KitchenAidメーカーKHMS 105の使用説明書/サービス説明書
ページ先へ移動 of 20
INSTALLATION INSTRUCTIONS. ’ KitchenAid@ 30” BUlLT4N MICRO WAVE/HOOD MODEL: KHMS 105 MICRO WAVE-CONVECTION HOOD MODEL: KHMC 106 Read And Save These Installation instructions.
-. INTRODUCTION Please read all instructions thoroughly before installing Microwave/Hood System. TWO PEOPLE are required to in-iall this product. If a new electrical outlet is required, it should be connected by a qualified electrician before the MicrowaveB-lood -1 is installed.
MOUNTING SPACE Microwave/Hood System requires mounting space on a wall as shown below. I BACKSPLASH ,30” OR MORE FROM COOKING SURFACE t- 66” OR MORE FROM FLOOR J For removal of the Microwave/Hood .
. WALL CONSTRUCTION Microwave/Hood System should be mounted against and supported by a flat, vertical wall: If wall is not flat, use spacers to fill gaps. Mounting plate must be flat for proper installation. Wall construction should be a minimum of 2” x 4” wood studding and 3/S” or more thick dry wall or plaster/lath.
. ELECTRICAL SERViCE Visual check after unpacking. Remove all packing material from the oven cavity. Check the oven for any damage, such as misaligned door, damaged ,gaskets around door or dents inside the oven cavity or on the door.
HOOD EXHAUST DUCT Outside ventilation requires HOOD EXHAUST DUCT. Read the following carefully. EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3-x” x 10” rectangular duct. If round duct is required, a rectangular-to-round transition adaptor must be used.
‘TOOLS RECOMMENDED FOR INSTALLATION Phillips Screw -Driver Electric Drill 5/8”, 3/32” Drill Bit l-1/2” Wood Bit Pencil Measure Tape Saw to cut exhaust opening (if needed) Protective drop cloth for product and range. You may use part of carton for protectim.
PREPARATION OF PRODUCT / Figure 1 3. Remove and save two hexagonal Philiips head screws (inside grease filter openings) (Fig. 2). HEXAGONAL PHILLIPS HEAD SCREW FRONT / SIDE REMOVING MOUNTING PLATE 1. Use a portion of the carton or some other material to protect the outercase from being damaged.
LOWER HOOKS SLIDERS Figure 3 LEVERS 4. Pull out two levers to release sliders from hooks. This action will release mounting plate from back surface of outercase. Familiarize yourself with the operation of the mountrng levers so you will be aware of the proper pro- cedure for mounting the unit to the wall.
VENTILATION SYSTEM .: MICROWAVE/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THE FOLLOWING THREE (3) TYPES OF VENTILATION SYSTEMS. Select the type required for your installation. a. OUTSIDE VENTILATION: Vertical Exhaust b. OUTSIDE VENTILATION: Horizontal Exhaust c.
B. OUTSIDE VENTILATION: Horizontal Exhaust 1. Remove and save 9 screws. Remove rear stay (Fig. 5). 2. Withdraw hood fan unit carefully (Fig. 6). 3. Rotate hood fan unit ‘/4 turn (Fig.
4. Replace hood fan unit into oven unit with left corner side inserted into opening first, right corner next. Be careful -not to pinch the lead wire between the back plate and hood fan unit (Fig. 8). Figure 8 5. Replace the rear stay. First, attach rear stay to unit with 2 screws (Fig.
t. RECIRCULATING: Non-Vented, Ductless I. Remove and save 9 screws. Remove rear stay. (Fig. 5 pg. 11). 2. Withdraw hood fan unit. (Fig. 6 pg. 11). 3. Change lead wire holding position from left side wire retainer to right side wire retainer (Fig. 11).
PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES I’ CAUTION: THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO MOUNTING INSTRUCTIONS ON BOTH TEMPLATES. Read and follow mounting information on both Top Cabinet and Wall Templates. Templates are included in the printed matters packed witlithis oven.
-MOUNTING PLATE INSTALLATION 1. Separate toggle bolts from toggle nuts. 2. Insert one toggle bolt into each hole on the mounting plate (these holes correspond to holes A, B, C and D of the Wall Template) and put toggle nut onto the toggle bolt (Fig. 13).
PRODUCT INSTALLATION 1. Place Styrofoam packing blocks (2 pieces) on top surface of range/cooktop Figure 16 2. Place microwave/hood system on top of Styrofoam blocks as shown in Fig. 16. 3. Thread power supply cord through the hole at the bottom of top cabinet.
7. Check to be sure the unit is secure to the mounting plate at both upper and lower hooks when you remove your support. 8. Screw hexagonal Phillips head screws to levers (inside grease filter opening) (Fig. 18). Figure 18 9. Check that both levers (a) are securely fixed.
10. Use adjusting screws fc) and flat washers (d) for gaps between top cabinet and unit (Fig. 19). Id) Figure 19 11:Make a bundle of power supply cord, then fix it to cabinet using cord hook A short power supply cord is provided to reduce the risks resulting from contacting the cooking sur- face or from becoming tangled.
. CHECK LIST FOR INSTALLATION 1. Make sure unit has been installed according to instructions 2. Remove all packing material from the oven. 3. Plug in power cord. 4. Read Use and Care Manual. 5. Keep installation instructions for the local electrical inspector’s use.
km MS032 KitchenAid, Inc. St. Joseph, MI 49085 (f/74735.
デバイスKitchenAid KHMS 105の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
KitchenAid KHMS 105をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKitchenAid KHMS 105の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。KitchenAid KHMS 105の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。KitchenAid KHMS 105で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
KitchenAid KHMS 105を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKitchenAid KHMS 105の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、KitchenAid KHMS 105に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKitchenAid KHMS 105デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。