AOCメーカーE2276VW6の使用説明書/サービス説明書
ページ先へ移動 of 73
LCD Monitor User Man ual E2276VW6/E2276VWM6/E2476VW6/E2476VWM6 (LED Backlight) www .aoc.com ©2014 AOC.All Rights Reserved..
1 Safety ................................................................................................................................................................ 3 National Conventions ..........................................................
2 Pin Assignments ........................................................................................................................................ 59 Plug and Play ...............................................................................
3 Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
4 Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company . The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
5 Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
6 Cleaning Clean the cabinet regularly with cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
7 Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
8 Setup Contents in Box Monitor CD Manual Power Cable Monitor Base * * * * Analog Cable DVI Cable HDMI Cable MHL Cable * Not all signal cables (Analog, DVI, MHL and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch ofce for conrmation.
9 Setup Stand & Base Please setup or remove the base following the steps as below . Setup: Remove:.
10 Adjusting V iewing Angle For optimal viewing it is recommended to look at the full face of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle.
11 Connecting the Monitor Cable Connections In Back of Monitor and Computer: 3 2 1 5 4 2 1 E2276VW6/E2476VW6 E2276VWM6/E2476VWM6 1. AC port 2. Analog (D-Sub 15-Pin VGA cable) 3. DVI (E2276VW6/E2476VW6) 4. HDMI/MHL (E2276VWM6/E2476VWM6) 5. Earphone (E2276VWM6/E2476VWM6) T o protect equipment, always turn off the PC and LCD monitor before connecting.
12 W all Mounting Preparing to Install An Optional W all Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately . Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm.
13 AOC Anti-Blue Light Feature Description Studies have shown that just as ultra-violet rays can cause eye damage, blue light rays from LED displays can cause damage to different parts of the eye and af fect vision over time.
14 Adjusting Setting Optimal Resolution Windows 8 For Windows 8: 1. Right click and click All apps at the bottom-right of the screen. 2. Set the “View by” to “Category” .
15 4. Click DISPLA Y . 5. Set the resolution SLIDE-BAR to Optimal preset resolution. Windows 7 For Windows 7: 1. Click ST ART . 2. Click CONTROL P ANEL .
16 3. Click Appearance . 4. Click DISPLA Y . 5. Set the resolution SLIDE-BAR to Optimal preset resolution.
17 Windows V ista For Windows Vista: 1. Click ST ART . 2. Click CONTROL P ANEL . 3. Click Appearance and Personalization . 4. Click Personalization.
18 5. Click Display Settings . 6. Set the resolution SLIDE-BAR to Optimal preset resolution.
19 Windows XP For Windows XP: 1. Click ST ART . 2. Click SETTINGS . 3. Click CONTROL P ANEL . 4. Click Appearance and Themes . 5. Double click DISPLA Y .
20 6. Click SETTINGS . 7. Set the resolution SLIDE-BAR to Optimal preset resolution Windows ME/2000 For Windows ME/2000: 1. Click ST ART . 2. Click SETTINGS .
21 Hotkeys 12345 E2276VW6/E2476VW6 E2276VWM6/E2476VWM6 1 Clear vision /< 1 Clear vision /< 2 4:3 or wide /> 2 V olume / > or 4:3 / Wide / > 3 Power 3 Power 4 Source/Auto/Exit 4 Source/Auto/Exit 5 Menu/Enter 5 Menu/Enter Power Press the Power button to turn on/off the monitor .
22 Clear Vision 1. When there is no OSD, Press the “<” button to activate Clear Vision. 2. Use the “<” or “>” buttons to select between weak, medium, strong, or off settings.
23 Using “MHL(Mobile High-Denition Link)” “MHL” (Mobile High-Denition Link) This feature allows you to enjoy videos and photos(imported from a connected mobile device that supports MHL) on the screen of the product. ● T o use the MHL function, you need an MHL-certied mobile device.
24 OSD Setting Basic and simple instruction on the control keys. Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press the -button to activate the OSD window .
25 Luminance Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1.
26 Luminance Image Setup 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Color Setup Picture Boost OSD Setup Extra Exit Contrast 50 Medium Overdrive On DPS 4.
27 Image Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Color Setup Picture Boost Exit Extra Clock 50 50 50 50 50 Phase H.
28 Luminance OSD Setup Color Setup Picture Boost Exit Extra 50 50 50 50 Phase H.Position V .Position Sharpness Image Setup 50 Clock 4. Press < or > to adjust. Luminance OSD Setup Color Setup Picture Boost Exit Extra Clock 50 50 50 50 50 Phase H.
29 Color Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red Color T emp.
30 Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red 50 Green DCB Mode off 50 Blue DCB Demo off Color T emp. Warm 4. Press < or > to adjust. Luminance OSD Setup Color Setup Picture Boost Exit Extra Image Setup 50 Red Color T emp.
31 Picture Boost Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H.
32 Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H. position 50 Frame Size 50 V .position 50 Brightness Color Setup Bright Frame off 4. Press < or > to adjust. Luminance OSD Setup Picture Boost Exit Extra Image Setup 50 Contrast 50 H.
33 OSD Setup Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press (Menu) to display menu. Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 Timeout Language English Break Reminder H.
34 Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 T imeout Break Reminder H. position V .position 50 Color Setup Picture Boost off Language English 4. Press < or > to adjust. Luminance OSD Setup Exit Extra Image Setup 0 25 Transparence 10 Timeout Language English Break Reminder H.
35 Extra Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1.
36 Luminance Exit Extra Image Setup Color Setup Picture Boost OSD Setup Image Ratio DDC-CI Auto Config Yes Reset Off timer 00 wide Yes NO Resolution: 1920(H)x1080(V) H. Frequency: 67KHz V . Frequency: 60Hz Input Select DVI 4. Press < or > to adjust.
