AMXメーカーMXD-1000-NCの使用説明書/サービス説明書
ページ先へ移動 of 42
Operation/Reference Guide Touch Panels MXT/D-1000 10.1" ModeroX Series® Tabletop Touch Panel 10.1" Modero X Series® Wa ll/Flush Mount Touch Panel Last Updated: 10/24/201 2.
AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity .
AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software.
.
Table of Contents i MXD/T-1000 10.1" Modero® X Series Touch Panels Table of Contents Modero X Series® Touch Panels ........................................................................ 1 Overview .............................. ..............
ii MXD/T-1000 10.1" Modero® X Series Touch Panels Table of Contents Upgrading Firmware ........................... ............................................... ............... 25 Overview ........... .................... .....................
Modero X Series® Touch Panels 1 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Modero X Series® Touch Panels Overview See more and do more with the most ele gant interf ace designed sp ecific ally for dedicated room control.
Modero X Series® Touch Panels 2 MXD/T-1000 10.1" Modero X Series® Touch Panels MXT-1000 The MXT -1000 ( FG5968-03 ) (FIG. 1) is ideal for boardrooms, conf erence rooms, or auditoriums where a panoramic contro l surface is needed to pro vide access to multiple funct ions simultaneously while remaining elegantly unobtrusi ve.
Modero X Series® Touch Panels 3 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels MXT-1000 Specifications Power Requirements: PoE (Power over Ethernet), 802.
Modero X Series® Touch Panels 4 MXD/T-1000 10.1" Modero X Series® Touch Panels Connector Locations W ith the unit facing you, the tw o USB ports for peripherals are located on the rear right corner of the device (FIG. 3). The RJ45 connector for PoE, as well as a 5-pin Micro-USB port, is also located on the back of the de vice.
Modero X Series® Touch Panels 5 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Memory The MXT -1000 comes with 512 MB of SDRAM and 4 GB of Flash memory , neither of which can be upgraded. A maximum of 2.4 GB is a vailable to the u ser for projects.
Modero X Series® Touch Panels 6 MXD/T-1000 10.1" Modero X Series® Touch Panels MXD-1000 The MXD-1000 10.1” Modero X Series Panoramic W all T ouch Panels ( P ortrait W all Mount: FG5968-07 ; L.
Modero X Series® Touch Panels 7 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels MXD-1000 Specifications Power Requirements: PoE (Power over Ethernet), 802.
Modero X Series® Touch Panels 8 MXD/T-1000 10.1" Modero X Series® Touch Panels MXD-1000 Specific ations (Cont.) Communications (Cont.): Bluetooth: HID Profile v1.
Modero X Series® Touch Panels 9 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Memory The MXD-1000 comes with 512 MB of SDRAM and 4 GB of Flash memory , neither of which can be upgraded. A maximum of 2.4 GB is a vailable to the u ser for projects.
Modero X Series® Touch Panels 10 MXD/T-1000 10.1" Modero X Series® Touch Panels MXD/T-1000 Features Picture View By connecting a USB driv e via one of the de vice’ s USB ports (FIG. 3), Picture V iew allo ws the MXT -1000 to access JPEG images on that dri ve an d display them on the touchscreen (FIG.
Modero X Series® Touch Panels 11 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels 3. On the leftmost amber button, select between Rand (images display at random) and A-Z (images display in alphabetical order based on the name of the file ).
Modero X Series® Touch Panels 12 MXD/T-1000 10.1" Modero X Series® Touch Panels Picture View Send Co mmand The ^PIC Send Command stops either mode of Picture V iew , or starts Pre vie w Mode. For more information, please refer to the Moder o X Series Pro gramming Guide , available at www .
Installation 13 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Installation MXT-1000 Installation Any USB peripherals (mouse, ke yboard, et c.) may be connected to one of th e two USB ports on the rear of the dev ice (FIG. 9). Updates to the de vice’ s firmwa re are also made via the USB ports.
Installation 14 MXD/T-1000 10.1" Modero X Series® Touch Panels T o disconnect and reconnect the MXT -1000’ s Ethernet cable to allo w use of a hole smaller than 1.00” in diameter: 1. On a soft surface, turn the MXT - 1000 face-do wn to access the bottom of the device.
Installation 15 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Installing the MX D-1000 into a wall The MXD-1000 comes with a clear plastic backbox ( desi gned to attach the panel to most standard wall materials. This backbox has four locking tabs (two on top an d two on bottom) to help lock the backbox to the wall.
