JVCメーカーRX-558VBKの使用説明書/サービス説明書
ページ先へ移動 of 30
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
G-1 W arnings, Cautions and Others Caution –– POWER switch! Disconnect the mains plug to shut the power off completely. The POWER switch in any position does not disconnect the mains line. The power can be remote controlled. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
1 English T able of Contents Parts Identification ...................................... 2 Getting Star ted ........................................... 3 Before Installation ...................................................................... 3 Checking the Supplied Accessories .
2 English Par ts Identification Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details.
3 English Getting Star ted This section explains how to connect audio/video components and speakers to the receiver , and how to connect the power supply . Before Installation General • Be sure your hands are dry . • T urn the power of f to all components.
4 English RIGHT LEFT REAR SPEAKERS CENTER SPEAKER T urn the loop until you ha ve the best reception. Note: • Make sure the antenna conductors do not touch any other ter minals, connecting cords and power cord. This could cause poor reception. • If reception is poor , connect an outdoor single vinyl-cov ered wire to the AM EXT ter minal.
5 English AUDIO PHONO T APE/MD CD OUT (REC) IN (PLA Y) L R ANTENNA AM EXT AM LOOP FM 75 COAXIAL Connecting the subwoofer speaker Y ou can enhance the bass by connecting a subwoofer . Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs.
6 English VIDEO AUDIO LEFT RIGHT MONI T OR OUT OUT (REC) IN (PL A Y) OUT (REC) IN (PL A Y) DVD VCR VHS V ideo component connections Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack and the yellow plug to the video jack.
7 English Putting Batteries in the Remote Control Before using the remote control, put two supplied batteries fir st. When using the remote control, aim the remote control directly at the remote sensor on the receiv er . 1. On the back of the remote control, r emove the battery cover as illustr ated.
8 T urning the Power On and Off (Standby) On the front panel: T o turn on the power , press PO WER. The ST ANDBY lamp goes off. The name of the current source (or station frequency) appears on the display . T o turn off the power (into standby mode), press POWER again.
9 Adjusting the V olume On the front panel: T o increase the volume, turn MASTER VOLUME clockwise (+). T o decrease the volume, turn it counterclockwise (–). • When you turn MASTER V OLUME rapidly , the volume le vel also changes rapidly . • When you turn MASTER V OLUME slowly , the v olume level also changes slo wly .
10 Attenuating the Input Signal When the input le vel of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion. On the front panel ONL Y : Press INPUT A TT .
11 Changing the Source Name When you hav e connected an MD recorder to the T APE/MD jacks on the rear panel: Change the source name shown on the display when you select the MD recorder as the source. On the front panel ONL Y : When changing the source name from “T APE” to “MD”: 1.
12 T o store the sound settings 1. Press ONE T OUCH OPERA TION. The ONE T OUCH OPERA TION lamp lights up, then the previously memorized settings are recalled. 2. Adjust the sound using the functions listed to the left. The newly adjusted settings are memorized.
13 Using Preset T uning Once a station is assigned to a channel number , the station can be quickly tuned. Y ou can preset up to 30 FM stations and 15 AM stations. T o store the pr eset stations Bef ore you start, r emember ... • There is a time limit in doing the following steps.
14 Selecting the FM Reception Mode When an FM stereo br oadcast is har d to receive or noisy Y ou can change the FM reception mode while recei ving an FM broadcast. On the front panel ONL Y : 1. Press FM. The last station of the selected band is tuned in.
15 Using the DSP Modes The built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D-PHONIC mode, DAP (Digital Acoustic Processor) mode and Surround mode (Dolby Pro Logic and JVC Theater Surround). * Manufactured under license from Dolby Laboratories Licensing Corporation.
16 Available DSP Modes According to the Speaker Ar rangement A v ailable DSP modes will vary depending on ho w many speakers are used with this recei ver .
17 Adjusting the DAP Modes Bef ore you start, r emember ... • Make sur e tha t you ha ve set the speaker inf ormation correctly (see page 11). • There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
18 From the r emote contr ol: 1. Press SOUND CONTR OL. The 10 keys are activated for sound adjustments. 2. Press SURR OUND r epeatedly until the D AP mode — D ANCE CLUB, LIVE CLUB, HALL, or P A VILION — a ppear s on the display . The D AP indicator also lights up on the display .
19 8. ONL Y FOR JVC Theater Surround: Press cursor contr ol @ / # to select an effect lev el you want. • Each time you press the button, the ef fect level changes as follows: As the number increases, JVC Thea ter Surround becomes stronger .
20 Using the DVD MUL TI Playback Mode This receiver provides the DVD MUL TI playback mode for r epr oducing the analog discrete output mode of the DVD player . Before playing back a DVD, refer also to the manual supplied with the DVD player . 7. Press cursor contr ol @ / # to adjust the left rear speak er output level (fr om –10 to +10).
21 COMPU LINK Remote Contr ol System The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver .
22 Operating JVC’ s Audio/V ideo Components Y ou can operate JVC’s audio and video components with this receiver’ s remote control, since control signals for JVC components are preset in the remote control.
23 After pressing D VD or D VD MUL TI, these b uttons can be used for the DVD menu operations. Note: For detailed men u operations, ref er to the instructions supplied with the discs or the D VD pla yer . TV Y ou can always perfor m the following operations: TV POWER : T urns on or of f the TV .
24 PROBLEM The display does not light up. No sound from speakers. Sound from one speaker only. Continuous hiss or buzzing during FM reception. Occasional cracking noise during FM reception. Howling during record playing. “OVERLOAD” starts flashing on the display.
25 Specifications Amplifier Output Power At Stereo operation: 100 watts per channel, min. RMS, driven into 8 ohms, at 40 Hz to 20 kHz with no more than 0.8 % total harmonic distortion. At Surround operation: Front Channel: 100 watts per channel, min. RMS, driven into 8 ohms at 1 kHz with no more than 0.
G-2 Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous.
G-3 LIMITED W ARRANTY AUDIO-2 JVC COMP ANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONL Y T O THE ORIGINAL PURCHASER A T RET AIL to be FREE FROM DEFECTIVE MA TERIAL AND WORKMANSHIP from the date of original retail purchase for the period as shown below .
VICTOR COMP ANY OF JAP AN , L IMITED EN J V C 1298HIMMDWJEM RX-558V[J]COVER/1 98.12.15, 3:55 PM 2.
デバイスJVC RX-558VBKの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
JVC RX-558VBKをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはJVC RX-558VBKの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。JVC RX-558VBKの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。JVC RX-558VBKで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
JVC RX-558VBKを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はJVC RX-558VBKの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、JVC RX-558VBKに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちJVC RX-558VBKデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
