Analog DevicesメーカーADSP-BF538Fの使用説明書/サービス説明書
ページ先へ移動 of 101
ADSP-BF538F EZ-KIT Lite ® Evaluation System Manual Revision 1. 2 , April 2008 Part Number 82-000945-01 Analog Devices, Inc. One T echnology W ay N o rwood, Mass.
Copyright Information ©2008 Analog Devices, Inc., ALL RIGH TS RESERVED. This document may not be reproduced in any form wi thout prior, express written consent from Analog Devices, Inc.
Regulatory Compliance The ADSP-BF538F EZ-KIT Lite is designed to be used solely in a labora- tory environment. The board is not intended for use as a consumer end product or as a portion of a consume r end product.
.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual v CONTENTS PRE F A C E P urpose of This Manual ................................................................ xiii Intended A udience ..................................................................
CONTENTS vi ADSP-BF538F EZ-KIT Lite Evaluation System Manual E valuation License Re strictions ..................................................... 1-7 M emor y Map ............................................................................... 1-7 SDRAM Interfac e .
ADSP-BF538F EZ-KIT Lite Evaluation System Manual vii CONTENTS Flash Enable S witch (SW6) .................................................... 2-11 FCE Enable S witch (SW14) ................................................... 2-12 Audio Enable S witch (SW7) .
CONTENTS viii ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPOR T0 and SPOR T1 Connectors (P6 and P7) .................... 2-23 PPI Connector (P8) .............................................................. 2-23 SPI Connector (P9) .............
ADSP-BF538F EZ-KIT Lite Evaluation System Manual ix PREFACE Thank you for purchasing the ADSP-BF538F EZ-KIT Lite ® , Analog Devices, Inc. evaluation system for Blackfin ® processors.
x ADSP-BF538F EZ-KIT Lite Evaluation System Manual The evaluation board is de signed to be used in co njunction with the Visu- alDSP++ ® development environment to te st the capabilities of the ADSP-BF538F Blackfin processors.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual xi Preface The board features: • Analog Devices ADSP -BF538F processor D Core performance up to 600 MHz D External bus performance to 133 MHz D 182-p.
xii ADSP-BF538F EZ-KIT Lite Evaluation System Manual • Universal asynchronous re ceiver/transm itter (UART) D ADM3202 RS-232 line driver/receiver D DB9 female connector •L E D s D 10 LEDs: 1 power.
ADSP-BF538F EZ-KIT Lite Eval uation System Manual xiii Preface Additionally, the EZ-KIT Li te board provides access to all of the proces- sor’s peripheral ports. Access is provided in the form of a three-connector expansion interface. For more information, see “Expansion Interface” on page 2-8 .
Manual Contents xiv ADSP-BF538F EZ-KIT Lite Evaluation System Manual Manual Contents The manual consists of: • Chapter 1, “Using ADSP-BF538F EZ-KIT Lite” on page 1-1 . Describes EZ-KIT Lite functional ity from a programmer’s perspec- tive and provides an ea sy-to-access memory map.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual xv Preface Technical or Customer Support You can reach Analog Devices, Inc. Customer Support in the following ways: • Visit the Embedded Processing and DSP products Web site at http://www.analog.com/processors/tec hnicalSupport • E-mail tools questions to processor.
Product Information xvi ADSP-BF538F EZ-KIT Lite Evaluation System Manual Product Information You can obtain product information from the Analog Devices Web site, from the product CD-ROM, or from printed publications (manuals). Analog Devices is online at www.
ADSP-BF538F EZ-KIT Lite Eval uation System Manual xvii Preface You may also obtain additional info rmation about Analog Devices and its products in any of the following ways. • E-mail questions or requests for information to processor.support@analog.
Product Information xviii ADSP-BF538F EZ-KIT Lite Evaluation System Manual Online Technical Documentation Online documentation comprises the VisualDSP++ Help system, software tools manuals, hardware t.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual xix Preface Accessing Documentation From VisualDSP++ To view VisualDSP++ Help, click on the Help menu item or go to the Windows task bar and navigate to the VisualDSP++ documentation via the Start menu.
