Kenmoreメーカー7146611の使用説明書/サービス説明書
ページ先へ移動 of 20
INSTALLATION MANUAL If you have questions when installing, operating or main- taining your filter, and when setting the timer, call this toll-free number... 1-800-426-9345 SAVE THIS MANUAL Kenmore Water Filters Printed on recycled paper Sears, Roebuck and Co.
INTRODUCTION I ] This manual gives you the steps needed to install your new Sears Kenmore Water Filter. To better understand how the water filter is installed, and to know what you will need, please read this entire manual before beginning.
TABLE OF CONTENTS I SECTION 1 BEFORE INSTALLING CHECKS AND TESTS A. SAFETY GUIDES B. UNPACKING THE WATER FILTER C. WATER SYSTEM TESTS PAGE NO. 4 5 6 SECTION 2 PLAN YOUR INSTALLATION A. WHERE TO INSTALL THE FILTER B. TOOLS, PIPE AND FITTINGS, OTHER MATERIALS NEEDED C.
SECTION 1 I BEFORE INSTALLING CHECKS AND TESTS 1A. SAFETY GUIDES • Read all steps, guides and rules carefully before installing and us- ing your new water filter. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property dam- age.
SECTION 1 I BEFORE INSTALLING CHECKS AND TESTS lB. UNPACKING THE WATER FILTER Packed with the filter are installation and owners manu- als, an electrical transformer and a bag of several small parts. Automatic Iron Filter models also include a feeder valve and the other parts shown below.
SECTION 1 I BEFORE INSTALLING CHECKS AND TESTS 1C. WATER SYSTEM TESTS HAS YOUR WATER SUPPLY HAD A CHEMICAL ANALY- SIS? Please see page 2. CHECK YOUR WATER PRESSURE - For your filter to work correctly, a water pressure of no lower than 20 pounds per square inch (psi) is needed in the house wa- ter pipes.
SECTION 2 I PLAN YOUR INSTALLATION 2A. WHERE TO INSTALL THE FILTER Think of the following points as you choose a place to put your filter (See Figure 1). • Place as close as possible to the pressure tank (well water) or water meter (city water). • Place as close as possible to a water drain such as a floor drain, laundry tub, sump or standpipe.
SECTION 2 I PLAN YOUR INSTALLATION 2B. TOOLS, PIPE AND FITTINGS, OTHER MATERIALS NEEDED You must first decide how to run in and out pipes to the filter.
SECTION 2 PLAN YOUR INSTALLATION I I 2C. (_ IN AND OUT PLUMBING USING A 3 VALVE BYPASS (SOLDERED OR CPVC PLASTIC) o_ts_de III T FI'__ Shut-off L [11 'ves III FITTINGS[ '. I II 90" Elbow (4) I I II T.ee (2) I I II I P,pe/a, re .) I Ill F ~l-.
SECTION 3 I PUT THE AUTOMATIC IRON FILTER TOGETER I 3A. ASSEMBLE FEEDER VALVE AND BOTTLE, CONNECT TO MINERAL TANK IF INSTALLING A CLARIFIER, NEUTRALIZER OR TASTE & ODOR FILTER, SKIP THIS PAGE AND GO TO PAGE 11.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL I 4A. ASSEMBLE INLET-OUTLET ADAPTORS, OR PLASTIC BYPASS VALVE 1. Close the shut off valve on the house main water pipe, near the water meter or pressure tank, to turn off the wa- ter. 2. Shut off the gas or electric supply to the water heater.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 4B. INSTALL THREE VALVE BYPASS 1. INSTALLING THREE VALVE BYPASS AND PIPES (FIGURE 8). a. Cut the house main water pipe where you will connect the filter. Loosely put together pipe, fittings and the three valves.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 4C. LOCATE FILTER AND CONNECT PIPES 1. MOVE THE FILTER INTO PLACE Carefully rock the filter, back and forth, and move the filter into position. So the filter stands straight, be sure the sur- face it sets on is level and smooth.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 4D. CONNECT DRAIN HOSES 1. CONNECT THE VALVE DRAIN HOSE Attach a length of 5/8" minimum inside diameter hose to the filter and run to the floor drain or other suitable drain point. Other suitable drains include a laundry tub, sump, or a standpipe.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 4D. CONNECT DRAIN HOSES IF INSTALLING A CLARIFIER, NEUTRALIZER OR TASTE & ODOR FILTER, SKIP PAGE 15 AND GO TO PAGE 16. 2. CONNECT THE BOTTLE DRAIN TUBING AUTOMATIC IRON FILTER Connect a length of 5/16" plastic tubing to the vent fitting on the feeder valve (Figure 11) using a nut ferrule.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 4E. PRESSURE TEST - CHECK FOR LEAKS TESTING YOUR PLUMBING WORK FOR WATER LEAKS. CAUTION: TO AVOID WATER OR AIR PRESSURE DAMAGE TO FIL- TER INNER PARTS, ATTO FLUSH PIPE CHIPS OR OTH- ER RESIDUE FROM THE WATER PIPES, BE SURE TO DO THE FOLLOWING STEPS EXACTLY AS INSTRUCTED.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL 41=. GROUNDING, CONNECT TO ELECTRICAL POWER 1. INSTALL GROUNDING WIRE BETWEEN THE FIL- TER IN AND OUT PIPES The house cold water pipe (iron or copper) is often used to ground all electric outlets in the home.
SECTION 4 I STEP BY STEP GUIDES TO INSTALL RESTART THE WATER HEATER TURN ON THE GAS (OR ELECTRIC) SUPPLY TO THE WATER HEATER AND LIGHT THE PILOT. NOTE: Your new Sears filter is now filtering the water for your household needs. However, your WATER HEATER is filled with unfiltered water.
19.
20.
デバイスKenmore 7146611の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kenmore 7146611をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenmore 7146611の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenmore 7146611の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenmore 7146611で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenmore 7146611を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenmore 7146611の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenmore 7146611に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenmore 7146611デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。