La Crosse TechnologyメーカーWS-7014U-ITの使用説明書/サービス説明書
ページ先へ移動 of 19
WS-7014U-IT Wireless 915 MHz Radio-controlled Weather Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents/Additional Equipment 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery installation 5 Program Mode Program Sequence and Default Set.
3 INVENTORY OF CONTENTS 1. The Wireless Weather Station/ (Figure 1). 2. One remote temperature sensor with mounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive tape. 5. Instruction manual and warranty card.
4 signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in the Weather Station. However, due to the nature of the Earth’s Ionosphere, reception is very limited during daylight hours.
5 DETAILED SET-UP G UIDE I. BATTERY INSTA LLATION (When one temperature sensor is being used) 1. First, insert the batteries to the temperature sensor (see “ A . Remote Temperature Sensor ” below). 2. Within 2 minutes of powering up the sensor, insert the batteries to the Weather Station (see “ B.
6 • If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not successful the reception is tried for 45 se conds on 910MHz. This will also be done for re- synchronization.
7 Note: There are 8 LCD contrast levels to choose from—“Lcd 0” is the lightest, and “Lcd 7” is the darkest. 3. Press and release the IN button to select the level you desire. 4. Press and release the SET button to confirm and advance to the Time Zone setting.
8 “DST 0” indicates that the feature is off and the WWVB will not change times automatically. “DST 1” indica tes that the feature is on and the WWVB will change times automatically. Note: Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time, and should select “DST 0.
9 conducts a WWVB search every night between these hours, and overrides any manually set time. The WWVB tower icon (appearing in the TIME LCD) will flash when a signal-search is in progress and a signal is being received, and will remain steady when the signal has been received.
10 XI. SELECTING ° F OR ° C 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in the time LCD and the number setting will flash. 3. Press and release the SET button nine times. 4. Either ” ° F” or “ ° C” will flash in the time LCD.
11 FEAT URES OF THE WS-7014U-IT I. WEAT HER FORECAST The weather forecasting feature is estimated to be 75% accurate and is for the next 12 to 24 hours.
12 should be viewed as a generalization of the expected weather change (for example a “sunny” icon indicates the weather is expected to improve). The weather icons change when the unit detects a change in air pressure. The icons change in order, from “sunny” to “partly sunny” to “cloudy ” or the reverse.
13 2. Press the IN button again (once while “MIN” is still displayed, twice otherwise). “MAX” appears above the indoor temperature and the LCD will flash, indicating that the maximum temperature (along with the humidity measured at that time) and the time and date of occurrence are displayed.
14 LCD after 60 seconds, remove the batteri es and wait for at least 60 seconds before reinserting them. 4. The outdoor temperature from the first sensor (channel 1) should then be displayed on the Weather station.
15 reach the remote temperature sensor or Wi reless Weather Station. While the remote temperature sensor is weather proof, av oid submersion in water or snow.
16 The Wireless Weather Station comes with the table stand already mounted. If you w ish to use the table-stand all that is required is to place the Wireless Weather Station in an appropriate location. B. WALL MOUNTING 1) Remove the table-stand. To do this, pull down on the stand from the rear and rotate forward.
17 harder to compare different ranges with different curves. Under non-laboratory conditions, it is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENA NCE A ND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units.
18 determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.
19 support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrosse te chnology.com Questions? Instructions? Please visit: www.
デバイスLa Crosse Technology WS-7014U-ITの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
La Crosse Technology WS-7014U-ITをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLa Crosse Technology WS-7014U-ITの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。La Crosse Technology WS-7014U-ITの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。La Crosse Technology WS-7014U-ITで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
La Crosse Technology WS-7014U-ITを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLa Crosse Technology WS-7014U-ITの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、La Crosse Technology WS-7014U-ITに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLa Crosse Technology WS-7014U-ITデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