Product Information xx ADSP-BF538F EZ-KIT Lite Evaluation System Manual Accessing Documenta tion From Web Download manuals at the following Web site: http://www.analog.com/processors/te chnicalSupport/technicalLi- brary/ . Select a processor family and b ook title.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual xxi Preface Notation Conventions Text conventions used in this manual are identified and described as fol- lows. Additional conventions, which appl y only to specific chapters, may appear throughout this document.
Notation Conventions xxii ADSP-BF538F EZ-KIT Lite Evaluation System Manual.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-1 1 USING ADSP-BF538F EZ-KIT LITE This chapter provides specific informati on to assist you with development of programs for the ADSP-BF538F EZ -KIT Lite evalua tion system. The information appears in the following sections.
1-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual • “CAN Interface” on page 1-11 Describes the on-board Controller Area Network (CAN) interface. • “ELVIS Interface” on page 1-12 Describes the on-board National Instruments Educational Labora- tory Virtual Instrumentation Suite (NI ELVIS) interface.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-3 Using ADSP-BF538F EZ-KIT Lite Package Contents Your ADSP-BF538F EZ-KIT Lite evaluation system package contains the following items.
Default Configuration 1-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual When removing the EZ-KIT Lite board from the package, handle the board carefully to avoid the discharg e of static electri city, which may dam- age some components. Figure 1-1 shows the default jumper settings, switches, connector locations, and LE Ds used in installation.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-5 Using ADSP-BF538F EZ-KIT Lite Installation and Session Startup L For correct operation, install the software and hardware in the order presented in the VisualDSP++ Install ation Quick Reference Card .
Installation and Session Startup 1-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 5. The Select Connection Type page of the wizard appears on the screen. Select EZ-KIT Lite and click Next . 6. The Select Platform page of the wizard appears on the screen.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-7 Using ADSP-BF538F EZ-KIT Lite Evaluation License Restrictions The ADSP-BF538F EZ-KIT Lite installation is part of the VisualDSP++ installation. The EZ-KIT Lite is a lice nsed product that offers an unre- stricted evaluation license for th e first 90 days.
SDRAM Interface 1-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SDRAM Interface The three SDRAM control registers must be initialized in order to use the MT48LC32M8A2 32M x 16 bits (64 MB) SDRAM memory. When you are in a VisualDSP++ session and conne ct to the EZ-KIT Lite board, the T able 1-1.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-9 Using ADSP-BF538F EZ-KIT Lite SDRAM registers are configured automatically through the debugger each time the processor is reset. The values in Table 1-2 are used whenever SDRAM bank 0 is accessed throug h the debugger (for example, when viewing memory windows or load ing a program).
Flash Memory 1-10 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Automatic configuration of SD RAM is not optimized for any SCLK fre- quency. Table 1-3 shows optimized configuration for the SDRAM registers using a 125 MHz and 133 MHz SCLK . Only the EBIU_SDRRC reg- ister needs to be modified in th e user code to achieve maximum performance.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-11 Using ADSP-BF538F EZ-KIT Lite Example code is provided in the EZ-K IT Lite installation directory to demonstrate how to program flash memory. Table 1-4 shows a sample value for the asynchronous memory configura- tion register, EBIU_AMBCTL0 .
ELVIS Interface 1-12 ADSP-BF538F EZ-KIT Lite Evaluation System Manual ELVIS Interface This EZ-KIT Lite board contains the National Instruments ELVIS inter- face. The interface features the DC voltage and current measurement modules, oscilloscope and bode an alyzer modu les, function generator, arbitrary waveform gener ator, and digital IO.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 1-13 Using ADSP-BF538F EZ-KIT Lite The frame sync and bit clocks are gener ated from the ADC and feed to the processor because the ADC is operating in master mode. The audio inter- face samples data at a 48 kHz sample rate.
Example Programs 1-14 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Example Programs Example programs are provided with the ADSP-BF538F EZ-KIT Lite to demonstrate various capabilities of the evaluation board.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-1 2 ADSP-BF538F EZ-KIT LITE HARDWARE REFERENCE This chapter describes the hardware design of the ADSP-BF538F EZ-KIT Lite board.
