AOCメーカーI2360PQの使用説明書/サービス説明書
ページ先へ移動 of 68
(LED Backlight) I2360PQ.
Safety ........................................................................................................................................................................ 4 National Conventions ....................................................
FCC Notice ...................................................................................................................................................... 57 W EEE Declarati on ...................................................................
Safe ty National Con ventions The following subsections describe notational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local pow er company . The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
Installation Do not place the mo nitor on an unstable cart, stand, tripod, bracket, or tabl e. If the mo nitor falls, it can injure a person and cause serious damage to thi s product. Use only a cart, stand, tripod, bracket, or ta ble recommended by the manufacturer or sold with this product.
Cleaning Clean the cabinet regularly with cloth. Y ou can use soft -detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. W hen cleani ng, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Other If the product is emitting a strange smell, sound or smoke, disconnect the pow er plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Setup Contents of the Box Not all signal cables (Analog , Au dio, DVI,USB 、 DP and HDM I cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Setup Stand & Base Please setup or remove the base following the steps as below . Setup: Remove: 10.
Adjusting Vie w ing Angle For optimal viewing it is recommended to look at the f ull face of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor w hen you change the monitor's angle.
Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1. 2. Power 3 HDMI (Optional) 4 . DVI (Optional) 5 . Analog (DB-15 VGA cable) 6. Line in (Optional) 7. Display port (Optional) Earphone out(Optional) T o protect equipment, always turn of f the PC and LCD monitor before connecting.
W all Mounti ng Preparing to Install An Optional Wall M ounting Ar m. This monitor can be attached to a wall mounting arm you purchase separately . Disconnect power before this procedure. Follow these steps: 1 Remove the base. 2 Follow the manufacturer's instructions to as semble the w all moun ting arm.
Adjusting Setting Optimal Resolution Windows 8 For Windows 8 : 1. Right click and click A ll apps at the bottom-right of the screen. 2. Set the “ View by ” to “ Category ”.
4. Click DISPLAY. 5. Set the resolution SLIDE-BAR to Optimal preset resolution 15.
Windows 7 For Windows 7: 1. 1. Click START. 2. 2. Click CONTROL P ANEL. 3. 3. Click APPEARANCE. 4. 4. Click DISPLAY. 16.
5. Set the resolution SLIDE-BAR to Optimal pres et resolution. 17.
Windows Vist a For Window s V ista: 1 Click ST ART . 2 Click CONTROL P ANEL. 3 Click Appearance and Personalization. 4 Click Personalization 18.
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1 920 by 1080 . 19.
Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y . 20.
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1 920 by 1080 . Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1 920 by 1080 .
Hotkeys 1 Source/Auto/Exit 2 Clear Vision/< 3 Volume / > 4 Menu/Enter 5 Power Power Press the Power button to turn o n/ off the monitor . V olume / > W hen ther e is no OSD,Press V olume butt.
21 Clear Vision 1. When there is no OSD, Press the “< ” button to activate Clear Vision. 2. Use the “<” or “>” buttons to select between weak, medium, strong, or off settings.
OSD Setting Basic and simple instruction on the control key s. 1) Press the MENU-button to activate the OSD window . 2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it .
Luminance 1 Press (Menu) to display menu. 2 Press < or > to select (Luminance), and press to enter . 3 Press < or > to select submenu, and press to enter.
Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Eco mode Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports Sports.
Image Setup 1 Press to display menu. 2 Press < or > to select (Image Setup), and press to enter . 3 Press < or > to select submenu, and p ress to enter . 4 Press < or > to adjust. 5 Press to exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.
Color Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Color Setup), and press to enter . 3 Press < or > to select submenu, and p ress to enter . 4 Press < or > to adjust. 5 Press to exit . Color setup. W arm Recall Warm Color Temperature from EEPROM .
Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press to enter . 3 Press < or > to select submenu, and press to enter . 4 Press < or > to adjust. 5 Press to exit . Frame Size 14 -100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H.
OSD Setup 1 Press (Menu) to display menu. 2Press < or > to select (OSD Setup), and press to enter . 3 Press < or > to select submenu, and p ress to enter . 4 Press < or > to adjust. 5 Press to exit . H. Position 0-100 Adjust the horizontal position of OSD.
Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press to enter . 3 Press < or > to select submenu, and press to enter . 4 Press < or > to adjust. 5 Press to exit . Input Select Auto / Analog / DVI / DP Select input s ig n al source.
Exit 1 Press (Menu) to di splay menu. 2 Press < or > to select (Exit), and press to enter . 3 Press to exit Exit Exit the main OSD LED Indicator Status LED Color Full Power Mode Green or Blue Ac.
Driver Monitor Driver Windows 8 1. Start Windows® 8 2. Right click and click A ll apps at the bottom-right of the screen. 3. Click on the “Control panel” icon 4.
5. Click on the “Display” icon. 6. Click on the “Change display settings” button. 7. Click the “ Advanced Settings” button . 8. Click the “Monitor” tab and then click the “Properties” button .
9. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver ... “ and then click the "Browse my comp uter for driver softw are" button. 11. Select "Let me pick from a list of device driv ers on my compute r" .
12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the follo wing directory: X:Drivermodule name ( where X is the driv e letter designat or for the CD-ROM drive). 13. Select the "xxx.inf" file and click the “Open” button.
Windows 7 1. Start Windows® 7 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Click on the 'Display' icon.
4. Click on the “Change display settings” button. 5. Click the “ Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
7. Click the “Driver” tab. 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Dri ver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer" .
