La Crosse TechnologyメーカーWS-7215TWC-ITの使用説明書/サービス説明書
ページ先へ移動 of 25
WS-7215U-IT Wireless 915 MHz Radio-controlled Temperature Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipm ent 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery installation 5 Program Mode Program Sequence and Default S.
3 INVENTORY OF CONTENTS 1. The Wireless Temperature Station (Figure 1). 2. One remote tem perature sensor with m ounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive t ape. 5. Instruction m anual and warranty card.
4 2. Two fresh AA 1.5V batteries for the rem ote temperat ure sensor. 3. One, Philips screwdriver for mounting. ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards an d Technology—Time and Frequency Division) WWVB radio station is located in Ft.
5 obstruction (ro of, walls, floors, ceiling s, thick trees, etc.) will effectively cut sign al range in half. Example : A Wireless Temperat ure Station with a 330 feet range i s mounted on an interior wall, so t hat the signal has to pass through one interi or wall, one exterior wall, and across the 10 feet width of t he room between the 2 walls .
6 A. REMOTE TEMPERATURE SENSOR 1. Remove the m ounting bracket. The bracket snaps on and off easily. 2. Remove the battery cover, by sliding the cover down. 3. Observing the correct polarity install 2 AA batteries. The batteries will fit tigh tly (to avoid start-up problem s make sure they do not spring free).
7 successful (icon on) or not (icon off). On the other hand, the short blinking of the icon shows that a reception is being done now. • If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the frequency is changed to 920MHz and the l earning is tried another 45 seconds.
8 II. FUNCTION KEYS The function keys are located on the front of the un it directly below the LCD. III. SETTING THE LCD CONTRAST 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in the time LCD and the number setting will flash.
9 5. Press and release the IN button to select y our time zone. Note: When a time zone for the U.S. is selected the corresponding abbreviation will appear above the time (please see the table on the next page).
10 Note: Some locati ons (Arizona and parts of Indiana) do not follow Daylight Savi ng Time, and shoul d select “DST 0.” 6. Press and release the SET button to confirm and advance to the radio-controlled time on/off setting. VI. RADIO-CONTROLLED TIME ON/OFF SETTING 1.
11 Note: When in the 12-hour format “P .M.” will appear to the left of the hour in the tim e LCD between the hours of noon and midnight . 6. Press and release the SET button to confirm and advance to the time setting.
12 4. The time will flash in the time LCD. 5. Press and release the IN button to advance the hours. 6. Press and release the OUT button to advance the m inutes. 7. Press and release the SET button to confirm and advance t o the year setting. IX. SETTING THE YEAR, DAY AND MONTH Note: Reception of the WWVB signal will also set the date and day.
13 Note: This is an unused function of the Wireless Tem perature Station and should be disregarded. The setting has no bearing on t he operation. Please press and release the SET button to ad vance to se lect the temperature format. XI. SELECTING ° F OR ° C 1.
14 FEATURES OF THE WS-7215U-IT I. INDOOR TEMPERATURE AND HUMIDITY The current indoor tem perature (viewed on the left) and rel ative humi dity (viewed on the right) are displ ayed in the INDOOR LCD. II. OUTDOOR TEMPERATURE The temperature received from the rem ote temperature sensor is viewed in the OUTDOOR LCD.
15 III. MINIMUM AND MAXIMUM TEMPERATURE RECORDS The WS-7215U-IT keeps a record of the MINIMUM and MAXIMUM temperature, and t he time and date of t heir occurrence—for both the indoor and outdoor modes. A. VIEWING THE INDOOR TEMPERATURE RECORDS 1. Press the IN button once.
16 are displayed. The minimum records will display for 30 seconds before returning to the normal display m ode. 2. Press the OUT button again (o nce while “MIN” is still displayed, twice ot herwise).
17 humidity, and the time as 12:00 w ill be displayed. If they are no t shown in LCD after 60 seconds, rem ove the batteries and wait for at least 60 seconds before reinserting them . 4. The outdoor temperature from the first sensor (channel 1) shoul d then be displayed on the Wireless Tem perature Station.
18 once will display th e minimum tem perature, and the date and time the data was recorded. Pressing this butt on a second ti me (whil e “MIN” is still displayed, oth erwise press the butto n twice) will display the same data for the maximum recordings.
19 4) Screw mounting bracket onto the mounting surface. Ensure that the screws ar e flush with the bracket. 5) Insert the remote temperatur e sensor into the bracket. B. MOUNTING WITH ADHESIVE TAPE 1) With a nonabrasive solution, clean and dry the back of the mounting bracket and the mounting surface to ensure a secure hold.
20 B. WALL MOUNTING 1) Remove the table-st and. To do this, pull down on the stand from the rear and rotate forward. 2) Fix a screw (not included) into the desired wall, leaving approximat ely 3/16 of an inch (5m m) extended from the wall. 3) Place the Wireless Temperat ure Station onto the screw using the hanging hole on the backside.
21 Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactur ed to be accurate to within 1 degree plus or minus and under norm al conditions, so two sensors could be as much as 2 degrees different.
22 measuring range: temperature is OL.F; display “- -“ if < 1% and “99%” if > 99%) Indoor Temperature checking interval: Every 10 seconds. Indoor Humidit y checking interval: Every 1 minut e. Outdoor Temperature checking interval (Remote Temperature Sensor): Every 4 seconds.
23 Technology, Ltd will pay all expenses for la bor and materials for all repairs covered by this warranty. If necessary repairs ar e not covered by t his warranty, or if a product is examined which is not in need or repair, you will be charged for the repairs or examinati on.
24 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (informat ion on other products) web: www.lacrossetechnology.com Questions ? Instructions? Please visit: www.lacrossetechnology.
25 F CC ID: OMOTX29U (sensor) RF Exposure mobile: The internal / external antenn as used for this mobile sensor must prov ide a separation distance of at least 20 cm (8 inches) from all persons and must not be co- located or operating in conjuncti on with any other antenna or sensor.
デバイスLa Crosse Technology WS-7215TWC-ITの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
La Crosse Technology WS-7215TWC-ITをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLa Crosse Technology WS-7215TWC-ITの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。La Crosse Technology WS-7215TWC-ITの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。La Crosse Technology WS-7215TWC-ITで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
La Crosse Technology WS-7215TWC-ITを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLa Crosse Technology WS-7215TWC-ITの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、La Crosse Technology WS-7215TWC-ITに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLa Crosse Technology WS-7215TWC-ITデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
