La Crosse TechnologyメーカーWS2813UITの使用説明書/サービス説明書
ページ先へ移動 of 31
WS‐2813U‐IT WirelessProfessional WeatherCenter OperationsManual Revision: 5 .
Page | 2 TABLE OF CONTENTS TABLE OF CONTENTS……………………………… ……………………………… …….……………...2 INTRODUCTION……………………… ………………………………………… …………….
Page | 3 The following Weather Alarms can be adjusted in ALARM set mode… ………..…20 Default Weather Alarm values…………………………………………… ………….
Page | 4 ongratulations on purchasing this state ‐ of ‐ the ‐ art weather station. Featuring time, date, weather forecast, w.
Page | 5 INVENTORY OF CONTENTS Carefully open the package and check that the following contents are complete: Wind .
Page | 6 FEATURES: WIRELESS DISPLAY Time display in 12/24 hour time format Automatic time and date (PC tim.
Page | 7 100% solar ‐ powered with built ‐ in rechargeable alkaline power cell (not replaceable).
Page | 8 5. Setup troubleshooting: If the sensor data fails to display for any of the outdoor sensors within 10.
Page | 9 or the sensors closer and wait a few minutes to see if the wireless icons display again.
Page | 10 Position the display station to receive data from the thermo ‐ hygro sensor and send data to the USBTR.
Page | 11 Stop the weather alarm when ringing MIN/MAX KEY Press to display minimum and maximum record s of .
Page | 12 MANUAL SETTINGS: Press and hold the SET key for 3 seconds to enter the SET mode.
Page | 13 4. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to set the minute. 5. Press the SET key to confirm and to enter the 12/24 ‐ HOUR TIME DISPLAY SETTING .
Page | 14 1. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to toggle between the unit “mph”, “km/h”, "bft", "knots" or “m/s” 2.
Page | 15 .06, .09, or .12 inHg (2, 3 or 4 hPa). Select lower values (.06) for high humidity areas like the coastline. Select high numbers (.
Page | 16 FACTORY RESET PROCEDURE WARNING: Performing a factory reset will erase all MIN/MAX values and weather .
Page | 17 The Weather alarms can be set when certain weather conditions are met according to the requirements.
Page | 18 PRESSURE ALARMS 1. In the normal display mode, press the ALARM key once. The high ‐ pressure alarm display will be shown. 2. Press and hold the SET key for about 2 seconds.
Page | 19 2. Press and hold the SET key for about 2 seconds. The humidity digit will flash. 3. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to set the high indoor humidity alarm value.
Page | 20 5. Press the SET key to switch the alarm on or off. The ((( ))) icon indicates the alarm is switched on. 6. Press the ALARM key once.
Page | 21 24 HOUR RAINFALL ALARM 1. The 24 ‐ hour rainfall alarm display will be shown. 2. Press and hold the SET key for about 2 seconds. The 24 ‐ hour rainfall digit will flash.
Page | 22 Every time a new average pressure value has been obtained (once per minute), this value is compared with an internal reference value.
Page | 23 last noticeable change in the weather was when it was sunny (the sun icon only).
Page | 24 Press the SET key to toggle between Mode1 and Mode 2 of the display.
Page | 25 TOTAL RAINFA LL AMOUNT The total rainfall measurement is displayed in the unit of mm or inch. It shows the total rainfall accumulated since last reset of the total rainfall amount.
Page | 26 (“OF.L” displayed if outside this range) INDOOR HUMIDITY 1% to 99% with 1% resolution (“ .
Page | 27 RAINFALL 0" to 393.7" with 0.01 inch resolution 0 to 9999 mm with 0.1 mm resolution (displays "OF.L" when > 393.
Page | 28 RAIN SENSOR 2 x AA size batteries (IEC LR6, 1.5V) WIND SENSOR Solar powered BATTERY LIFE Approxi.
Page | 29 manufacturer. FCC STATEMENT Statement according to FCC part 15.19: This device complies with part 15 of the FCC rules.
Page | 30 WARRANTY INFORMATIO N La Crosse Technology, Ltd provides a 1 ‐ year limited warranty on this product against manufacturing defects in materials and workmanship.
Page | 31 La Crosse Technology, Ltd 2817 Losey Blvd. S. La Crosse, WI 54601 Customer Support: www.lacrossetechnology.com/support For more information: www.
デバイスLa Crosse Technology WS2813UITの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
La Crosse Technology WS2813UITをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLa Crosse Technology WS2813UITの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。La Crosse Technology WS2813UITの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。La Crosse Technology WS2813UITで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
La Crosse Technology WS2813UITを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLa Crosse Technology WS2813UITの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、La Crosse Technology WS2813UITに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLa Crosse Technology WS2813UITデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