10. Click the “Have Disk” button. Click on the “Brow se” button and navigate to the follo wing directory: X:Drivermodule name ( where X is the driv e letter designat or for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button.
Windows Vista 1. Click "Start" and "Control Panel". Then, do uble-click on "Appearance and Personalizatio n". 2. Click "Personalization" and then "Dis play Settings". 3. Click "Advanced Settings..
4. Click "Properties" in the "Monitor" t ab. If the "Properties" button is deactiv a ted, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue".
Windo w 1. Start 2. Click 3. Sele c 4. Click w s XP Windows® X on the 'Start' c t and click o n on the 'Displ a P button and th n the categor y a y' Item.
5. Sele c 6. Sele c - - Ple a 7. Click c t the 'Setting s c t 'Monitor' ta b If the 'Prope r If the 'Prope r a se follow th e on the 'Drive r s ' tab then cli c b r ties' button is r ties' button i s e steps below .
8. Sele c 9. Sele c 10. Click (CD- 11. Click 12. Sele c - 13. Click 14. Click c t the 'Install f c t the 'Don't S on the 'Have ROM Drive). on the 'Open c t your monit o If you can s e message, pl e on the 'Finis h on the 'OK' b rom a list or s earch.
Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Se ttings', and then click on 'Contro l Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
i-Menu Welcome to “i - Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor .
Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to complete software installation. Under each of the four PC status, you may choose from the pull-down menu the desired time (in minutes) for your monitor to automatically shutdow n.
installation software to install it. Screen+ Welcome to "Screen+" softw are by AOC, Sc reen+ software is a desktop screen splitting tool , it splits the desktop into different panes, each pan e displays a different w indow . Y ou on ly need to drag the window to a corresponding pane, when you want to access it.
No images on the screen Is the power cord connected properly? Check the power cord connection and power supply . Is the cable connected correctly? (Connected using the D-sub cable) Check the DB-15 cable connection. (Connected using the DVI cable) Check the DVI cable connection.
Missing one of the primary colors (RED, GREEN, or BLUE) Inspect the monitor's video cable and make sure that no pin is damaged. Make sure the monitor's video cable is properly connected to the computer . Screen image is not centered or sized properly Adjust H-Position and V -Positi on or press hot-key (AUTO).
Specification General Specifi cation Panel Model name I2360PQ Driving system TFT Color LCD Viewable Image Size 58.42 cm diagonal Pixel pitch 0.0883*RGB(H)mm x 0.265(V)mm Video R, G, B Analog lnterface & Digital Interface & DP lnterface Separate Sync.
Preset Displa y Modes ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHZ) VERTICAL FREQUENCY(Hz) VGA 640×480 @60Hz 31.469 59.940 VGA 640×480 @67Hz 35.000 66.667 VGA 640×480 @72Hz 37.861 72.809 VGA 640×480 @75Hz 37.500 75.000 Dos-mode 720×400 @70Hz 31.
Pin A s signmen ts Pin Number 15 -Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue s N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.
Pin No. Signal Name Pin No. Signal Name 1 ML_Lane 3 (n) 11 GND 2 GND 12 ML_Lane 0 (p) 3 ML_Lane 3 (p) 13 CONFIG1 4 ML_Lane 2 (n) 14 CONFIG2 5 GND 15 AUX_CH(p) 6 ML_Lane 2 (p) 16 GND 7 ML_Lane 1 (n) 17.
Plug and Pla y Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, c ommunicate additional information about its display capabilities.
Regulation FCC Notice FCC Class B Radio Frequency Interference State ment W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WEEE Declaration Disposal of Was te Equipment by Users in Private Household in the European Union. This symbol on the product or on its packaging indicates that this produc t must not be disposed of w ith your other household waste.
EP A Energy Star ENERGY ST AR® is a U.S. registe red mark. As an ENERGY ST AR® Partner , AOC International (Europe) BV and Envision Peripherals, Inc.
EPE A T Decl aration EPEA T is a system to help purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes.
Service W arranty Statement fo r Europe LIMITED THREE-YEAR W ARRANTY* For AOC LCD M onitors sold within Europe, AOC International (Europe) B.V . warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase.
This limited warranty does not cover any of the product firmware or hardware that you or an y third party have modified or altered; you bear the sole responsibility and liabil ity for any such modifications or alteration. All AOC LCD M onitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
Service W arranty Statement fo r Middle East and A fr ica (MEA) And The Commonwealt h of Independent St ates (CIS) LIMITED ONE to THREE YEA RS W ARRANTY* For AOC LCD M onitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC International (Europe) B.
Damages during transport due to improper packaging Improper installation or maintenance other then in accordanc e with AOC’s user manual Misuse Neglect Any cause other than ordin.
W arranty Statement for North & South A merica (excluding Brazil) WARR ANTY ST A TEMENT for AOC Color M onitors Including those Sold within North America as Specified Envision Peripherals, Inc.
MERCHANT A BILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA TION T O A PERIOD OF T HREE (3) YEARS FOR P ART S AND LABOR AND ONE (1) YEAR FOR CR T TUBE OR LCD P ANEL FROM T HE ORIGINAL DA TE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRES SED OR IMPLIED) APPL Y AFTER THIS PERIOD.
TCO DOCUMENT (FOR TCO CERTIFIED MODELS) 67.
68.
デバイスAOC I2360PQの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
AOC I2360PQをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAOC I2360PQの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。AOC I2360PQの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。AOC I2360PQで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
AOC I2360PQを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAOC I2360PQの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、AOC I2360PQに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAOC I2360PQデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。