Installation 16 MXD/T-1000 10.1" Modero X Series® Touch Panels T o install the back box: 1. Prepare the area by removing any scre ws or nails fro m the drywall before begi nning the cutout process. 2. For best resu lts, use the MXD-1000 Installation T emplate ( 68-5968-03 ) to ensure proper placement (FIG.
Installation 17 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels 4. Thread the incoming Et hernet and Micro-USB wiri ng (if Micro-USB access is desired) from their terminal locations through the surface opening (FIG. 16 ). Leave enough slack in the wiring to accommodate any r e-pos itioning of the panel.
Installation 18 MXD/T-1000 10.1" Modero X Series® Touch Panels 11 . T est the incoming wiring by attaching the panel conne ctions to their terminal locations and applying power . V erify that the panel is rece iv ing po wer a nd functioning properly to pre vent r epetition of the installation.
Installation 19 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels 13. Reconnect the terminal Ethe rnet and USB to their respecti ve loca tions on either the Ethernet port or NetLinx Master . Uninstalling the MXD-1000 The MXD-1000 is held in place to the back box via latch hooks and clips on the back box (FIG.
Installation 20 MXD/T-1000 10.1" Modero X Series® Touch Panels 2. W ith a stout, strong point (a push pi n or straightened paperclip, for e xample), carefully press into the access holes in either end of the molding (FI G. 21) until the snap is disconne cted.
Installation 21 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels.
Installation 22 MXD/T-1000 10.1" Modero X Series® Touch Panels.
Configuration and Programming 23 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Configuration and Programming Modero X Series Programming Guide Information on Settings pages, panel configur ation, a nd programming is included in the Moder o X Series Pr ogramming Guide , av ailable at www .
Configuration and Programming 24 MXD/T-1000 10.1" Modero X Series® Touch Panels.
Upgrading Firmware 25 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Upgrading Firmware Overview The latest f irmware (*.kit) f ile for eac h panel is a v ailable to do wnload from www .
Upgrading Firmware 26 MXD/T-1000 10.1" Modero X Series® Touch Panels 4. Eject or unmount the flash dri ve from the PC. Transfer the Fi rmware File From th e Flash Drive to the Tou ch Panel 1. Connect the USB Flash Driv e to one of the USB T ype A ports on th e panel.
Upgrading Firmware 27 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Upgrading from Previous Firmware The MXT -1000 and MXD-1000 allow the optio n to rev ert the de vice to the pre vious f irmware run before an upgrade. T o upgrade the device from pre viously loaded firmw a re: 1.
Upgrading Firmware 28 MXD/T-1000 10.1" Modero X Series® Touch Panels Upgrading Firmware Via NetLinx Studio The MXT -1000 and MXD-1000 use an Ethe rnet connection for programming, firmw are updates, and touch panel file transfer via NetLinx Stu dio.
Upgrading Firmware 29 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels 5. Click the Edit Settings b utton on the Communications Settings dialog to open the V irtual NetLinx Master Settings dialog (FIG. 28). 6. W ithin this dialog, enter the Master System number .
Upgrading Firmware 30 MXD/T-1000 10.1" Modero X Series® Touch Panels Viewing devices on the Virtual System 1. After the Communication V erification dialog windo w ve rifies acti ve communication between the V irtual Master and the panel, click the OnLine T ree tab in the W orkspace windo w (FIG.
Upgrading Firmware 31 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels 4. Select the appropri ate Kit f ile from withi n the Br owse for F older window (FIG.
Upgrading Firmware 32 MXD/T-1000 10.1" Modero X Series® Touch Panels.
Appendix: Troubleshooting 33 MXD/T-1000 10.1" Modero X Ser ies® Touch Panels Appendix: Troubleshooting Overview This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero X touch panel.
Appendix: Troubleshooting 34 MXD/T-1000 10.1" Modero X Series® Touch Panels.
Appendix - Troubleshooting 35 MXD/T-1000 10.1" Modero X Series ® Touch Panels.
10/2012 © 2012 AMX. All rights reserved. AMX and the AMX logo are register ed trademarks of AMX. AMX rese rves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.
デバイスAMX MXD-1000-NCの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
AMX MXD-1000-NCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAMX MXD-1000-NCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AMX MXD-1000-NCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AMX MXD-1000-NCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AMX MXD-1000-NCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAMX MXD-1000-NCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AMX MXD-1000-NCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAMX MXD-1000-NCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
