KodakメーカーGE1900の使用説明書/サービス説明書
ページ先へ移動 of 21
Prosilica Inc. www.prosilica.com tel: 604.875.8855 fax: 604.875.8856 © 2006 Prosili ca Inc. All righ ts reserved. prosili ca USER MA NUAL November 1, 2006 GE1900 GE1900C.
GE1900 User Manu al 70-0028A-A Prosilica Inc. ii Table of Cont ents Introduction ......................................................................................................................................1 Precautions ......................
GE1900 User Manu al 70-0028A-A Prosilica Inc. 1 Introduction The GE1900 series of cameras are sensitive, 30 frames per second, HDTV format, Gigabit Ethernet cameras based on the Kodak KAI-2093M CCD sensor . Precautions READ INSTALLATION G UIDE CAREFULLY.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 2 Specifications Sensor Type Kodak KAI-2093M (KAI- 2093CM for color) Sensor Shutter Type Progressive Interline Image Resolution 1920 x 1080 pixels Pixel Size 7.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 3 Supported Featu res Imaging Modes free-running, external trigger , fixed rate, software trig ger Fixed Rate Control 0.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 4 Mechanical 80.4* 57 13.9* 26 26 64 M3 3 MM DEEP 6 PLCS TYP 51.3 39.1 All dimensions are in mm. *Add 0.3mm for color cameras due to addition of IR blocking filter. Figure 1. GE SERIES m echanical dimensions.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 5 Connections 1 5 6 2 3 4 7 Figure 2. GE SERIES co nnection diagram..
GE1900 User Manu al 70-0028A-A Prosilica Inc. 6 Item 1: GIGABIT E THERNET PORT This port confor ms to the IEEE 802.3 1000BASE-T standard for Gigab it Et hernet over copper. It is recommended that CAT5E or CAT6 compat ible c abling and connect ors be used for be st performance.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 7 Sync Out 2 and Sync Out 3 These signals only function a s outputs and can be configur ed as follows: Exposing Corresponds to when camera is integrating light. Trigger Ready Indicates when the camera wi ll accept a trigger signal.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 8 Item 4: Mini-SMB Sync O ut 1 This Mini-SMB port o n the camera uses an Amphenol 903-406J-51R connector . A sui table mating cable connector is Amp 413 985-3 which can be used with RG174 coaxial cable. Contact Prosilica to purchase cabling .
GE1900 User Manu al 70-0028A-A Prosilica Inc. 9 Item 7: AUXILIARY POW ER PORT This port is required to provide power to the camera. This port provides thre aded captivation of the power cable i f required. The ca ptivated cable mating conn ector is the Switchcraft 760K.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 10 Cleaning the Sensor DO NOT CONTACT CLEAN SENSOR UNLESS ABS OLUTELY NECESSA RY. Identifying Debris Debris on the image sens or or optical components will a ppear as a darkened area or smudge o n the image that does not move as the camera is moved.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 11 Adjusting the C-mount LOCK ING RING C M OUNT RING Figure 4. Camera Fro nt View. THE C-MOUNT IS ADJUSTED AT T HE FACTORY AND SHO ULD NOT REQUIRE ADJUSTING. If for some reason, the C-mount requires adjustment, use the following method.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 12 Camera Instal lation Computer Interfac e The Pros ilica GE Series cameras will work with any Gigabit Ethernet netwo rk card; however Prosilica strongly recommends using Gigabit Ethernet components t hat support Jumbo Frames.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 13 Gigabit Ethernet Se tup for Windows o Install network car d in computer. o Boot the PC and cancel the “Found new Hardware Wizard” wi ndow that may appear whe n Windows detects the new car d. o Install the driver that came with the network card.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 14 o Select the Interne t Pr otocol ( TCP/IP) c heck box and then se lect Pr operties . See Figure 6. Network card TCP/IP address.. Select th e Use the following IP address and enter an IP address of 169. 254.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 15 Figure 7. Turn off Fir ewall. o Return to the Gige Local Properties window as in Fi gure 5. Select the Advanced tab as in Figure 7 and disable th e Firewall for this device.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 16 Installing GigE Vi ewer for Testing o The latest Viewer softwar e can be downloaded from http://www.prosi lica.com/support.htm . o Run the GigE Viewer Installer.exe. This will install the Prosilica Digital Camera drivers as well as the Prosilica GigE Vie wer application program.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 17 System Optimi zation o Open the Network Connections Dialog a s follows: From the Windows desktop select start , then select Control Pane l , then double click on the Network Connecti ons icon.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 18 Figure 10. Network card advanc ed settings. o Set Maximum Frame Si ze or Jumbo Frames to t he maximum possible value. A t ypical value is 9000 . If t he list con tains a pro perty called Receive Descriptors , then change t his value to its maximum val ue.
GE1900 User Manu al 70-0028A-A Prosilica Inc. 19 Trouble Shoot ing Check the Basics o Is power avail able? Check the status LED 1. If th e LED is off, the camera is not getting power. Verify the connecti ons and cabling. o Is the LED orange? This occurs if t he firmware i s corrupt becau se a firmware update was interrupted.
デバイスKodak GE1900の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kodak GE1900をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKodak GE1900の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kodak GE1900の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kodak GE1900で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kodak GE1900を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKodak GE1900の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kodak GE1900に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKodak GE1900デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。