System Architecture 2-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual System Architecture This section describes the processor’ s configuration on the EZ-KIT Lite board. This EZ-KIT Lite is designed to demonstrate capabilities of the ADSP-BF538F Blackfin processor.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-3 ADSP-BF538F EZ-KIT Lite Hardware Reference The core voltage and the core clock rate can be set on the fly by the pro- cessor. The input clock is 25 MHz. A 32.768 kHz crystal supplies the real-time clock (RTC) inputs of the pr ocessor.
System Architecture 2-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPORT0 Interface SPORT0 connects to the audio circuit, SPORT0 connector ( P6 ), and expan- sion interface. The audio circuit uses the primary data transmit and receive pins to input and output da ta from the audio input and outputs.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-5 ADSP-BF538F EZ-KIT Lite Hardware Reference PC5 LED ( LED2 ) or ELVIS_PF1 . See “LED and Push Button Locations” on page 2-17 and “Push Button Enable Switch (SW5)” on page 2-11 for information on how to disable the push button.
System Architecture 2-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual PD7 SCK2 PPI_DIR _CTL (for A V -Extender ® ) PD8 SPI2SS PPI_CLK_SE L (for A V -Extender) PD9 SPI2SEL CAN_ERR PD10 RX1 No t u s.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-7 ADSP-BF538F EZ-KIT Lite Hardware Reference PF0 SPISS Push button ( SW 13 ). See “Programmable Flag Push Buttons (SW10–13)” on page 2-18 . PF1 SPI0SEL1/TMR CLK P ush button ( SW12 ). See “Programmable Flag Push Buttons (SW10–13)” on page 2-18 .
System Architecture 2-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual UART Port The universal asynchronous receiver/t ransmitter (UART) port of the pro- cessor connects to the ADM3202 RS-232 line driver as well as to the expansion interface.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-9 ADSP-BF538F EZ-KIT Lite Hardware Reference JTAG Emulation Port The JTAG emulation port allows an emulator to access the processor’s internal and external memory through a 6-pin interface. The JTAG emu- lation port of the proces sor connects also to the USB debugging interface.
Jumper and Switch Settings 2-10 ADSP-BF538F EZ-KIT Lite Evaluation System Manual CAN Enable Switch (SW2) The Controller Area Network (CAN) enable switch ( SW2 ) disconnects CAN signals from the GPIO pins of the processor. When the SW2 switch is in the OFF position, the associated GPIO signals (see Table 2-3 ) can be used on the expansion interface.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-11 ADSP-BF538F EZ-KIT Lite Hardware Reference Push Button Enable Switch (SW5) The push button enable switch ( SW5 ) disconnects the associated signal and the push button circuit drivers from the GPIO pins of the processor.
Jumper and Switch Settings 2-12 ADSP-BF538F EZ-KIT Lite Evaluation System Manual FCE Enable Switch (SW14) The flash chip enable (FCE) switch ( SW14 ) selects which ~AMS signals con- nect to the internal flash memory. Since the internal memory is 1 MB, only one ~AMS signal must be connected at a time.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-13 ADSP-BF538F EZ-KIT Lite Hardware Reference Boot Mode Select Switch (SW3) The rotary switch ( SW3 ) determines the boot mo de of the processor. Table 2-9 shows the available boot mo de settings. By default, the ADSP-BF538F processor boots from the on-board flash memory.
Jumper and Switch Settings 2-14 ADSP-BF538F EZ-KIT Lite Evaluation System Manual UART Loop Jumper (JP9) The UART loop jumper ( JP9 ) is for looping the transmit and receive sig- nals.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-15 ADSP-BF538F EZ-KIT Lite Hardware Reference ELVIS Function Generator Configuration Switch (SW8) The function generator configuration switch ( SW8 ) controls signals con- necting to the left and right input signals of the audio interface.
Jumper and Switch Settings 2-16 ADSP-BF538F EZ-KIT Lite Evaluation System Manual ELVIS Voltage Selection Jumper (JP6) The ELVIS voltage selection jumper ( JP6 ) is used to select the power source for the EZ-KIT Lite. In a standard mode of operation, the board receives its power from an external powe r supply.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-17 ADSP-BF538F EZ-KIT Lite Hardware Reference LEDs and Push Buttons This section describes functionality of the LEDs and push buttons. Figure 2-3 shows the locations of the LEDs and push buttons. Reset Push Button (SW9) The RESET push button resets all of the IC s on the board.
