Keys FitnessメーカーStrength trainer ST-1000の使用説明書/サービス説明書
ページ先へ移動 of 32
O O W W N N E E R R ’ ’ S S O O W W N N E E R R ’ ’ S S M M A A N N U U M M A A N N U U A A L L A A L L Questions? Call our toll free Keys Fitness Helpline 1-800-683-1236 ST-1000 H OME G YM.
V THANK Y OU for making this Strength T rainer unit a part of your exercise program. Keys Fitness and our Strength T rainer Series assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process.
BEFORE Y OU ST ART Prior to assembly , remove components from the box and verify that all the listed parts were supplied. Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems.
PA R T S Y.
PA R T S Z.
[ PA R T S.
PA R T S .
P ARTS LIST ] # DESCRIPTION QTY 1 Base Frame 1 2 Foot Plate 1 3 Main Upright 1 4 Rear Cross Beam 1 5 Rear T op Beam 1 6 Main T op Beam 1 7 Foot Plate Bracket 1 8 Lat Pull Down Bar 1 9 Seat Pad Support.
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. ^ Do not use bolt here yet. W ait for STEP 6. Do not use bolt here yet.
u ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
` ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. a Feed Cable (63) through framework as pictured. Hold cable in place by placing in pulley grooves and bolting pulleys to frame.
ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. 11 First, insert guide rods into rear cross beam (4). Then slide on, from top to bot- tom, rubber bushings (125), 19 weight plates (128) and weight plate assembly (50).
12 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
13 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
14 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
15 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Hex Screws (109) are already pre-assembled for you. Make sure to unscrew them before sliding in shafts (43).
16 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws (109) are already pre-assembled for you. Make sure to uncrew them before sliding in shaft(39).
17 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Note: Hex screws are already pre-assembled for you. Make sure to unscrew them before sliding in shaft (39).
18 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
19 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
20 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
21 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
22 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
ASSEMBL Y 23 NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 24 Feed cable (62) through framework as pictured. Hold cable in place by setting in pulley grooves and bolting pulleys to frame or as pictured. View finished assembly of this step in future steps or on cover page for guidance.
24 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Feed remaining section of cable (63) through leg press framework.
25 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Feed cable (64) through framework. Hold cable in place by setting in pulley grooves and bolting pulleys to frame.
26 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled..
27 ASSEMBL Y NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Before securing weight stack covers (25,26): 1. Make sure to lightly lube the guide rods with the supplied lubrication. 2. Place the weight stack plate numbers on the weight plates.
28 EXPLODED VIEW.
KEY S FITNESS PRODUCTS, L.P . STRENGTH TRAINER SERIES LIFETIME WARRANTY This Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period to the original purchaser is lifetime of the original purchaser .
Keys Fitness Products, L.P . 4009 Distribution Drive, Suite 250 Garland, T exas 75041 Customer Service: 1-800-683-1236.
デバイスKeys Fitness Strength trainer ST-1000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Keys Fitness Strength trainer ST-1000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKeys Fitness Strength trainer ST-1000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Keys Fitness Strength trainer ST-1000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Keys Fitness Strength trainer ST-1000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Keys Fitness Strength trainer ST-1000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKeys Fitness Strength trainer ST-1000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Keys Fitness Strength trainer ST-1000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKeys Fitness Strength trainer ST-1000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
