JVCメーカーGR-FXM39の使用説明書/サービス説明書
ページ先へ移動 of 28
1 INSTRUCTIONS ENGLISH L YT1060-001B AUTOMA TIC DEMONSTRA TION Automatic Demonstration takes place when “DEMO MODE” is set to “ON” (factory-preset). • Available when the Power Switch @ is set to “ ” or “ ” while pressing down the Lock Button ! located on the switch.
2 PROVIDED ACCESSORIES AP-V13E, AP-V12EG or AP-V1 1E • Battery Pack BN-V1 1U • Cable Adapter • Shoulder Strap • Lens Cap • Power Cord • A/V (Audio/Video) Cable • S-Video Cable (GR-SXM49/SX25 only) NOTE: In order to maintain optimum performance of the camcorder , provided cables may be equipped with one or more core filter .
3 SAFETY PRECAUTIONS PRECAUTIONS W ARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTIONS • T o prevent shock, do not open the cabinet. No user serviceable parts inside. Refer servicing to qualified personnel.
4 When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper , or cloth etc.
5 INDEX A AC Adapter ................................................................. pg. 6 Animation Recording ................................................ pg. 21 Auto Date Record .................................................... pg. 21 Auto Focus .
6 GETTING ST ARTED Hook on. Push in. BA TTERY RELEASE Switch Battery pack Power Switch T o DC IN connector T o AC outlet AC Adapter CHARGING THE BA TTER Y P ACK 1) Hook the end of the battery pack to the camcorder and push the battery in until it locks in place.
7 • The following steps have the same function as “ REFRESH ” ( pg. 6). 1. Attach the battery to the camcorder with no cassette inserted. 2. Set the Power Switch @ to “ ” or “ ” while pressing down the Lock Button ! located on the switch.
8 ( u u ( Grip Adjustment 1) Separate the V elcro strip. 2) Pass your right hand through the loop and grasp the grip. 3) Adjust so that your thumb and fingers can easily operate the Recording Start/Stop Button 0 and Power Zoom Lever 3 . Refasten the V elcro strip.
9 1 R 4 2 B 2 E 4 5 5 R 0 C 4 M . I M I C 1 G I S N O 2 H N P N . T S G 0 – R 2 – L V P A A I H A T – G S U U – H S L – S T R E A – – E T – E C I 1 – T O 1 – N : 6 1 S 4 – T + M .
10 1 • MENU Wheel [ – , +] ................................ pg. 18 • BRIGHT Wheel [ – , +]* 1 ........................... pg. 1 1 • Speaker V olume Control [VOL.]* 1 ........... pg. 1 1 • TRACKING Wheel [ – , +] .............
11 RECORDING Set REC MODE, S-VHS (S-VHS ET)**, T APE LENGTH and DA TE/TIME in SYSTEM MENU. ( pg. 18 – 22, “ MENU SETTINGS ” ) 1 Remove the lens cap. Set the Power Switch @ to “ ” or “ ” while pressing down the Lock Button ! located on the switch.
12 BASIC FEA TURES Snapshot (GR-SXM49/SX25 only) Y ou can record still images that look like photographs onto a tape. 1) Perform step 1) of “ RECORDING ” ( pg. 1 1). 2) Press SNAPSHOT 2 . • There is a momentary camera shutter-type blackout together with the sound effect of a shutter closing.
13 Video Light (GR-SXM49/FXM39 3/SX25 only) T o brighten the scene when natural lighting is too dim. Pressing LIGHT # changes the V ideo Light mode sequentially as shown below . OFF : T urns off the light. AUTO : Automatically turns on the light when the camcorder senses insufficient lighting on the subject.
14 T racking Eliminates noise bars that appear on-screen during playback. T o activate Manual T racking: 1) Press the TRACKING Wheel 1 for approx. 2 seconds. “ MT ” z appears. 2) Rotate the TRACKING Wheel 1 so that the noise bars disappear . • T o return to Auto T racking, press the TRACKING Wheel 1 for approx.
15 Connections T o A TV/VCR 1) Make sure all units are turned off. 2) Connect the camcorder to a TV or VCR. If using both TV and VCR, connect the VCR output to the TV input. 3) T urn on all units. Set the VCR to its AUX input mode, and set the TV to its VIDEO mode.
