KyoceraメーカーEcoLAN 3000Eの使用説明書/サービス説明書
ページ先へ移動 of 20
Network Connectivity for Kyocera Printers Kyocera EcoLAN 3000E Quick Configuration Guide.
FCC Notice: This equipment complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Content s Introduction ......................................................................... 4 Using the CD ROM ............................................................. 4 Supported Kyocera Printer Models ................................... 5 EcoLAN 3000E Hardware Inst allation .
Introduction The EcoLAN 3000E is the next generation Kyocera internal network interface card allowing easy installation without removing the printer mainboard.
Supported Kyocera Printer Models The EcoLAN 3000E is compatible with the FS/LS-600, 680, 800, 1700+, 3700+, 5800C, 6700, 7000+, 9000 and any other Kyocera printer with the slide-in interface. The 3000E is compatible with the upper (hard disk) interface slot of an FS/LS-7000 with a Software version of 25.
6 NetW are 2.x & 3.x Configuration 1. Login as Supervisor and start PCONSOLE. 2. Define the Print Queue. ê If a Print Queue already exists that will be assigned to the 3000E, skip to step 3 ê Select Print Queue Information from the Available Options menu.
7 NetW are 4.x & 5.x Directory Services Configuration NetW are Directory Services (NDS) configuration is accomplished using two utilities; 1) NetW ares NW Admin is used to define the required D.
8 NetW are Directory Services Configuration continued... 3000E IPX Based Configuration IPX configuration is accomplished using the Management Access Program (MAP). 1. Install and Run MAP . ê Insert the CD included with the EcoLAN 3000E. ê In Windows 95, 98 or NT 4.
9 2. NetWare Configuration. ê Select Setup NetWare in the Protocols column. ê Enter the Print Server Name , Preferred NDS Context , and Print Server Password (if a password was defined) exactly as they were entered in NW Admin. Note: Entries are not case sensitive (except the sysadm pass- word).
10 Macintosh Configuration KPDL, Kyoceras PostScript compatible mode is required for Macintosh printing. KPDL is standard on many Kyocera printers, however , it is optional on the following models: FS-600, FS-680, FS-7000 and all LS (Japanese) models.
11 Inst alling the Driver and Selecting the Printer 1. The Macintosh LaserWriter Driver is installed from the CD provided with the printer . Insert the CD, open the Drivers folder , then the appropriate country folder , and double click on the FS-Series Installer program in the desired language.
12 Windows Peer to Peer Printing Configuration Peer to Peer printing is available for Windows 95, Windows 98 and Windows NT 4.0. What is Windows Peer to Peer Printing? The peer to peer printing software which is included with the EcoLAN 3000E allows Windows PCs to communicate directly with network attached printers.
13 IPX Printer Name: The IPX peer to peer printing software uses the NetW are Print Server Name to identify the 3000E. The default name is the serial number preceded by KYO, e.g., KYO_163495. If desired, this name can be changed to a more easily identifiable name with MAP .
Windows NT 4.0 Configuration There are several options for setting up printing in a Windows NT environment. u If a NetWare server is present, NetWare print services may be used by following the NetWare configuration instructions in this guide.
15 Configuring the Printer Driver for LPR Printing The printer driver should be installed from the CD which is shipped with the printer . Unfortunately , Windows does not make the Add LPR Port available to the Install Wizard on the CD. Therefore, the printer driver should be installed selecting a standard port such as LPT1.
16 DHCP Configuration (Dynamic Host Configuration Protocol) IMPORTANT: EcoLAN 3000E IP address assignment with DHCP will not work if the 3000E has an existing IP address and IP persistence is Permanent. DHCP provides a mechanism for delivering IP configuration parameters, including IP address, subnet mask, etc.
17 WINS Configuration (Windows Internet Naming Service) WINS provides a mechanism for mapping NetBIOS (Windows) names to IP ad- dresses. WINS enables defining a printing configuration which references the printer by its name rather than by its IP address.
18 UNIX Configuration UNIX printing utilizes a line printer daemon (lpd) to direct print jobs to the printer . The 3000E supports two modes of lpd printing, host-based lpd and printer-based lpd. With host-based lpd, the line printer daemon is run on one or more workstations (hosts) where print jobs are accepted and sent to the 3000E.
19 IP Address Setup with the Printer Front Panel Set the IP address and other 3000E parameters using the following procedure. Note: Setting the IP address with the front panel automatically sets IP Persistence to Permanent, that is, the IP address is maintained when the printer is turned off and on.
EcoLAN 3000E Quick Configuration Guide Re v . 1.0, June 1999 Part Number 8836056 Kyocera Corporation 2-14-9 T amagawadai, Set agaya W ard, T okyo 158 Japan Kyocera Communications Systems Co., Ltd. 2-14-9 T amagawadai, Set agaya W ard, T okyo 158 ww w .
デバイスKyocera EcoLAN 3000Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Kyocera EcoLAN 3000Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKyocera EcoLAN 3000Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kyocera EcoLAN 3000Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kyocera EcoLAN 3000Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kyocera EcoLAN 3000Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKyocera EcoLAN 3000Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kyocera EcoLAN 3000Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKyocera EcoLAN 3000Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。