KenwoodメーカーLZ-701Wの使用説明書/サービス説明書
ページ先へ移動 of 18
LZ-701W 7-inch WIDE SCREEN MONITOR INSTRUCTION MANUAL MONITEUR GRAND ECRAN 7 pouces MODE D’EMPLOI 7-Zoll BREITBILD MONITOR BEDIENUNGSANLEITUNG 7 inch BREEDBEELDMONITOR GEBRUIKSAANWIJZING MONITOR A S.
English 2 Contents Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Switching the Monitor’ s Picture .
3 Safety Precautions To prevent injury and/or fire, take the following precautions: • Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. • When extending the ignition or ground wires, make sure to use automotive-grade wires or other wires with an area of 0.
English 4 Operation Power Tu rning on the power Press the V .SEL button. Tu rning off the power Press the V .SEL button for at least two seconds. Switching the Monitor’ s Picture <When the KTC-V800N or KTC-V800P is connected> Each time you press the V .
5 Y ou cannot operate when the navigation picture is displayed. <When the KTC-V800N or KTC-V800P is connected> Adjusting the Picture Quality Press the SCRN button, the picture quality adjustment screen to be displayed. Each time you press the SCRN button, the adjustment item can be selected.
Selecting the Channels <When the KTC-V800N or KTC-V800P is connected> Auto Seek Mode (AUTO1) Press the [ 3 ] button to seek for channels up the band. Press the [ 2 ] button to seek for channels down the band. Preset Station Seek Mode (AUTO2) Press the [ 3 ] button to move to the next preset station.
Selecting the Seek Mode [SEEK MODE] <When the KTC-V800N or KTC-V800P is connected> Y ou can choose from three seek modes: auto seek, preset station seek, and manual seek.
Setting the Remote Sensor On/Off [REMOTE] If this unit also runs when operating other units with different Kenwood remote controls, its remote control function can be turned off.
9 Remote Control Function <Provided with the KTC-V800N/KTC-V800P> Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries 1. Use two "AA" batteries: Slide the cover while pressing downwards to remove it as illustrated.
English 10 Installation Accessories External view ......... Number of items ........1 1 ........1 2 ........1 3 External view ......... Number of items ........5 4 ........2 5 (Ø4 x 12 mm) (Ø4 x 16 mm) Installation Procedure 1. T o prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery .
11 • Be sure to use the supplied screws for installation. Using screws longer than those supplied may destroy parts inside the unit causing it to smoke. Using screws shorter than those supplied may cause the unit to come looks from the installation bracket.
English 12 Installation Installation for Monitor Unit Installation location and cleaning Select for installation a location where the stand can be placed completely horizontal or where the front edge of the support (petal-shaped part) can be attached horizontally as shown in Figure A .
13 Accessory 3 Accessory 4 (Ø4 x 12 mm) Protective strip Loosen T ighten T ighten Loosen Installation surface IM_W_English_ver.5 02.12.20 1:38 PM Page 13.
English 14 Installation Installation for the Video Box Unit Accessory 5 (Ø4 x 16 mm) IM_W_English_ver.5 02.12.20 1:38 PM Page 14.
15 – + TO MONITOR UNIT VIDEO IN VIDEO OUT POWER PRK SW ACC FM TX +12 V 2 AV INPUT AV OUTPUT 1 AV INPUT ANTENNA Connection Accessory 2 Accessory 1 Ignition wire (Red) ª 12V Parking sensor wire (Green) For the sake of safety , be sure to connect the parking sensor .
English 16 Tr oubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. SOLUTION POSSIBLE CAUSE PROBLEM Nothing happens when the buttons are pressed.
17 Specifications Specifications subject to change without notice. Monitor Unit Screen size ....................................................................................7.0 inches wide 154.1(W) x 87.05(H) x 177(Diagonal) mm 6-1/16(W) x 3-7/16(H) inch Display system .
LZ-701W(E)_00Cov_m2 02.12.20 1:39 PM Page 2.
デバイスKenwood LZ-701Wの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kenwood LZ-701Wをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKenwood LZ-701Wの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kenwood LZ-701Wの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kenwood LZ-701Wで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kenwood LZ-701Wを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKenwood LZ-701Wの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kenwood LZ-701Wに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKenwood LZ-701Wデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。