KenwoodメーカーKRC-28MRの使用説明書/サービス説明書
ページ先へ移動 of 25
KRC-208S KRC-218 KRC-28MR © B64-1538-00 (KW) CASSETTE RECEIVER INSTRUCTION MANUAL AMPLI-TUNER-LECTEUR DE CASSETTE MODE D’EMPLOI RADIO CASETE MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual.
— 2 — English Contents Before use Safety precautions ........................................................................3 General features Power ............................................................................................5 Switching Modes .
— 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery, or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer.
Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: Selecting standby mode: Press the SRC button repeatedly and switch to "OFF" . When "OFF" is displayed, the standby mode is activated. The standby mode turns all functions off while leaving the power to the unit on.
"BAL" : Adjust the balance level. Setting values: Left 15 – Right 15 "TRE" : Adjust the treble level. Setting values: - 4 – + 4 "BAS" : Adjust the bass level. Setting values: - 4 – + 4 Press the AUD button for at least one second to enter the control mode.
Adjust the time. When the time is not displayed, first press the CLK button to display the time. Press the CLK button for at least one second to enter the clock adjustment mode. The time display will blink. • Adjusting the hours Press the FM button to advance the hours, or press the AM button to make the hours go back.
T uner features The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate: Press the release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts.
You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available.
Cassette player features Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. The factory default for this function is ON. Turning CRSC On/Off: Press the CRSC button for at least one second to turn the function on/off.
Switch automatically to the tuner while you are rewinding or fast forwarding the tape. Turning Tuner Call On/Off: Press the T.C(T.CALL) button to switch tuner call on and off. The T.CALL indicator lights up when tuner call is turned on. Tuner Call Fast Forwarding Tapes: Press the FF button.
Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Disc Play This function permits the connection of optional players and the playing of discs. Playing Discs: Press the SRC button repeatedly to select the external disc control mode.
Repeat playing the track or the disc currently being listened to. Turning Repeat Play On/Off: Press the REP button to switch repeat track/disc play on and off as follows: The REP indicator lights up when repeat play is turned on. The track number blinks in the display when track repeat is on.
Play the tracks on all the discs in the disc changer in random order. Press the M.RDM button to switch magazine random play on and off. The RDM indicator lights up when magazine random play is turned on. The disc and track numbers will change over and over in the display as the next track is being selected.
To change the track being heard, press the ¢ button. Another disc/track will be selected and played. • Magazine random play is canceled when you eject the disc. • The time needed for random selection depends on the number of discs loaded in the disc magazine.
English — 16 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2 CAUTION Accessories ..........................................1 .
FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT. — 17 — Connecting Wires to Terminals When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear).
English — 18 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). NOTE Accessory 2 Metal mounting strap Self-tapping screw (commercially available) Firewall or metal support Accessory 4 Installation ■ Installation 8 mm MAX.
— 19 — Installation Removing the hard rubber frame ■ When the lower level is removed, remove the upper two locations. 2 The frame can be removed from the top side in the same manner. NOTE Catch Lock Engage the catch pins on the removal tool and remove the two locks on the lower level.
English — 20 — Installation Accessory 7 Screwing the Faceplate on the Unit (KRC-208S / 218 only) ■ Never insert the taptite screw ( ø 4 × 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit.
— 21 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. Troubleshooting Guide SOLUTION POSSIBLE CAUSE PROBLEM The tape head is dirty.
English — 22 — Troubleshooting Guide External disc control mode The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p.4). The disc control mode cannot be selected. No wire has been connected to the disc changer input terminal on the unit.
— 23 — Troubleshooting Guide The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. Nothing has been recorded on the MD. ] The next MD will automatically be played. E-10 No disc magazine has been loaded in the changer.
English — 24 — Specifications subject to change without notice. Specifications FM tuner section Frequency range (200 kHz space) .............87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) .....................9.3dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .
KRC-208S_U.S-1 00.12.26 4:00 PM Page 25.
デバイスKenwood KRC-28MRの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kenwood KRC-28MRをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenwood KRC-28MRの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenwood KRC-28MRの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenwood KRC-28MRで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenwood KRC-28MRを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenwood KRC-28MRの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenwood KRC-28MRに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenwood KRC-28MRデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
