AntecメーカーSOLO IIの使用説明書/サービス説明書
ページ先へ移動 of 26
S O L O I I U SER M ANUAL S ILENCE R ENEWED.
2 SOLO II U SER ’ S M ANUAL Congratulations on your purchase of the Antec SOLO II. The SOLO II emphasizes Quiet Computing™ and reinvents Antec’s renowned Sona ta line with a new set of attractive, practical features. Externally, the SOLO II’s dual-layer 1.
3 T ABLE O F C ONTENTS S ECTION 1: I NTRODUCTION 1.1 Getting to Know your Chassis ........... .................. ............ ............ ............. 5 1.2 Chassis Specif ications.......... ............. .................... ............ ..........
4 I N T R O D U C T I O N S ECTION 1.
5 1.1 G ETTING TO KNOW YOUR CHASSIS 1. Internal: 3 x 3.5” / 2.5”using tray m ount OR 2 x 3.5” with suspension mount cable s 2. Internal: 1 x 2.5” SSD (dedicated) 3. External: 2 x 5.25” 4. 1 x rear 120 mm TrueQuiet™ fan with 2-speed s witch 5.
6 1.2 C HASSIS S PECIFICATIONS Chassis Type Mid Tower Chassis Color Piano Black Dimensions 17.3” (H) x 8.1” (W) x 18.5” (D) 440 mm (H) x 20 5 mm (W) x 470 mm (D) Weight 20.
7 1.4 B EFORE Y OU B EGIN In order to ensure that your build ing experience with the SOLO II will be a positiv e one, please take note of the following: • While working inside your SOLO II, ke ep your chassis on a flat, stable surfac e. Make sure your build environment is clean, well-lit, and free of dust.
8 H A R D W A R E I N S T A L L A T I O N S ECTION 2.
9 2.1 S ETTING U P Begin by removing the left side panel by lo osening the thumbscrews and swingin g the panel outward, pulling it back towards you; this will completely remove it. Cut the ties on the 5. 25” drive cage with a wire cutter and remove the plastic bag of screws.
10 2.2 M OTHERBOARD I NSTALLATION Before proceeding: Check the manual for your CPU cooler to fin d out if there are steps you must do before installing the motherboard.
11 3. Screw your motherboard into the standoffs with th e provided motherboard mo unting screws. 2.3 I NSTALLING THE KUHLER H 2 O The following instructs how to install the Ant ec KUHLER H 2 O liquid CPU cooler (620 / 920). For any other CPU coolers, please consult your manufac turer’s installation guide.
12 2. The TrueQuiet™ fan has two small black clips attached to the fan’ s two-speed switch. With your thumb and forefinger, spread the clips while pushing from the rear of the case to remove th e switch. 3. Preparing the KUHLER H 2 O backplate is specific to you r CPU socket.
13 2. Remove the second screw with your other han d supporting the beam so the beam won’t drop. 3. Repeat steps 1 and 2 for the support beam screws at the rear of the case. . 4. Place the SOLO II on its side. Position the PSU into the mount and secure it with the PSU screws provided.
14 2.5 C ABLE M ANAGEMENT There is a cable management area b etween the motherboard and right side pan el as well as cable hooks located on the side of the 3.5” drive cage. You c an tuck excess cables in this area or route them to the drive bays. Choose the cables you would like to pass thr ough the holes behind the motherboard tray.
15 2. Attach the drive rails to your 5.25” device. Th ese rails have three depth settings t hat accommodate the depth of your 5.25” drive. 3. Make sure to properly align your drive rails wi th your 5.25” drive. We recommen d attaching one rail with one of the 5.
16 2.7 I NTERNAL 3.5” AND 2.5” I NSTALLATION ( TRAY M OUNTS AND SUSPEN SION MOUNTING SY STEM ) The following text outlines the preparator y stages for installing 3.5” / 2.5” drives u sing drives trays and the suspension mounting system. 1. If you have reattached it, remove the left side pan el.
17 5. Insert the 3.5” / 2.5” drive into the drive cage by pinch ing the ends of the drive tray and sliding the tray along the rails until the tray l ocks firmly into position. 6. Mount any other 3.5” / 2.5” devices accordingly. For Suspension Mounting Installation: The SOLO II accommodates two 3.
18 4. Twist the rear suspender and gu ide the hard drive through it. 5. Find the appropriate power connector on the PSU an d connect it to the device. 6. Repeat the same procedure for a second dri ve if necessary. 7. Close and secure the drive cage door.
19 F RONT I/O P ORTS S ECTION 3.
20 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connecti on) 10 Empty Pin 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard .
21 Pin Signal Na me s (HDA ) Pin Signal Na me s (AC’9 7) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MICP o wer 4 AVC C 4 N C 5 FRO -R 5 Lin e Out (R) 6 MIC 2_ JD 6 Lin e Out (R) 7 F_ IO_ SEN 7 N C 8 Key(no pi n) 8 Key(no pi n) 9 FRO-L 9 Lin e Out (L) 10 LINE 2_JD 10 Lin e Out (L) 3.
22 3.5 R EWIRING M OTHERBOARD H EADER C ONNECTIONS There may come a time wh en you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB he ader, audio input header, or some other front panel connector such as the Power Button c onnector.
23 C OOLI NG S YSTEM S ECTION 4.
24 4.1 I NCLUDED 120 MM T RUE Q UIET ™ REAR FAN The SOLO II co mes with a 120 mm TrueQuiet™ rear fan. This fan h as a two-speed switch t hat lets y ou cho ose the speed be st suited to y our need. The switch is located at th e rear of the ca se. The d efault fan speed sett ing is Low.
25 4.3 O PTIONAL F ANS The SOLO II can accommodate two 1 20 mm front intake fans. The following sho ws you how to install one of thesefans using a 120 mm TrueQuiet™ fan: 1. Remove the fan filter as depicted in secti on 4.2. 2. Insert the mounting pin through the mounting hole tail-first.
26 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1 200 fax: 510-770-1 288 Antec Eur ope B .V. Stuttgartstra at 12 3047 AS Rott erdam The Netherland s tel: +49-40-2 26139-22 fax: +31 (0) 1 0 437-175 2 Technical Su pport : US &Canada 1-800-22ANTE C customersupp ort@antec.
デバイスAntec SOLO IIの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Antec SOLO IIをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAntec SOLO IIの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Antec SOLO IIの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Antec SOLO IIで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Antec SOLO IIを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAntec SOLO IIの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Antec SOLO IIに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAntec SOLO IIデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
