wir eless remote control towar d here. When the Monitor is turned on, the power lamp glows green. It glows orange in standby mode. 2 Self-diagnostic lamps (page 37) These lamps light/flash if something abnormal occurs with the Monitor .
6 Parts Identification (Continued) Monitor: Rear Views 1 AUDIO output terminal (pin jack) (page 12) Connect these terminals to the audio input terminals of external equipment such as an amplifier . 2 REMOTE 1 (RS232C) terminal (D-sub, 9-pin) (page 12) Connect this terminal to the RS-232C terminal of a personal computer .
7 ENGLISH 8 RGB B input/output terminals (page 12) • R, G, B, HD/Cs , VD input ter minals (BNC) Connect these terminals to the following output terminals of a personal computer or other equipment: .
8 Parts Identification (Continued) q VIDEO A terminals (page 13)* • Video input terminal (BNC) Connect this terminal to the video output terminal of a VCR, etc. • Video output terminal (BNC) Connect this terminal to the video input terminal of another Monitor .
9 ENGLISH Preparations Checking the Accessories The following accessories are included with the Monitor . Check for them. If any item is missing, please contact the dealer where you purchased the Monitor . • Remote control (RM-C575) x 1 • Remote control cable x 1 • Power cord x 3 (Use the one matching the wall outlet.
10 Installation Precautions • When mounting the Monitor vertically , it is necessary to adjust the cooling fan speed to provide better heat dissipation.
11 ENGLISH Precautions • Before making connections, turn off all the equipment. • Plugs should be firmly inserted; poor connection could cause noise. • T o unplug a cord, be sur e to grasp its plug and pull it out. • Connect the power cord after having finished all other connections.
12 Connection Examples Connections (Continued) RGB connections DISPLAY ASPECT POWER RGB COMPO. VIDEO B VOLUME MULTIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UN.
13 ENGLISH A V connections These terminals are not available for GD-V4210PCE, GD-V4210PCE-G, and GD-V421 1PCE. T o use them, you need to install video interface kit (IF-C421P1W), which is separately purchased.
14 Basic Operations Daily Operations 1 T ur n on the main power . Set MAIN POWER on the back of the Monitor to ON. The POWER lamp on the upper left of the fr ont panel glows orange. 2 T ur n on the power . Press POWER on the r emote contr ol to turn the power on.
15 ENGLISH Changing the Aspect Ratio Precautions for using the screen mode switching function • This Monitor features a screen mode switching (aspect ratio change) function. If you select a mode differ ent in aspect ratio from softwar e such as TV programs, the picture may look differ ent from original pictur e.
16 Video Adjustments For video adjustments, use menus. Y ou can use the buttons either on the remote control or on Monitor for menu operations. • Refer also to “Menu Classifications” on pages 33 and 35. Adjusting the Picture Quality Picture quality can be set for each input mode.
17 ENGLISH T o make an adjustment while viewing the adjustment bar After step 3 on page 16, proceed as follows: 1 Press 5 / ∞ to move the cursor ( 3 ) to “sub menu.” 2 Press 3 to display the Sub Menu. The Sub Menu for CONTRAST appears on the screen.
18 Video Adjustments (Continued) MENU/EXIT VOLUME – 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT ID 5 Press 2 / 3 to adjust the selected item.
19 ENGLISH Adjusting the Color T emperature The adjusted setting applies to all inputs. 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. 2 Press 5 / ∞ to move the cursor ( 3 ) to “FUNCTION SELECT .” 3 Press 3 to display the Function Selection Menu.
20 Video Adjustments (Continued) MENU/EXIT 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT .
21 ENGLISH Changing the Aspect Ratio The setting adjusted applies to all inputs. • Y ou can change the aspect ratio by pr essing ASPECT . (See page 15.) 1 Pr ess MENU/EXIT (or MENU on the Monitor) to display the Main Menu. 2 Pr ess 5 / ∞ to move the cursor ( 3 ) to “FUNCTION SELECT .
22 Setting the Receivable Signal T ypes Y ou can set the receivable signal types. Normally , select “AUTO.” A common setting will apply to both VIDEO A and B terminals, and a differ ent setting will apply to the COMPONENT terminals. 1 Pr ess MENU/EXIT (or MENU on the Monitor) to display the Main Menu.
23 ENGLISH Setting the RGB Input After connecting the playback device such as a PC to the RGB terminals, you have to specify which terminal you have connected the device to — RGB A (D-sub 15 pin) or RGB B (BNC) input. • W ithout setting the RGB input correctly , you cannot show any picture though you select the RGB input.
