KenwoodメーカーDPX-6030の使用説明書/サービス説明書
ページ先へ移動 of 44
DPX-6030 DPX-6020 © PRINTED IN JAPAN B64-2004-10 (M) (+) 03/ 2 1 02/12 11 10 9 8 7 6 5 4 3 2 DOUBLE DIN SIZED CD/CASSETTE RECEIVER INSTR UCTION MANU AL.
— 2 — English Contents Safety precautions ..........................................................3 Handling Compact discs .................................................5 General operations Power ..............................................
— 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery, or ground wires, make sure to use automotive- grade wires or other wires with a 0.
English • CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD- R/CD-RW writing software or CD-R/CD-RW recorder.) Additionally, depending on the recording status, it may prove impossible to play certain CDs recorded on CD-R or CD-RW.
— 5 — Handling Compact discs Playing a CD that is dirty, scratched or warped can cause the sound to skip and the unit to operate incorrectly, resulting in worsened sound quality. Take the following precautions to prevent your CDs from getting scratched or damaged.
Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: Selecting standby mode: Press the SRC button repeatedly and switch to "ALL OFF". When "ALL OFF" is displayed, the standby mode is activated.
This function allows you to turn down the volume quickly. Turning Attenuator On/Off: Press the ATT button to switch the attenuator on and off. When the attenuator is on, the ATT indicator blinks. When the attenuator is off, the volume returns to the original level.
— 8 — English You can adjust the panel angle for easy viewing. Sliding the panel: Press the ANGLE ∞ button. Each time you press the ANGLE ∞ button, the panel will slide one step at a time.The faceplate angle can be varied in up to ten steps. If the power is turned off, the panel will close automatically.
— 9 — T uner features CRSC SRC 38 DISP/ NAME #1~6 SBF 4 ¢ FM AM DISP ST indicator indicator Frequency Band display Preset station number AUTO indicator Store the frequency of a station. You can then recall that station with a single touch of a button.
Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. The indicator lights up when CRSC is off. Turning CRSC On/Off: Press the CRSC button for at least one second to turn the function on/off.
Continue steps 3 and 4 until all the characters are chosen for the name. You can enter up to 8 characters for each name. Assigning Names Press the NAME button on the unit or the OK button on the remote. The name of the station is stored in memory, and the Station Name Preset mode ends.
Cassette player features You can search for the station for any station if its name has been preset using Station Name Preset. Press the SBF button for at least one second. “SBF SNPS” will be displayed once the station name preset play mode is entered.
Loading and Playing Cassettes: Press the CASSETTE EJECT button to slide open the front panel, showing the cassette (insertion) slot. Holding the cassette with the tape exposed to the right, insert in the slot. The front panel will close, and the tape will start playing.
Automatically fast forward to the beginning of the next track when long blank spaces (10 seconds or more) are detected, continuing tape playback. The B.S indicator lights up when blank skip is turned on. Turning Blank Skip On/Off: Press the B.S button to switch blank skip on and off.
Switching the display during the tape mode: Each time you press the DISP button, the display switches as follows: The tape counter is not exact, but only represents an approximation of the elapsed time. NOTE Tape counter "Character" "Clock" Switching Display Repeatedly plays the track currently being listened to.
— 16 — English CD/External disc control features CD EJECT SRC 38 DISP/ NAME 4 ¢ DISC+ DISC- SCRL RDM D.SCN SCN REP M.RDM SBF DISP indicator RDM/M.RDM indicator SCN/D.SCN indicator REP/D.REP indicator Mode display/ Disc number Track time Track number Play: Press the CD EJECT button to slide open the front panel, showing the CD (insertion) slot.
— 17 — • Do not apply excessive force to the front panel after it slides. • Do not use the unit with the front panel in the slid condition. Doing so will cause breakdown. When you load a CD and eject it right away, the next time you try to insert the CD may not load.
— 18 — English CD/External disc control features Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. Reversing Disc Play: Hold down on the 4 button. Release your finger to play the disc at the point.
— 19 — You cannot use the direct track search function while doing track or disc scans or using random or magazine-random play. NOTE Using the remote, directly input the disc number that you want to listen to. Using the number buttons on the remote, input the number of the disc that you want to listen to.
Play the tracks on all the discs in the disc changer in random order. Press the M.RDM button to switch magazine random play on and off. The M.RDM indicator lights up when magazine random play is turned on. The disc and track numbers will change over and over in the display as the next track is being selected.
— 21 — display after inserting a disc magazine, try playing it using the disc scan or a similar function to display the disc name. Also note that "No Access/No Disc" will be displayed when a disc has not been loaded. Rapid display (forward / reverse): Press the DISC + or DISC – button.
Direct Alphabet Input (Function of remote) You can directly input letters using the number/letter entry buttons on the remote. Example: Use the following table to enter the name "DANCE". Continue steps 3 and 4 until all the characters are chosen for the name.
