Krell IndustriesメーカーKST100の使用説明書/サービス説明書
ページ先へ移動 of 16
.
A, INTRODUCTION Thank you for your purchase of the KRELL KST-100 poweramplifier. This amplifier represents the latest evolution ~n amplifier technology and incorporates many innovative design features. To obtain the best performance from. your KST-100, careful attention sfiould be paid to placement, installation and operation.
TABLE OF CONTENTS 4 UNPACKING AND ASSEMBLY 5 BASIC INSTALLATION AND OPERATION 6 INPUT AND OUTPUT CONNECTIONS 8 AMPLIFIER OPERATION 9 PROTECTION CIRCUITRY 10 MONAURAL CONVERSION OPERATION 11 REAR PANEL.
B. UNPACKING AND ASSEMBLY NOTE: Do to the weight of the KST-100 it is s.trongly advised that unpacking and placement is completed by at least two individuals. 1. Open the box on one end. 2. Fold back the flaps on all four sides of the box and carefully roll it over on to the exposed end.
C. BASIC INSTALLATION AND OPERATION 1. Place the KST-100 on a firm level surface away from excessive dirt or moisture. Ideally the amplifier should be placed as close to. the speakers as possible. It is always preferable to run long_ interconnect cables to the amplifier and keep speaker calSle length to.
D. INPUT AND OUTPUT CONNECTIONS CAUTION: When making connections to this component or any other, make sure the power amplifier is OFF and the preamplifier is in the MUTE or STANDBY mode. 1. Connect the speaker cables .to. the output terminals of the amplifier.
Thepin assignment for the XLR is: pin _1-= shield (ground) . p!n 2 = non-inverting ~nput (hot) p~n 3 - inverting input NOTE: The RCA center conductor for each channel is wiredjn, parallel with pin 2, the non-inv.erted input. Only one ot tlaese inputs should be connectecl to a preamplifier.
Eo AMPLIFIER OPERATION 1. Push the black breaker type switc.h on the front of the amplifier to turn it on. The LED in the switch will illumi- nate. When turning on the system, the a _m, plifier should always be last. Upon turn-on, the amplifier s outputs are not connectedto the speakers.
E PROTECTION CIRCUITRY There are no fuses in the KST-100. The amplifier is protected by a series of non-intrusive, opto-c_o, upled circuits that constantly evaluate the amplifier s operation. Appropriate protective action exists for DC conditions, short circuit, oscillation, AC power anomalies, high ground resistance and out-of:phase ground.
G. MONAURAL CONVERSION AND OPERATION The KST-100 can be easily cgnverted into a 400 watt monaural amplifier. To switcla the amplifier to mono follow these instructions. 1. Remove the topcover from the amplifier via 8 topcover screws. 2. Find the toggle switch located at the rear of the ampli- fier mounted on the circuitboard.
H. REAR PANEL DESCRIPTIONS INPUTS: Balanced via 3 pin XLR connector Single ended via RCA connector XLR PIN CONFIGURATION p!n 1 Shield (ground) p!n 2 Non-inverting or 0 degrees (hot) p~n 3 Inverting or.
I. OUESTIONS AND ANSWERS Q. Should I leave the KST-100 ON at all times? A. Althou.gh you could leave the KST-100 ON at all times without fear of damage to the amplifier, we recom- mend 30 minutes of warm-up_ before critical listening and switching the amplifier off when not in use.
Q. After the amplifier is playing for about one hour it becomes very hot. Is this normal? A. Yes. Due to the design of the KST-100 it will become quite warm when driven hard. If the amplifier should have a severe temperature inbalance between the left and fight channel, unplug the unit and call your authorized dealer or Krell.
¯ I. SPECIFICATIONS KST-100 GAIN 26dB, SIGNAL-TO-NOISE 102dB unweighted THD 1K at 8 ohms less than. 1% 20K at 8 ohms less than .3% INPUT IMPEDANCE 47,000 ohms(47K) INPUT SENSITIVITY 1.
K. WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the KST-100. The KST-100 has a limited warranty of .five years parts and labor.
45 CONNAIR RD ORANGE, CT 06477 SALES 203-799-9954 FAX 203-799-9796.
デバイスKrell Industries KST100の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Krell Industries KST100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKrell Industries KST100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Krell Industries KST100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Krell Industries KST100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Krell Industries KST100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKrell Industries KST100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Krell Industries KST100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKrell Industries KST100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
