KitchenAidメーカー1435の使用説明書/サービス説明書
ページ先へ移動 of 16
- Installation Instructions 30” Built-In Microwave Convection Hood L IMPORTANT: Installer: Leave Installation Instructions with the Homeowner. Homeowner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use.
30” BUILT-IN MICRO WAVE /HOOD MODEL KHMC106 W INSTALLATION INSTRUCTIONS CONTENTS: Introduction ....................................................................... 1 Mounting Space .................................................................
INTRODUCTION Proper installation is the installer’s responsibility. A qualified technician should install this microwave oven. Make sure you have everything necessan/ for correct installation. It is the responsibility of the installer to comply with the installation clearances specified on the serial/rating plate.
WALL CONSTRUCTION Personal Injury or Property Damage Hazard l This microwave oven must be mounted against and supported by a flat, vertical wall. l This microwave oven must be attached with two lag screws to a minimum of one, vertical 2” x 4” wall stud.
ELECTRICAL REQUIREMENTS Electrical ground is required on this appliance. E-&~&Hazard l Checkwithaqualifiedelectricianifyouareindoubtastowhethertheapplianceisp~perlygrounded. Improper connection of the equipment-grounding conductor can result in electrical shock.
HOOD EXHAUST DUCT When the hood is vented to the outside, a HOOD EXHAUST DUCT is required. All ductwork must be metal (do not use plastic duct). Check that all connections are made securely. Please read the following carefully: Fire Hazard Mntirg system must terminate to the outside.
TOOLS RECOMMENDED FOR INSTALLATION Phillips Screwdriver Electric Drill l/2”, 5/8” and 3/32’ Drill Bits 1 -l/2’ Wood Bit or metal hole cutter (if metal cabinet is used) Saw to cut exhaust opening (if needed) Knife or single edge razor Pencil Measure Tape Protective drop cloth for product and range.
PREPARATION OF CARTON Utilization of the canon may make installation easier. CHECK THE PRODUCT FOR DAMAGE 1. Remove product and shipping pads. Visually check the product after removing from carton. Remove all packing material from inside the oven cavity.
VENTILATION SYSTEM THIS MICROWAVE OVEN/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THREE TYPES OF HOOD VENTILATION SYSTEMS: A. Vertical Exhaust -- outside ventilation B. Horizontal Exhaust -- outside ventilation C. Recirculating -- non-vented, ductless Select the type required for your installation.
HORIZONTAL EXHAUST (Continued) 2. Withdraw hood fan unit upward carefully (Fig.4). Figure 4 1. 3. Rotate hood fan unit l/4 turn as shown in Figure5 Figure 5 4. Replace hood fan unit into the oven unit. Be careful not to pinch the lead wire between the inner bracket and the hood fan unit (Fig.
1 ,, .:y 2. -- .; . . . -A.,~*;-,-, .-. 5. Replace the fan cover bracket. Make sure the fan blades are visible through the rear openings in the cover before proceeding. Attach cover to unit with 3 screws (Fig. 7). The hood fan unit is now rotated for horizontal exhaust operation See page 11 for exhaust adaptor assembly installation instructions.
PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES.
5. If horizontal exhaust is used, attach the exhaust adaptor assembly to each of the mounting plates by aligning the holes on the assembly with the tabs on the plates, holding the as- sembly in place and bending the tabs to secure the assembly to the plates (Fig.
Thread the oower sunulv cord throueh the hole made at the bottom of the ton cabinet I Personal Injury Hazard Two people are required to lift this microwave. Failure to use more than one person during installation may result in oersonal iniurv. I Hang the unit on the lower edge of the mounting plates.
8. Use the two top cabinet mounting screws (C) and flat washers (D), supplied in the installation hardware, to attach the unit to the top cabinet. See Figurel6. Note: If mounting plates were installed using only toggle bolts, use the adjusting screws to attach the unit to the top cabinet.
4 I-? 4S72 PART NO. KHMCIOGW PRINTED IN U.S.A..
デバイスKitchenAid 1435の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
KitchenAid 1435をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKitchenAid 1435の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。KitchenAid 1435の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。KitchenAid 1435で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
KitchenAid 1435を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKitchenAid 1435の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、KitchenAid 1435に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKitchenAid 1435デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。