KitchenAidメーカー9743822の使用説明書/サービス説明書
ページ先へ移動 of 22
I itChenAid ® HOME APPLIANCES APPAREILSI_LECTROM_:NAGERS www.kitchenaid.com _---------._ Quick Reference Section Introduction Page 2 Product dlmenslons 3 Bullt-ln opening dlmenslons 3 Electrical req.
In_on s_s cont fmm _ s If connecting dishwasher with power supply cord, check that power supply is dlsconne_ed. Electrical ShockHazard Plug Into a grounded 3 prong outlet. Do not removegroundprong. Do not use an adapter. Do not use an extanslon cord. Failure to followthese Instructions can result In death, fire, or electrical shock.
® A. electric drill B. Phillips screwdriver C. flat-blade screwdriver D. 2 adjustable wrenches E. pliers F. measuring tape or ruler G. pipe wrench H. hole cutters (1/2", 3/4", t-ln") 1. tubing cutter J. wire stripper K. utility knife L.
/ (6xem) 34"(S6._) Unshaded area must be free of pipes, wires and drain hose. Power supply cord or cable should not be kinked or pinched betwom dishwasher and cab'met. Leveling legs and wheels adjust to fit 34-inch (86.4cm) to 35-inch (88.9cm) cabinet opening height.
• The hot water line to the dishwasher must provide between 20-125 psi (138-862 kPa) water pressure. • The hot water heater should be set to deliver 120°F (49°C) minimum water temperature to the dishwasher for best results. • A 3/8" minimum O.
Direct wire method Local codes may permitusing armored or non-metallic sheathed, copper wire(A) (withground wire) to connect dishwasher to unction box. 5. Cut a 3/4"(l.gcm) hole in la_, side or floor of cabinet(B) for direct wiring. Right side is easiestlocation.
Adjust the frout leveling legs (E) the number of turns listed in the chart. The dishwasher should be installed as level as possible from front to back. Put the spring-type drain hose clamp (F) over the drain connector (G). Push drain hose (H) onto drain connector.
Altemate Connection Methods No Air Gap If local codes permit, the dishwasher drainhose may be connected direcOy to awaste tee or waste dispo . Drain hose (A) to waste tee (B) Cut drain end of drain hose as shown (C). Do Not cot fibbed section to shorten drain hose (D).
• Install a U.L-listed/t_-certilied strain relief(F) to the terminal box. Run power supply wire through strain relief, ff using conduit, use a U.L.-listed/CA_-cer tiffed conduit connncmr. Run conduit through connector. • Connect the whitewire (G) from the power supplywire to the whitewire in the terminal box with twist-on wire connector.
• Connect the white wire (Q) from the powersupply cord to the white wirein the terminal box with twist-on wireconnector. • Connect the black _ (R) fromthe power supply cord to the black wire in the terminal box with twist-on wire connector.
O Open door about 3 inches (7.6cm) and check for equal spacing (C) between inner door and tub sides. If spacing is not equal, loosen bracket screws and shifttub. Tighten bracket screws. Remove newstraper or towel from dishwasher. Open and close door several times.
access and lower panelto dishw_her so that the bottom edge of the lower panelcontacts the floor. Your installation is now complete. Keep Installation Instructions and Use and Care Guide close to dishwasher for easy reference.
n Your safety and the safety of others is very Important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.
Introduction cont. from page2 MODELS A MODI_LIES KUDC Series Stifle KUDC 24-1/4" (61.6 ore) 10UDI25 Series 61,6 cta (24-1/4 po) Sl_de KIJDI25 All Others 25-1/4" (64.1 an) TOllS lea anwes 64,1 can (25-1/4 po) * does not include insulation bhmket * ne comprend pas l'isolant 35-7.
O} Ill It is the customer's responsibility:. To contact a qualified electrician. To assure that the electrical installation is adequate and in conformance with all national and local codes and ordinances. Dishwasher must be connected to theproper electricalvoltage and flequency as specified on the model/serial rating plate.
/ 24,,'''_ (61_m) ElectricalShock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. 1. Disconnect the power supply. 2. Put on gloves and safety glasses.
Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. Excessive Weight Hazard Use two or more people to move and Install dishwasher. Failure to do so can result in back or other injury.
(I r ! I'1 Connect drainhose to an air gap or waste tee using one of the recommended or alternate methods. Recommended Connection Methods Install Air Gap Kit (Part No. 300096) (A) according to kit instructions. If a different air gap is used, it should be checked to make sure it allows for the same air flow.
o Apply Teflon tape to 90 ° elbow fitting (A) and connect fitting directly to water inletvalve (B). Attach water supply line (C) to fitting. Do Not allow the water pipe or tubing to contact the motor or dishwasher legs (D). Turn on watersupply and check for leaks.
Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. Open dishwasher door and removeall shippingmaterials.
Check that all parts have been installed (except access and lower panels) and no steps were skipped. _ Check that you have all the tools you used. Read the Use and Care Guidethat came with your dishwasher. ,,Reconnec, t, power supply to dishwasher. Set the dishwasher to run the 'Normal' cycle.
The KltchenAid Consumer Assistance Center is open 24 hoursa day, 7 days a week. Call1o(800) 422-1230. Thecall is freewithin the continental United Sta_. In Canada, call 1-(800) 461-5681 for English and 1-(800) 461-5703 for French. Call the KitchenAid Consumer Assistance Center when you: • Have questions about dishwasher installationor operation.
デバイスKitchenAid 9743822の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
KitchenAid 9743822をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKitchenAid 9743822の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。KitchenAid 9743822の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。KitchenAid 9743822で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
KitchenAid 9743822を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKitchenAid 9743822の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、KitchenAid 9743822に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKitchenAid 9743822デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。