37 Exit Luminance Image Setup Color Setup Picture Boost OSD Setup Extra Exit 50 Brightness Standard Gamma Gamma 1 Off DCR Eco mode Medium Overdrive On DPS Contrast 50 1. Press (Menu) to display menu. Luminance Exit Image Setup Color Setup Picture Boost OSD Setup Extra 2.
38 LED Indicator Status LED Color Full Power Mode White Active-off Mode Orange.
39 Driver Monitor Driver Windows 8 1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen. 3. Click on the “Control panel” icon 4.
40 5. Click on the “Display” icon. 6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button..
41 8. Click the “Monitor” tab and then click the “Properties” button. 9. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver ... “ and then click the "Browse my computer for driver software" button.
42 1 1. Select "Let me pick from a list of device drivers on my computer" . 12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
43 Windows 7 1. Start Windows® 7 2. Click on the 'Start' button and then click on 'Control Panel' . 3. Click on the 'Display' icon.
44 5. Click the “Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button. 7. Click the “Driver” tab.
45 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver ... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device drivers on my computer" .
46 Windows V ista 1. Click "Start " and "Control Panel ". Then, double-click on "Appearance and Personalization" . 2. Click "Personalization" and then "Display Settings" . 3. Click "Advanced Settings.
47 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the conguration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the gure below , click "Continue" .
48 Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel '. 3. Select and click on the category ‘Appearance and Themes’ 4.
49 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly congured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
50 8. Select the 'Install from a list or specic location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
51 Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
52 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor .
53 e-Saver Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
54 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a dif ferent window . Y ou only need to drag the window to a corresponding pane, when you want to access it.
55 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor . No images on the screen • Is the power cord connected properly? Check the power cord connection and power supply .
56 Specication General Specication (21.5'') Panel Model name E2276VW6/E2276VWM6 Driving system TFT Color LCD Viewable Image Size 54.7 cm diagonal Pixel pitch 0.
57 General Specication (23.6'') Panel Model name E2476VW6/E2476VWM6 Driving system TFT Color LCD Viewable Image Size 59.8 cm diagonal Pixel pitch 0. 2715 mm(H) x 0. 2715 mm(V) Video (E2476VW6) R, G, B Analog lnterface & Digital Interface Video (E2476VWM6) R, G, B Analog lnterface & HDMI(MHL) interface Separate Sync.
58 Preset Display Modes ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHZ) VERTICAL FREQUENCY(Hz) VGA 640×480 @60Hz 31.469 59.94 640×480 @72Hz 37.861 72.809 640×480 @75Hz 37.5 75 MAC MODE VGA 640 × 480@67Hz 35 66.667 IBM-MODE DOS 720×400@70Hz 31.469 70.
59 Pin Assignments 15-Pin Color Display Signal Cable Pin Number Signal Name Pin Number Signal Name Pin Number Signal Name 1 Video-Red 6 GND-R 11 N.C. 2 Video-Green 7 GND-G 12 DDC-Serial data 3 Video-Blue 8 GND-B 13 H-sync 4 N.C. 9 +5V 14 V -sync 5 Detect Cable 10 Ground 15 DDC-Serial clock 24-Pin Color Display Signal Cable Pin No.
60 19-Pin Color Display Signal Cable Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2+ 9 TMDS Data 0- 17 DDC/CEC Ground 2 TMDS Data 2 Shield 10 TMDS Clock + 18 +5V Power 3 TMDS Data 2- 11 TMDS Clock Shield 19 Hot Plug Detect 4 TMDS Data 1+ 12 TMDS Clock - 5 TMDS Data 1Shield 13 CEC 6 TMDS Data 1- 14 Reserved (N.
61 Regulation FCC Notice FCC Class B Radio Frequency Interference Statement W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
62 WEEE Declaration Disposal of W aste Equipment by Users in Private Household in the European Union. This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.
63 EP A Energy Star ENERGY ST AR® is a U.S. registered mark. As an ENERGY ST AR® Partner , AOC International (Europe) BV and Envision Peripherals, Inc.
64 TCO DOCUMENT.
65 Service W arranty Statement for Europe LIMITED THREE-YEAR W ARRANTY* For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V . warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase.
66 All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards. If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor , shipping (if any) and applicable taxes.
67 W arranty Statement for Middle East and Africa (MEA) And The Commonwealth of Independent States (CIS) LIMITED ONE to THREE YEARS W ARRANTY* For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC International (Europe) B.
68 This limited warranty does not cover any of the product rmware or hardware that you or any third party have modied or altered; you bear the sole responsibility and liability for any such modications or alteration. All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
69 AOC International (Europe) B.V . Prins Bernhardplein 200 / 6th oor , Amsterdam, The Netherlands T el: +31 (0)20 504 6962 • Fax: +31 (0)20 5046933 AOC PIXEL POLICY ISO 9241-307 CLASS 1 July 25 th , 2013 AOC strives to deliver the highest quality products.
70 W arranty Statement for North & South America (excluding Brazil) W ARRANTY ST A TEMENT for AOC Color Monitors Including those Sold within North America as Specied Envision Peripherals, Inc.
71 ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA TION TO A PERIOD OF THREE (3) YEARS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
72 EASE PROGRAME E A S E P R O G R A M Only for AOC branded monitors sold within the continental United States. All AOC branded monitors are now covered by the EASE Program. If your monitor malfunctions at any time during the rst three months, AOC will provide a replacement monitor within 72 hours after you are approved for our program.
デバイスAOC E2276VW6の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
AOC E2276VW6をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAOC E2276VW6の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AOC E2276VW6の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AOC E2276VW6で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AOC E2276VW6を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAOC E2276VW6の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AOC E2276VW6に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAOC E2276VW6デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。