LEDs and Push Buttons 2-18 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Programmable Flag Push Buttons (SW10–13) Four push buttons, SW10–13 , are provided for general -purpose user input. The buttons connect to the PF0-3 programmable flag pins of the proces- sor.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-19 ADSP-BF538F EZ-KIT Lite Hardware Reference User LEDs (LED2–6) Five LEDs connect to five general-pur pose IO pins of the processor (see Table 2-15 ). The LEDs are active high and are lit by writing a 1 to the correct PC signal.
Connectors 2-20 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Connectors This section describes the connector functionality and provides informa- tion about mating connectors.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-21 ADSP-BF538F EZ-KIT Lite Hardware Reference Audio Connectors (J9 and J10) CAN Connectors (J5 and J11) RS-232 Connector (J6) P ar t Description Manufactur er P art Number 3.5 mm stereo jack A/D ELECTR ONICS ST323-5 Mating Cable (shipped with EZ-KIT Lite) 3.
Connectors 2-22 ADSP-BF538F EZ-KIT Lite Evaluation System Manual Power Connector (J7) The power connector provides all of the power necessary to operate the EZ-KIT Lite board. Expansion Interface Connectors (J1–3) Three board-to-board connector footprints provide signals for most of the processor’s peripheral interfaces.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-23 ADSP-BF538F EZ-KIT Lite Hardware Reference JTAG Connector (ZP4) The JTAG header is the connecting point for a JTAG in-circuit emulator pod. When an emulator connects to the JTAG header, the USB debug interface is disabled.
Connectors 2-24 ADSP-BF538F EZ-KIT Lite Evaluation System Manual SPI Connector (P9) The pinout of the P9 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 . 2-Wire Interface Connector (P10) The pinout of the P10 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 .
ADSP-BF538F EZ-KIT Lite Evaluation System Manual 2-25 ADSP-BF538F EZ-KIT Lite Hardware Reference UART1 Connector (P12) The pinout of the P12 connector can be found in “ADSP-BF538F EZ-KIT Lite Schematic” on page B-1 .
Connectors 2-26 ADSP-BF538F EZ-KIT Lite Evaluation System Manual.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-1 A ADSP-BF538F EZ-KIT LITE BILL OF MATERIALS The bill of materials corresponds to “ADSP-BF538F EZ-KIT Lite Sche- matic” on page B-1 .
A-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 13 2 FDS6990AS SOIC8 U12-13 F AIRCHILD FDS6990AS 14 1 BF538 M29W320 E B “U24” U24 ST MICR O M29W320EB70ZE6E 15 1 ADM708SARZ SOIC8 U27 ANALOG DE.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-3 ADSP-BF538F EZ-KIT Lite Bill Of Materials 30 5 DIP4 SWT018 SW2,SW4-6, SW14 ITT TDA 04HOSB1 31 1 DB9 9PIN CON038 J6 NOR COMP 191-009-213-L-571 32 2 .
A-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 48 1 10UF 16V 10% C CT7 A VX T AJC106K016R 49 6 10K 1/10W 5% 0805 R69-74 VISHA Y CRCW080510K0JNEA 50 4 100 1/10W 5% 0805 R82,R100-101, R103 VISHA Y.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-5 ADSP-BF538F EZ-KIT Lite Bill Of Materials 61 71 0.01UF 16V 10% 0402 C1-27,C30-46, C91-93,C95-97, C103-104, C107-109,C132, C137,C141, C143-147, C202.
A-6 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 73 4 0.01UF 16V 10% 0603 C50-51,C62-63 A VX 0603YC103KA T2A 74 1 4.7UF 25V 20% 0805 C110 A VX 0805ZD475KA T2A 75 2 330PF 50V 5% 0603 C79,C84 A VX 0.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual A-7 ADSP-BF538F EZ-KIT Lite Bill Of Materials 88 4 5.49K 1/10W 1% 0603 R42-43,R46-47 DIGI-KE Y 311-5.49KHR TR-ND 89 2 3.32K 1/10W 1% 0603 R44,R48 DIGI-KEY 31 1-3.32KHR TR-ND 90 2 1.65K 1/10W 1% 0603 R45,R49 DIGI-KEY 31 1-1.