— 23 — DSP features 4 ¢ FM AM #2 #1 DSP/OFF COMP #3 SFC POSI/ R.SIZE DISP DSP indicator Sound field control name.
— 24 — English DSP features A DSP is a device which uses digital control to correct the audio signal and produce sound effects that can compensate for the small passenger compartment of a vehicle. The DSP indicator lights up when the DSP is on. Turning the DSP On: Press the DSP button.
— 25 — This function can compress the dynamic range of music, so that low sounds which are covered over by road noise can be raised. Press the DSP button. "DSP CTRL" is displayed once the DSP control mode is entered. The DSP indicator blinks during the DSP control mode.
— 26 — English DSP features Up to three sets of the DSP settings and conditions you adjusted can be stored in the memory, and then you can recall them with the single touch of a button. Press the DSP button. "DSP CTRL" is displayed once the DSP control mode is entered.
— 27 — This mode allows you to call up the preset equalizer curves, adjust the graphic equalizer, make the setting of the spectrum analyzer, and so on. Turning the Graphic Equalizer Mode On: Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered.
— 28 — English Graphic Equalizer features You can select the display to enjoy sounds with eyes. Switching the Preset Spectrum Analyzer Display: Press the EQ button. "EQ CTRL" is displayed once the Graphic equalizer mode is entered. Press the DISP button.
— 29 — Function set system To accommodate a greater number of functions, a function set system has been employed for making settings. Press the FNC button to enter the function set mode and then display the function to make the setting. Select the mode that you want to make the setting of the function.
Function set system — 30 — English Function items in Standby mode: This function produces a beep sound that accompanies button operation. It can be switched on or off. Display and setting ”BEEP On“ ”BEEP Off“ 1. Touch Sensor Tone Switch the preout between the rear and non-fading.
— 31 — Press the 38 button. The security code will be set. "CODE ✽✽✽✽ 1" appears in the display, asking you to enter the code once again for confirmation, and then you can start inputting the code. Press the Preset button and input the security code again.
— 32 — English Function set system You can select the frequency to be cut of the high pass filter for rear output. Display and setting “HPF-R Off/30/60/90/120/150/180/250” (Hz) 2. Frequency Setting of High Pass Filter for Rear Output You can select the filter slope of the high pass filter.
— 33 — <In Tuner mode> Select which tuning mode — auto seek or manual — to use as the default. When the AUTO indicator is on, auto seek tuning is selected. When the indicator is off, manual tuning is selected. Display and setting "Auto Seek": auto seek mode "Manual Seek": manual tuning mode 10.
• VOLUME buttons Basic operations Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two “AAA”-size batteries. Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the + and – poles aligned properly, following the illustration inside the case.
• Number/letter entry buttons Press buttons #1-6 to recall preset stations. During direct access tuning, use these buttons to input the frequency of the station. Use to enter letters (alphabetical) during station name preset. • 4 / ¢ (TUNE) buttons Press the 4 button to decrease the frequency.
• Number/letter entry buttons Used to specify the track (disc) number used in direct track (disc) searches. Use to enter letters during disc name preset. • 4 / ¢ buttons Press the 4 button to search through the tracks backward. Press the ¢ button to search through the tracks forward.
— 37 — Accessories .........6 1 .........1 2 .........1 3 External view ......... Number of items The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above.
— 38 — English – + – + – + – + – + 10 ANT CONT P.CONT FRONT•L FRONT•R REAR•L REAR•R EXT. CONT. ILLUMI Connecting Wires to Terminals When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear).
— 39 — Installation ■ Installation (for TOYOTA, NISSAN Car etc.) When performing a check of the CD operation prior to installation, place this unit in a hirizontal position and perform a loading/eject of the CD. 2 CAUTION Install onto the car bracket using the supplied screws (M5 × 6 mm, M5 x 7 mm).
— 40 — English What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM The tape head is dirty.
— 41 — SOLUTION POSSIBLE CAUSE PROBLEM A CD ejects as soon as it is loaded. The CD is upside-down. Load the CD with the labeled side up. The memory is erased when the ignition is turned off. The battery wire has not been connected to the proper terminal.
The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. Load the disc magazine properly. ] EJECT No disc has been loaded in the disc magazine.
— 43 — Nothing has been recorded on the MD. Blank Disc No disc has been loaded in the disc magazine. Load a disc into the disc magazine. The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. Clean the CD and load it correctly. ] ] Error 04 No tracks are recorded on the MD, although it has a title.
— 44 — English FM tuner section Frequency range (50 kHz space) ................................87.5 MHz – 108.0 MHz (200 kHz space) ..............................87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) ....................9.3dBf (0.
デバイスKenwood DPX-6030の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kenwood DPX-6030をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenwood DPX-6030の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenwood DPX-6030の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenwood DPX-6030で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenwood DPX-6030を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenwood DPX-6030の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenwood DPX-6030に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenwood DPX-6030デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
