KyoceraメーカーFS-1028MFP/DP/KL3の使用説明書/サービス説明書
ページ先へ移動 of 38
.
2 Introduction About this Guide This guide explains the following settin g method necessary to use this machine. Installation of the machine • Unpacking • Installing T oner Container • Loading P.
SETUP GUIDE 3 1 Prep arations Clearance Environment • T emperature: 10 to 32. 5 °C (50 to 90.5 °F) • Humidity: 15 to 80 %RH • Power Supply: 120 V AC, 60 Hz, 7.4 A / 220 to 240 V AC, 50/60 Hz, 3.8 A CAUTION: Be sure to provide enough space around machine.
Preparations 4 SETUP GUI DE 3 Slide the Shipping Lock to th e unlock position. IMPORTANT: When installing the Document Proces sor, refer to Installation Guide attached to the Document Processor. 4 Attach the Guide Case to the machine right as required.
Preparations SETUP GUIDE 5 4 Shake the toner co ntainer horizontally 5 or 6 times so that the toner inside becomes evenly distribut ed. 5 Remove the orange protective seal. 6 Align the knob on the left side of the container with the groove in the process unit and place the toner container into the process unit.
Preparations 6 SETUP GUI DE 9 Align the pins on both sides of the process unit with the guides inside the machine, and slide the process unit into the machine until it stops. 10 Close the front cover. Loading Paper 1 Carefully pull the casset te all the way out of the machine and re move the protec tive packing from inside the cassette.
Preparations SETUP GUIDE 7 5 Place the paper in the cassette, with side to be printed downward, so that the leading edge is aligned against the pape r stopper. IMPORTANT: Do not e xceed the upper limit of the casse tte. Other wise, it may ca use paper jams.
Preparations 8 SETUP GUI DE 2 Connect the machine to the PC or yo ur network device. When using the ne twork interface, remove the cap. These cables ar e sold separately. Available Standard Int erfaces: 3 Connect the power cord to the machin e and the other end into a power outlet.
Preparations SETUP GUIDE 9 Connecting Modular Cords (FS-1 128MFP only) 1 Turn the power switc h off (O). 2 Connect the modular cord with the attached ferrite core to the line jack (A) of the machine. Then, connect the modular cord to the telephone jac k (B) of the machin e.
Preparations 10 SETUP GUI DE.
Panel Setup 10 SETUP GUI DE 2P a n e l S e t u p Operation Panel Selecting Language Perform the following pr ocedure to select the language of the message display. Th e default message language is English . 1 Press [System Menu/ Counter] . The Sys. Menu/Count.
Panel Setup SETUP GUIDE 11 4 Press [OK] . The Time Zone scree n appears. 5 Press U or V to select the time zone that you are in. 6 Press [OK] . The time zone is set and t he Date Setting menu reappears. Summer Time Setting Perform the followin g procedure to turn the su mmer (daylight sa ving) time setting on and off.
Panel Setup 12 SETUP GUI DE IMPORTANT: Check with your networ k administrato r when selecting th e network setting. After all network related settings have been done, turn the machine Off and On again. TCP/IP (Enable/Disable TCP/IP) This selects the settings for TC P/IP.
Panel Setup SETUP GUIDE 13 DHCP 1 In the IPv4 Setting menu , press U or V to select DHCP . 2 Press [OK] . The DHCP screen appears. 3 Press U or V to select whether DHCP is enabled. 4 Press [OK] . The DHCP is set and the IPv4 Setting menu re appears. Bonjour 1 In the IPv4 Setting menu , press U or V to select Bonjour .
Panel Setup 14 SETUP GUI DE Default Gateway 1 In the IPv4 Setting menu , press U or V to select Default Gateway . 2 Press [OK] . The Default Gateway screen appears. 3 Use the arrow keys to set the default gateway. Press U and V to increase or decr ease, respectively, the value at the blinking cursor.
Panel Setup SETUP GUIDE 15 DHCPv6 1 In the IPv6 Setting menu , press U or V to select DHCPv6 . 2 Press [OK] . The DHCPv6 screen appears. 3 Press U or V to select whether DHCPv6 is enabled. 4 Press [OK] . The DHCPv6 is set and the IPv6 Setting menu r eappears.
Accessing COMMAND CENTER 16 SETUP GUI DE 3 Accessing COMMAND CENTER COMMAND CENTER refers to th e internal HTML web page that is installed in the machine from which you can veri fy the op erating status o f the machine and make settings related to security , network printing, e-mail tr ansmission and advanced networking.
Accessing COMMAND CENTER SETUP GUIDE 17 3 Click Submit . E-mail Settings The following procedure explains the method for atta ching scan data to e-mail fo r transmission . Scan to e- mail works with in the follo wing environm ents: • It must have a network en vironment in which this machine can connect to a mail server .
Accessing COMMAND CENTER 18 SETUP GUI DE 1 Click Advanced -> SMTP -> General . 2 Enter the correct settings in each field. The table be low provides a summary of the items displayed on the SMTP Protocol Settings page. Item Description SMTP Protocol Enables or disables SMTP protocol.