A-8 ADSP-BF538F EZ-KIT Lite Evaluation System Manual 103 2 2200PF 50V 5% 0603 C76,C78 PANASONIC ECJ-1VB1H222K 104 2 2.74K 1/10W 1% 0603 R36,R52 DIGI-KEY 311-2.
D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.
3.3V NC1 NC2 TERM1 TERM2 SWE SRAS SMS SCAS RESET NMI FRESET FCE BR BGH BG AWE ARE AOE AMS3 AMS2 AMS1 AMS0 XTAL SCKE SA10 RTXO RTXI D8 D7 D6 D5 D4 D3 D2 D15 D14 D13 D12 D11 D10 D1 D0 CLKOUT CLKIN BMODE.
GPW VROUT1 VROUT0 VDDRTC VDDINT9 VDDINT8 VDDINT7 VDDINT6 VDDINT5 VDDINT4 VDDINT3 VDDINT2 VDDINT12 VDDINT11 VDDINT10 VDDINT1 VDDEXT9 VDDEXT8 VDDEXT7 VDDEXT6 VDDEXT5 VDDEXT4 VDDEXT3 VDDEXT21 VDDEXT20 VD.
3.3V 3.3V 3.3V 3.3V 3.3V 3.3V A0 A1 A10 A11 A12 A2 A3 A4 A5 A6 A7 A8 A9 BA0 BA1 CKE CLK DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQM GND1 GND2 GND3 GND4 GND5 VDD1 VDD2 VDD3 VDD4 VDD5 VDD6 CAS CS RAS WE VDD7 GN.
AGND AGND 3.3V 5V A5V 5V A5V AGND AGND AGND AGND AGND AGND AGND AGND AGND 3.3V BCLK CAPLN CAPLP CAPRN CAPRP CASC CIN/{DF1} CLATCH/{M~/S} COUT/{DF0} DIN DOUT LRCLK MCLK VINLN VINLP VINRN VINRP VREF XCTRL RESET CCLK/{256~/512} 8 12 4567 ON 3 3.3V AGND 3.
5V A5V AGND 3.3V 3.3V AGND AGND AGND 384/256~ 96/48~ BCLK CCLK CDATA CLATCH DEEMP FILTB FILTR IDPM0 IDPM1 LRCLK MCLK MUTE OUTL+ OUTL- OUTR+ OUTR- SDATA X2MCLK ZEROL ZEROR RESET OE OUT 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No.
5V 3.3V 3.3V 3.3V CANH CANL EN ERR GND INH RXD SPLIT STB TXD VBAT VDD VIO WAKE 5V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.
3.3V 3.3V 3.3V 3.3V 3.3V 3.3V I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E 1A1 1A2 1A3 1A4 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2A1 2Y4 2Y3 OE1 OE2 I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC YD E PFI RESET MR PFO RESET 3.3V ON 1 2 3 4 1 2 ON D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No.
A5V A5V JUMPER SHORTING JUMPER SHORTING 3.3V AGND AGND AGND A5V A5V AGND AGND 8 1 2 4 5 6 7 ON 3 IN+ IN- OUT REF RG+ RG- V+ V- IN+ IN- OUT REF RG+ RG- V+ V- I0A I0B I0C I0D I1A I1B I1C I1D S YA YB YC .
3.3V SHGND 3V DA_EMULATOR_TCK DA_EMULATOR_TDI DA_EMULATOR_TDO DA_EMULATOR_TMS DA_GP0 DA_GP1 DA_GP2 DA_GP3 GND SHGND TCK TDI TDO TMS DA_EMULATOR_EMU DA_EMULATOR_SELECT DA_EMULATOR_TRST DA_SOFT_RESET EMU RESET TRST DEBUG_AGENT 5V 5V 3.3V 3.3V 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No.
3.3V 3.3V 5V 3.3V 3.3V 5V 3.3V 3.3V 5V 5V 5V 5V 3.3V 5V C1+ C1- C2+ C2- R1IN R1OUT R2IN R2OUT T1OUT T2IN T2OUT V- V+ T1IN ON 1 2 3 4 JUMPER SHORTING 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No.
D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.
