AOCメーカーe2051Snの使用説明書/サービス説明書
ページ先へ移動 of 59
1 www .aoc.com ®201 1 AOC. All Rights Reserved. LCD Monitor User Manual e 2 0 51 Sn.
2 Safety ............................................................................................................................... ......................................... 4 National C onventio ns ...........................................
3 Service ....................................................................................................................... ............................................. 55 W arranty S tatement for Europe ....................................
4 Safety National Conventions The following subsections desc ribe not ational conventions used in this doc ument. Notes, Cautions, and W arnings Throughout this guide, blocks of text ma y be accompanied by an icon and printed in bold t y pe or in italic type.
5 Power The monitor should be operat ed only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your hom e, consult your dealer or local power company . The monitor is equipped w ith a three-pronged grou nded plug, a plug with a third (grounding) pin.
6 Inst allation Do not place the monitor on a n unst able cart, stand, tripod, bracket, or table. If the monitor falls, it can inj ure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
7 Cleaning Clean the cabinet regularly w ith cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the pro duct cabinet. When cleaning, make sure no detergent is leaked into the product. The clea ning cloth should not be too rough as it will scratch the screen surface.
8 Other If the product is emitting a strange smell, sound or smoke, disconnect the po w er plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating ope nings are not blocked by a table or curt ain. Do not engage the LCD monitor in severe vib ration or high imp act conditions during operation.
9 Setup Content s in Box Not all signal cables (Analog, DVI, and HDMI cables) will be provided for all countries and regions. Ple ase check with the local dealer or AOC branch office for confirmation.
10 Setup S t and & Base Please setup or remove the base follo w ing the steps as below . Setup: Remove:.
11 Unit standing without base is available. (Caution: must put unit in flat surf ace. Any uneven or sloped surfa ce may result unit damaged or injur y to user .
12 Adjusting V iewing Angle For optimal viewing, it is recommended to look at the full face of the monitor , and then ad just the monitor's angle to your own preference. Hold the stand so you will not toppl e the moni tor when you change the monitor's angle.
13 Connecting the Monitor Cable Connections In Back of Monitor an d Computer: 1 2 D-SUB Power T o protect equipment, always turn off the PC and LCD monitor before connecting.
14 Adjusting Setting Optimal Resolution Windows Vist a For Window s Vist a: 1 Click ST ART . 2 Click CONTROL P ANEL. 3 Click Appearance and Personalization.
15 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1600 by 900..
16 Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y ..
17 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1600 by 900. Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1600 by 900.
18 Hotkeys Power Press the Power button to turn on/off the monitor . Menu/Enter Press to display the OSD or confirm the sel ection. Eco (DCR)/ - Press the Eco key continuously to select the Eco m ode of brightness an d DCR on when there is no OSD. (Eco mode hot key may not be available in all mode ls).
19 OSD Setting Basic and simple instruction on the control keys. 1. Press the MENU-button to activate the OSD w indow . 2. Press or to navigate through the functions. Once t he desired function is highlig hted, press the MENU-button to activate it. If there is a sub-menu, press or to navigate through the sub-menu functions.
20 Luminance 1 Press (Menu) to di splay menu. 2 Press or to select (Luminance), and press to enter . 3 Press or to select submenu, and press to enter .
21 4 Press or to adjust. 5 Press to exit . Brightness 0-100 Backlight Adju stment Contrast 0-100 Contra st from Digital-register. Eco mode Standard Standard Mode Tex t Text Mode Internet Internet Mode.
22 Image Setup 1 Press (Menu) to displ ay menu. 2 Press or to select (Image Setup), and press to enter . 3 Press or to select submenu, and press to enter .
23 4 Press or to adjust. 5 Press to exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Lin e noise. Phase 0-100 Adjust Picture Phas e to r educe Horizontal-Line noise Sharpness 0-100 Adjust picture sharpness H.Position 0-100 Adjust the hori zontal position of the picture.
24 Color Setup 1 Press (Menu) to displ ay menu. 2 Press or to select (Color Setup), and press to enter . 3 Press or to select submenu, and press to enter .
25 4 Press or to adjust. 5 Press to exit . Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM.
26 Picture Boost 1 Press (Menu) to displ ay menu. 2 Press or to select (Picture Boost), and press to enter . 3 Press or to select submenu, and press to enter .
27 4 Press or to adjust. 5 Press to exit . Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H.
28 OSD Setup 1 Press (Menu) to displ ay menu. 2 Press or to select (OSD Setup), and press to enter. 3 Press or to select submenu, and press to enter ..
29 4 Press or to adjust. 5 Press to exit . H.Position 0-100 Adjust the horizontal position of OSD V.Position 0-100 Adjust t he vertical position of OSD Timeout 5-120 Adjust the OSD Timeout Transparenc.
30 Extra 1 Press (Menu) to di splay menu. 2 Press or to select (Extra), and press to enter . 3 Press or to select submenu, and press to enter ..