Accessing COMMAND CENTER SETUP GUIDE 19 3 Click Submit . Enabling SMB Function Stores the image data of scanned origin als as a file in a desired folder on your PC.
Accessing COMMAND CENTER 20 SETUP GUI DE 3 Click Submit . Enabling FTP Function The FTP transmission function converts th e data of origin als scanne d on this machine to the PDF, TIFF, J PEG, or XPS format and upload s it directly to an FTP server. Enable FTP parame ters in COMMAND CENTER.
Accessing COMMAND CENTER SETUP GUIDE 21 Editing Address Book This machine has an addre ss book function . When an e-mail address, the pa th of PC folder (SMB), FTP server's path, FAX, and i-F AX number are registered in the address book, it can tran smit directly from the operation pa nel.
Sharing PC Folder 22 SETUP GUI DE 4 Sharing PC Folder To use Scan to SMB (PC ) function , a "shared folder" mu st be set up with the destination computer to receive data. IMPORTANT: To use Scan to SM B (PC) function , the machine must be conn ected to a TCP/IP network.
Sharing PC Folder SETUP GUIDE 23 IMPORTANT: Log on to Windows with administrator privileges. NOTE: The following description is one exam ple of screenshot s of Windows XP . The det ails differ de pending on the type of operating system. 1 Create a folder named "scannerdata " on drive C.
Sharing PC Folder 24 SETUP GUI DE 8 Add the user name dis played in the Group or user names . Click Add , then click Locations . Select the compu ter to which the shared folder was created (Example: PC4050) and then click OK . 9 Enter the user name added as a local user into the text box and click OK .
Sharing PC Folder SETUP GUIDE 25 If the Computer Name t ab contains Full computer na me and Workgrou p All characters in the Full computer name text box corresp ond to the entry for Host Name. (Example: PC4050) Checking the Entry for Path Check the share name for the shared folde r to which data is sent.
Sharing PC Folder 26 SETUP GUI DE Checking the Entry for PathName You can use the following steps to check the dom ain name and user name tha t must be entered in Login User Na me. 1 Open the Command Prompt window . From the Star t menu, select All Programs , Accessories and then Command Prompt .
Sharing PC Folder 27 SETUP GUI DE.
Installing Printer Driver SETUP GUIDE 27 5 Inst alling Printer Driver Ensure the machine is plugged in and co nnected to the PC before installing the printer driver from the CD-ROM. Inst alling Printer Dr iver in Windows If you are connecting this machine to a Windows PC, follow the next steps to install the printer driver .
Installing Prin ter Driver 28 SETUP GUI DE 4 Click Install Software . The softwar e install wizard starts up. From this point, the procedure differs depending on your version of Windows and your connection method. Pro ceed to the correct procedure for your connection type.
Installing Printer Driver SETUP GUIDE 29 NOTE: If the Windows security window appears, click Install this drive r software anyway . 5 A message appears saying that the printe r has been installe d successfully. Click Finish to exit the printer installation wizard and return the CD-ROM main menu.
Installing Prin ter Driver 30 SETUP GUI DE 5 Double-click Kyocera OS X vx.x . 6 The printer driver installation pro gram starts up. 7 Choose Select Destination , Installation Type and then install the printer driver as directed by the ins tructions in the installation software.
Installing Printer Driver SETUP GUIDE 31 10 Click the IP icon for an IP connection or the AppleTalk icon for an AppleTalk conn ection and then enter the IP addr ess and printer name. 11 Select the installed printer driver and click Add . 12 Select the options available fo r the machine and click Continue .
Installing Prin ter Driver 32 SETUP GUI DE NOTE: Y ou can also add the machine to a PC when selecting Start of the Windows display , Control Panel and then Kyocera TW AIN . 2 Click Add . 3 Enter the machine name in the Name fie ld. 4 Click T next to the Model field and sele ct this machine from the list.
Installing Printer Driver SETUP GUIDE 33 8 Click OK. 9 The machine is r egistered to the PC and the machine nam e and model name ar e displayed in the Scanner List field.
Installing Prin ter Driver 34 SETUP GUI DE 3 Click the Settings t ab and select the Image Compression and the Compression Level . If user login administratio n is invalid, go to S tep 5. NOTE: When the machine’s IP address is unknown, contact Administrator .
.
First edition 2009.5 Printed in China 302H956020.
デバイスKyocera FS-1028MFP/DP/KL3の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Kyocera FS-1028MFP/DP/KL3をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはKyocera FS-1028MFP/DP/KL3の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Kyocera FS-1028MFP/DP/KL3の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Kyocera FS-1028MFP/DP/KL3で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Kyocera FS-1028MFP/DP/KL3を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はKyocera FS-1028MFP/DP/KL3の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Kyocera FS-1028MFP/DP/KL3に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちKyocera FS-1028MFP/DP/KL3デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