3.3V 3.3V MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT MSC009 RUBBER FOOT 3.3V D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev ADSP-BF538F EZ-KIT LITE A0203-2006 1.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-1 INDEX Numerics 2-wire interface (TWI), 1-13 , 2-24 A AD1854 digital-to-analog converter (DAC), 1-12 AD1871 analog-to-digital conver ter (ADC), 1-12.
INDEX I-2 ADSP-BF538F EZ-KIT Lite Evaluation System Manual connectors diagram of locations, 2-20 J1-3 (expansion), 2-3 , 2- 8 , 2- 22 J5 and J11 (CAN), 2-21 J6 (RS-232 ), 2-21 J7 (power), 2-22 J9-10 (.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-3 INDEX H Help, online, xix I installation, of this EZ-KIT Lite, 1-5 interfaces, See audio, CAN, ELVIS, expansion, SDRAM internal memory core/system .
INDEX I-4 ADSP-BF538F EZ-KIT Lite Evaluation System Manual PPI_DIR_CTL signal, 2-6 PPI_FS3 signal, 2-7 programmable flags PC0 (UART transmit), 1- 11 , 2-4 , 2-10 PC1 (UART receive), 1-1 1 , 2-4 , 2- 1.
ADSP-BF538F EZ-KIT Lite Evaluation System Manual I-5 INDEX SW6 (flash enable) switch, 1-10 , 2-11 SW7 (audio enable) switch, 1-13 , 2-12 SW8 (audio input) switch, 2-1 5 SW9 (reset) push button, 2-17 s.
.
Analog Devices : Embedded Processing & DSP Home View Cart | My Account | Log In Home Contact Us | Print this Page | Email this Page Blackfin is picture perfect: Leica SLR Camera Processors Explore, Evaluate, Design Everything you need, from Software Development Tools, Third Party Support, Technical Library and more.
Analog Devices : Embedded Processing & DSP Home ● Third Party Collaborative Learning and Development ● Blackfin Online Learning and Development (BOLD), Workshops and Seminars, University Progr.
Analog Devices : Embedded Processing & DSP : Technical Support : Technical Support Home View Cart | My Account | Log In Home > Embedded Processing & DSP Contact Us | Print this Page | Email.
Analog Devices : Embedded Processing & DSP : Technical Support : Technical Support Home Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc. All Rights Reserved. This site is optimized for IE 6.
Log In Parametric Search | Replacement Parts Search View Cart | My Account | Log In Home Contact ADI Log In: Enter Email Address: Do you have a password? No, I am a new user. Yes, I have a password: Forgot your password? Keep me logged in unless I log out.
Analog Devices : Embedded Processing & DSP Home View Cart | My Account | Log In Home Contact Us | Print this Page | Email this Page SHARC Processor: Leadership in MFLOPS per $ Performance Processors Explore, Evaluate, Design Everything you need, from Software Development Tools, Third Party Support, Technical Library and more.
Analog Devices : Embedded Processing & DSP Home ● Third Party Collaborative Learning and Development ● Blackfin Online Learning and Development (BOLD), Workshops and Seminars, University Progr.
Analog Devices : Embedded Processing & DSP : Technical Support : Technical Library View Cart | My Account | Log In Home > Embedded Processing & DSP > Technical Support Contact Us | Print.
Analog Devices : Embedded Processing & DSP : Technical Support : Technical Library Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc. All Rights Reserved. This site is optimized for IE 6.
Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools View Cart | My Account | Log In Home > Embedded Processing & .
Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools ADSP-BF534 ADSP-BF536 ADSP-BF537 - Audio Starter Kit - BF537 EZ-KIT .
Analog Devices : Embedded Processing & DSP : Blackfin : Evaluation and Development Tools : Blackfin Processor Development Tools Privacy/Security myAnalog Contact ADI Site Map Registration Technical Support Terms of Use © 1995-2008 Analog Devices, Inc.
デバイスAnalog Devices ADSP-BF538Fの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Analog Devices ADSP-BF538Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAnalog Devices ADSP-BF538Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Analog Devices ADSP-BF538Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Analog Devices ADSP-BF538Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Analog Devices ADSP-BF538Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAnalog Devices ADSP-BF538Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Analog Devices ADSP-BF538Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAnalog Devices ADSP-BF538Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。