16 Using The Cassette Adapter (optional) Use this to play back an S-VHS-C/VHS-C video cassette recorded with this camcorder on a S-VHS/ VHS VCR. 1) Slide the battery cover up to remove it, install one “ AA (R6) ” size battery , then reattach the cover .
17 INSTRUCTIONS 1 R 4 2 B 2 E 4 5 5 R 0 C 4 M . I M I C 1 G I S N O 2 H N P N . T S G 0 – R 2 – L V P A A I H A T – G S U U – H S L – S T R E A – – E T – E C I 1 – T O 1 – N : 6 1 .
18 3 Press the MENU Wheel 1 in to display the Setting Menu and rotate it to select the desired setting. 4 Press the MENU Wheel 1 in. The Menu Screen reappears with the highlight bar on “ 4 RETURN ” . Press the MENU Wheel 1 in. The normal screen reappears.
19 M.W .B. If the white balance is correct, all other colours will be accurately reproduced. AUTO : White balance is adjusted automatically . FINE : Outdoors on a sunny day . CLOUD : Outdoors on a cloudy day . HALOGEN : A video light or similar type of lighting is used.
20 SYSTEM MENU This Menu Screen cannot be accessed while recording. REC MODE Allows you to set the recording mode. “ LP ” (Long Play) is more economical, providing twice the recording time. • If the recording mode is switched during recording, the playback picture will be blurred at the switching point.
21 T APE LENGTH Allows you to set the tape length depending on the tape used: T30=30 minutes, T45=45 minutes, T50=50 minutes, T60=60 minutes. • T ape remaining time W is correct only if the correct tape length has been selected. DISPLA Y FULL: Makes all of the indications appear on the LCD monitor*/viewfinder during playback or recording.
22 LCD BRIGHT (Applicable models only) T o adjust the brightness of the LCD monitor , perform the following steps quickly (within approx. 1 second by each interval): 1) Select “LCD BRIGHT” in SYSTEM MENU. The “BRIGHT ON” message appears. 2) Press the BRIGHT Wheel 1 in to return to normal screen.
23 ADV ANCED FEA TURES Night-Scope (GR-SXM49/SX25 only) Makes dark subjects or areas even brighter than they would be under good natural lighting. 1) Set the Power Switch @ to “ ” or “ ” while pressing down the Lock Button ! located on the switch.
24 Programme AE With Special Ef fects 1) Set the Power Switch @ to “ ” while pressing down the Lock Button ! located on the switch. 2) Press P .AE ^ repeatedly until the desired mode appears. • T o cancel the effect, press P .AE ^ repeatedly until “ OFF ” appears.
25 TROUBLESHOOTING Before consulting your JVC dealer , please check the following to see if you can correct the problem yourself. Vertical white lines appear when shooting a very bright object. • This sometimes occurs when the contrast between the back-ground and the object is great.
26 2. T o prevent damage and prolong service life . . . .... do not subject to unnecessary shock. .... avoid repeated charging without fully discharging. .... charge in an environment where temperatures are within the tolerances shown in the chart below .
27 For Y our Maintenance 1. After Use 1 Set the Power Switch to “ OFF ” to turn off the camcorder . 2 Open the LCD monitor* to an angle of over 60 degrees. Slide EJECT to open the cassette holder , then remove the cassette. 3 Close and lock the cassette holder by pressing the Close button.
28 SPECIFICA TIONS Camcorder General Format : S-VHS (GR-SXM49/SX25 only)/ VHS P AL standard Power source : DC 1 1 V (Using AC Adapter) DC 6 V (Using battery pack) Power consumption Viewfinder on : 4.2 W (GR-SXM49/FXM393/ FXM39 only) 4.0 W (GR-SX25/FX15 only) LCD monitor * on : 4.
デバイスJVC GR-FXM39の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC GR-FXM39をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC GR-FXM39の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC GR-FXM39の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC GR-FXM39で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC GR-FXM39を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC GR-FXM39の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC GR-FXM39に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC GR-FXM39デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
