Krell IndustriesメーカーMDA-300/500の使用説明書/サービス説明書
ページ先へ移動 of 15
.
A. INTRODUCTION Thank you for your purchase of the KRELL MDA-300 or MDA-500 power amplifiers. These amplifiers represent the latest evolution in amplifier technology and incorpo- rate many innovative design features. To obtain the best performance from your MDA-300/ 500s, careful attention should be paid to placement, installation and operation.
TABLE OF CONTENTS 4. UNPACKING AND ASSEMBLY BASIC INSTALLATION AND OPERATION INPUT AND OUTPUT CONNECTIONS 8. AMPLIFIER OPERATION 9. PROTECTION CIRCUITRY 10.
B. UNPACKING AND ASSEMBLY NOTE: Do to the extreme weight of the MDA-300 or MDA-500 it is strongly advised that unpacking and placement is completed by at least two individuals. 1. Open the box on one end. 2. Fold back the flaps on all four sides of the box and carefully roll it over on to the exposed end.
C. BASIC INSTALLATION AND OPERATION 1. Place the MDA-300/500, on a firm level surface away from excessive dirt or moisture. Ideally the amplifiers ’ should be placed as close, to the speakers as possible. ,It is always preferable torun long interconnect cables to tt~e amplifiers and keep speaker cable length t.
D. INPUT AND OUTPUT CONNECTIONS CAUTION: When making connections to this component or any other, make sure ttie power amplifiers are OFF and the preamplifier is in the MUTE or STANDBY mode. 1. Connect the speaker cables to the output terminals of each amplifier.
Thepin assignment for the XLR is: pin _1-= shiel-d (ground) p!n 2 = non-inverting input (hot) pin 3 = inverting input NOTE: The RCA center conductor for each channel is wired_in, parallel with pin 2, the non-inv, erted input. Only one ot these inputs Should be connectecl to a preamplifier.
E. AMPLIFIER OPERATION 1. Push the black button on the front of both amplifiers to turn them on. The blue LED on the front panels above each switch will illuminate.
E PROTECTION CIRCUITRY There are no fuses in the MDA-300/500s. The amplifiers are protected by a series of non-intrusive, opto-coupled circuits that constantly evaluate the amplifier’s operation.
H. REAR PANEL DESCRIPTIONS All descriptions are for each amplifier chassis INPUTS: Balanced via 3 pin XER connector Single ended via RCA connector XLR PIN CONFIGURATION p!n 1 Shield (ground) p.
I. QUESTIONS AND ANSWERS Q. Should I leave the MDA-300/500 on at all times? A. Although you could leave the MDA-300/500 on at all times without fear of damage to the amplifier, we recom- mend. 30 minutes of warm-up before critical listening and switching the amplifier off when not in use.
Q. After the amplifier is on for about one hour it be- comes very hot. Is this normal? A. Yes. Due to the high bias design of the MDA-300/500 it will become quite warm. After approximately 1 hour the amplifier will be at its optimum operating tempera- ture.
J, SPECIFICATIONS MDA-300 GAIN 26dB SIGNAL-TO-NOISE 106dB unweighted THD 1K at 8 ohms less than .2% 20K at 8 ohms less than .4% INPUT IMPEDANCE 47,000 ohms (47K) INPUT SENSITIVITY 2.
K. WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the MDA-300/ 500. The MDA-300/500 has a limited warranty of f~ve years parts and labor. Return freight is included in ~the warranty. The warranty period b.egins on thee date ot p_u_rchase and is activated with the return ot the enclosed Warran.
KRELL INDUSTRIES 35 HIGGINS DRIVE MILFORD CT 06460 SALES 203-874-3139 FAX 203-878-8373 COPYRIGHT 1992 KRELL INDUSTRIES (MDA9204).
デバイスKrell Industries MDA-300/500の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Krell Industries MDA-300/500をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKrell Industries MDA-300/500の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Krell Industries MDA-300/500の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Krell Industries MDA-300/500で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Krell Industries MDA-300/500を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKrell Industries MDA-300/500の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Krell Industries MDA-300/500に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKrell Industries MDA-300/500デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