31 4 Press or to adjust. 5 Press to exit . Input Select Analog Select Analog Signal Source as Input Auto Config yes or no Auto adjust the picture to default Off timer 0-24hrs Select DC off time Image .
32 Exit 1 Press (Menu) to displ ay menu. 2 Press or to select (Exit), and press to exit. Exit Exit the main OSD LED Indicator St atus LED Color Full Power Mode Blue Active-off Mode Orange.
33 Driver Monitor Driver Windows 7 1. S tart Windo w s® 7 2. Click on the 'St art' button and then click o n 'Control Panel'. 3. Click on the 'Display' icon.
34 4. Click on the “Change display settings” button. 5. Click the “ Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
35 7. Click the “Driver” tab. 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer " .
36 10. Click the “Have Disk” button. Click on the “Browse” button and n avigate to the following directory: X:Drivermodule name ( where X is the drive letter designator for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button.
37 Windows Vist a 1. Click "S tart" and "Control Pan el". T hen, do uble-click on "Appearance and Personaliz ation". 2. Click "Personalization" and then "Dis play Settings". 3. Click "Advanced Settings.
38 4. Click "Properties" in the "Monitor" t ab. If the "Properties" button is deactiva ted, it means th e configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue".
39 Windows XP 1. S tart Windo w s® XP . 2. Click on the 'S ta rt' button and then click on 'Control Panel'. 3. Select and click on the category ‘Appeara nce and Themes’ .
40 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your m onitor is properly configur ed. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
41 8. Select the 'Install from a list or specific location [ advanced]' radio button an d then c lick on the 'Next' button. 9. Select the 'Don't Search. I will choose the driv er to in stall' radio button. Then c lick on the 'Next' button.
42 Windows 2000 1. S tart Windo w s® 2000. 2. Click on the 'S ta rt' button, point to 'Se ttings', and then click on 'Control Panel' . 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
43 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor disp lay setting by using on screen menus instead of the OSD button on the monitor .
44 e-Saver Welcome to use AOC e-Saver monitor po w er management software ! The AOC e-Saver features Smart Shutdown functions for your monitors, all ows your monitor to timely shutdown when PC unit is at a ny status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
45 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window . Y ou only nee d to drag the window to a corresponding pane, when you want to access it.
46 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor . No images on the screen z Is the power cord connected properly? Check the power cord connection and po w er supply .
47 Monitor Is Stu ck In A cti v e Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in it s slot. Make sure the monitor's video cable is prop erly connected to the computer . Inspect the monitor's video cable and mak e sure no pin is bent.
48 S pecification General S pecification Panel Model name e2051 Sn Driving system TFT Color LCD Viewable Image Size 5 08.05 mm diagonal Pixel pitch 0.0 922 *RGB(H)mm x 0.2 766 (V)mm Video R, G , B Analog lnterface Separate Sy nc. H/V TTL Display Co lor 16.
49 Preset Display Modes VGA 640x480@60Hz 31.469 59.940 640x480@72Hz 37.861 72.809 640x480@75Hz 37.500 75.00 SVGA 800x600@56Hz 35.156 56.250 800x600@60Hz 37.879 60.
50 Pin Assignment s Pin Number 15-Pin Side of the Signal Cable Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 9 +5V 2 Video-Green 10 Ground 3 Video-Blue 1 1 N.
51 Plug and Play Plug & Play DDC2B Feature This monitor is equipped w ith VESA DDC2B capabilities according to the V ESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, dependi ng on the level of DDC used, communicate additional information about its display capabilities.
52 Regulation FCC Notice FCC Class B Radio Freq ue ncy Interference Statement W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to compl y with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
53 WEEE Declaration Disposal of W aste Equipment by Users in Pr ivate Hous ehold in the European Union. This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household wast e.
54 EPEA T Declaration EPEA T is a system to help purchasers in the public an d private sectors evaluate, compare and select des ktop computers, notebooks and monitors ba sed on their environmental attributes .
55 Service W arranty S t atement for Europe LIMITED THREE-YEAR W ARRANTY* AOC Color Monitors sold within Europe AOC International (Europe) GmbH w arrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of c onsumer purchase.
56 This limited warranty does not cover any of the product fi rmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for an y such modification or alteration.
57 W arranty St atement for North & South America (excluding Brazil) W ARRANTY ST A TEMENT for AOC Color Monitors Including those Sold w ithin North America as S pecified Envision Peripherals, Inc.
58 ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA TION TO A PERIOD OF THREE (3) YEA RS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
WARRANTY PERIOD COVERAGE AT NO CHARGE CUSTOMER CHARGES Within the first three months of purchase: Covered by EASE - New AOC monitor - Call tag dispatched and return freight charges via UPS - None* Bet.
デバイスAOC e2051Snの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
AOC e2051Snをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAOC e2051Snの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AOC e2051Snの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AOC e2051Snで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AOC e2051Snを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAOC e2051Snの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AOC e2051Snに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAOC e2051Snデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。