24 Other Convenient Functions MENU/EXIT VOLUME – 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT ID PICTURE ADJ.
25 ENGLISH Setting the Auto Sleep Function This function allows you to turn of f (into standby mode) automatically when no signal comes in for a certain period of time. • The power lamp flashes (orange) while in the Sleep mode (standby). • When signals come in while in the Sleep mode, the Monitor turns on (the power lamp glows green).
26 Other Convenient Functions (Continued) MENU/EXIT VOLUME – 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 .
27 ENGLISH 2 Press 5 / ∞ to move the cursor ( 3 ) to “ST A TUS DISPLA Y .” • The Setup Menu consists of two pages. If you keep pressing 5 / ∞ , you can move to the other page fr om the current page. 3 Press 2 / 3 to select the desired setting.
28 Other Convenient Functions (Continued) MENU/EXIT VOLUME – 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT ID 2 Pr ess 5 / ∞ to move the cursor ( 3 ) to “PIXEL SHIFT” (on the second page).
29 ENGLISH Preventing the Afterimage Effect After showing the same still picture on the scr een, reverse the color on the screen using this function so that you can avoid the screen fr om being burned in with the still picture. 1 On the remote contr ol: Press MENU/EXIT while holding VOLUME – to display the Setup Menu.
30 MENU/EXIT VOLUME – 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO. VIDEO B VOLUME MUL TIPLE MODE ID SET MONITOR ADJUSTMENT VIDEO A MUTING MENU/EXIT RM-C575 REMOTE CONTROL UNIT ID Other Convenient.
31 ENGLISH Serial Connections and Operations When the Monitors are serially connected, you can contr ol all of them at the same time (simultaneous operation) or control them one by one separately (individual operation). For individual operation, you have to assign an ID number to each of the Monitors.
32 • When performing simultaneous or individual operation, use the remote contr ol. MENU/EXIT MODE ID +/– 2 / 3 5 / 5 DISPLA Y ASPECT POWER RGB COMPO.
33 ENGLISH Menu Classifications Main Menu PICTURE ADJ. SIZE/POSITION ADJ. FUNCTION SELECT STATUS DISPLAY ENTER: MAIN MENU SELECT: EXIT: MENU COLOR TEMP.
34 Menu Classifications (Continued) PICTURE ADJ. (Picture adjustment): See page 16. CONTRAST Adjusts the contrast of the picture. BRIGHT Adjusts the brightness of the picture. CHROMA*** Adjusts the color density of the picture. PHASE* Adjusts the color phase.
35 ENGLISH Setup Menu Are you sure? "YES" then press key. "NO" then press key MENU all reset R GAIN G GAIN B GAIN sub menu reset ADJUST: WHITE BALANCE:HIGH SELECT: EXIT: MENU : 000 : 001 : 002 White Balance Adjustment Menu : 000 R GAIN :+001 G GAIN :–002 B GAIN + – + – + – Are you sure? "YES" then press key.
36 • Is the power cor d disconnected? •Is the MAIN POWER switch turned on? •Is the correct input selected? •Are the devices connected correctly? •Are signals being supplied from the connected devices? •Is RGB INPUT set correctly if using the RGB terminals? •Are input signals (scanning fr equency , etc.
37 ENGLISH Self-diagnostic Indication The screen monitor may automatically turn of f and self-diagnostic lamps next to the power lamp may light or flash. When something abnormal occurs with the Monitor , this function informs you of the condition of the Monitor with self- diagnostic lamps, allowing for smooth service work.
38 Specifications General * 1 * 1 * 1 * 1 * 1 * 1 * 1 * 1 * 1 * 1 Model name GD-V4210PZW / GD-V4210PZW -G GD-V4210PCE / GD-V4210PCE-G / GD-V4211PCE Frame color GD-V4210PZW: Silver GD-V4210PCE / GD-V42.
39 ENGLISH Model name GD-V4210PZW / GD-V4210PZW -G GD-V4210PCE / GD-V4210PCE-G / GD-V4211PCE RGB A RGB input D-sub 3-row 15-pin terminal x 1, Video signal: 0.7 V(p-p), 75 Ω Sync signal: TTL lev el RGB B RGB input BNC terminal x 5 (Br idge connection possib le, auto termination) Analog RGB: R: 0.
40 Specifications (Continued) Pin assignment (Specifications for terminals) • Y/C terminal • RS-232C terminal This is a female type connector . 1 2 3 4 Pin number Signal name 1 GND (Y) 2 GND (C) 3.
デバイスJVC GD-V4211PCEの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC GD-V4211PCEをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC GD-V4211PCEの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC GD-V4211PCEの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC GD-V4211PCEで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC GD-V4211PCEを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC GD-V4211PCEの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC GD-V4211PCEに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC GD-V4211PCEデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
