LanzarメーカーOPTIDRIVE OPTIX-10OPTIX-10の使用説明書/サービス説明書
ページ先へ移動 of 18
www .lanzar .com 10-Channel Active Electronic Crossover Network with Subwoofer Level Control user’s manual OptiX -1 0 OptiX -1 0.
Congratulations on your purchase of a new Lanzar Opti signal processor . Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting 2 3 4-6 7-11 12-13 14 15 table of contents.
10 Crossover Channels Blue Light Illumination 4 Channel Inputs Signal Pass-through for Additional Processors Remote Bass Level Control High Channels: Separate Front and Rear Frequency and Gain Control.
3 Precautions T o prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly . Reinstate all car parts that were removed.
4 featur es and specifications.
5 featur es and specifications 1. F/R INPUT SWITCH 2. FRONT & REAR CHANNEL MID CUT Q SELECTORS 3. FRONT & REAR CHANNEL MID CUT CONTROLS 4. Front & Rear Channel High-Pass Phase Inverters 5. Front Frequency & Gain Controls 6. Rear Frequency & Gain Controls 7.
6 featur es and specifications Crossover Frequencies -Front High-Pass -Front Mid High-Pass -Front Mid Low-Pass -Rear High-Pass -Rear Mid High-Pass -Rear Mid Low-Pass Crossover Slope Rate Subwoofer Boost Boost Frequency Mid Cut Mid Cut Q: Distortion Frequency Response Signal-to-Noise Ratio (A) Separation Power Source Dimensions 1.
7 System wiring 2-CHANNEL 3 WA Y SYSTEM REAR CHANNEL Speakers FRONT CHANNEL Speakers Head unit (Stereo, DVD Player , T ape Deck, etc.) TO REAR OUTPUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT BA T.
8 System wiring 2-CHANNEL MUL TIPLE CROSSOVER SYSTEM TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) SUBWOOFER Speakers REAR MID-WOOFER Speakers TO FRONT MID OUT TO REA.
9 TO SUB OUTPUT TWEETER Speakers SUBWOOFER Speakers TO FRONT MID OUT TO REAR HIGH OUT TO FRONT HIGH OUT GROUND BA TTERY MID-WOOFER Speakers WOOFER Speakers UPPER MIDRANGE Speakers (to REMOTE OUTPUT fr.
10 System wiring BA TTERY TO FRONT HIGH OUT 4 CHANNEL 4 WA Y SYSTEM TO REAR MID OUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT GROUND SUBWOOFER Speakers FRONT TWEETER Speakers REAR MID-WOOFER Speak.
11 System wiring 6-CHANNEL 5-WA Y SYSTEM FRONT TWEETER Speakers TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) to REMOTE OUTPUT from HEAD UNIT SUBWOOFER Speakers FRONT.
12 Mounting and installation Y our new Opti Series crossover comes complete with all required mounting hardware. Please read the Installation Precautions section below before installing your Lanzar Op.
13 Mounting and installation • Solder -less connectors or soldering gun with heat shrink tubing 1. Find a suitable location in the vehicle to mount the processor . The X-10 is a trunk mount unit and it should be installed in close proximity to your amplifier system on the amp rack.
NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. Start the engine. 2. T urn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
1. There is an audible distortion at a low volume level. PROBLEM POSSIBLE CAUSE • Output levels NOT set correctly . • Crossover frequencies NOT set correctly . • Check for shorts on the speaker leads. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running.
All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Signal Processor .
デバイスLanzar OPTIDRIVE OPTIX-10OPTIX-10の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lanzar OPTIDRIVE OPTIX-10OPTIX-10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLanzar OPTIDRIVE OPTIX-10OPTIX-10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lanzar OPTIDRIVE OPTIX-10OPTIX-10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lanzar OPTIDRIVE OPTIX-10OPTIX-10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lanzar OPTIDRIVE OPTIX-10OPTIX-10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLanzar OPTIDRIVE OPTIX-10OPTIX-10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lanzar OPTIDRIVE OPTIX-10OPTIX-10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLanzar OPTIDRIVE OPTIX-10OPTIX-10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
