Lenoxx ElectronicsメーカーCDR-1902の使用説明書/サービス説明書
ページ先へ移動 of 17
IB-CDR1902(T A)-WM-E-090902 CD PLA YER DUAL ALARM DIGIT AL CLOCK RADIO OPERA TING INSTRUCTIONS DUAL ALARMS - PERFECT FOR WEEKDA YS & WEEKENDS PLA YS MUSIC COMP ACT DISCS FULL Y PROGRAM.
IB-CDR1902(T A)-WM-E-090902 TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH AN EXTENSION CORD, RECEPT ACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL Y INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IB-CDR1902(T A)-WM-E-090902 ADDITIONAL SAFETY INSTRUCTIONS 1 . Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 2 . Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling.
IB-CDR1902(T A)-WM-E-090902 1. Setting the Clock 1 Connect the AC power cord into a live wall outlet. 3 Hold the TIME button down, and press the MINUTE button until the right minute time shows in the display . Hold the TIME button down, and press the HOUR button, until the right hour time shows in the display .
IB-CDR1902(T A)-WM-E-090902 2. Playing a CD 1 Press the POWER button to turn on the power , make sure the POWER lamp is on. Slide the FUNCTION switch to CD position. 3 Close the CD DOOR by pushing it down at the right corner . The display will show the total track number of the disc for 5 seconds, then go back to clock time display .
IB-CDR1902(T A)-WM-E-090902 Use these buttons for additional operations T o Press or Adjust Adjust the volume V olume Control Stop playback Pause playback CD track number will flash during pause.
IB-CDR1902(T A)-WM-E-090902 4. Playing CD tracks repeatedly (Repeat Play) T o repeat Press (during play) a single track (song) Press the REPEA T button once all the tracks (all songs) Press the REPEA T button twice 1. Press the POWER button to turn on the power and slide the FUNCTION switch to CD position.
IB-CDR1902(T A)-WM-E-090902 5. Playing CD in programmed order T o cancel Programmed Play Press the STOP button to stop programmed play . Press the STOP button again after pressing the PROGRAM button or press the CD DOOR OPEN button to open the CD door , and the PROGRAM lamp goes off.
IB-CDR1902(T A)-WM-E-090902 6. Listening to the radio Connect the supplied AC power cord (see Setting the Clock ). Press the POWER button to ON and slide the FUNCTION switch to RADIO position. 1 2 3 Slide the BAND switch to the proper band position that you want.
IB-CDR1902(T A)-WM-E-090902 T o improve broadcast reception FM ANTENNA Fully stretch out the FM ANTENNA for better FM reception. Reorient the player itself for better AM reception.
IB-CDR1902(T A)-WM-E-090902 8. Setting the Alarm Time This set has dual alarms. Y ou may set ALARM 1 to wake you at a certain time, or ALARM 2 to wake you at a different time, or ALARM 1+2 - both alarms will sound at the times you set.
IB-CDR1902(T A)-WM-E-090902 9. W aking up to alarm or music 2. W aking up to CD 3. W aking up to radio 2 . Set the FUNCTION switch to CD position. 3. Make sure there is a CD disc loaded in the compartment and POWER lamp is off. 1 . Refer to Listen to the radio for radio operation instructions.
IB-CDR1902(T A)-WM-E-090902 10. Snooze and Sleep functions 1. T o sleep extra 6 minutes 1. Follow steps 1-4 of Playing a CD on Page 4 to start the CD play . 2. Press the SLEEP button, the display will show two dashes --, and the SLEEP lamp flashes in the display .
IB-CDR1902(T A)-WM-E-090902 Precautions On safety As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing.
IB-CDR1902(T A)-WM-E-090902 Precautions (continued) Notes on CDs Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. Do not use solvents such as benzene, thinner , commercially available cleaners or anti-static spray intended for vinyl LPs.
IB-CDR1902(T A)-WM-E-090902 T rouble Shooting Problem Remedy The power is not on. Connect the AC power cord to a wall outlet securely . Make sure that outlet has power . There is no sound. Make sure the FUNCTION switch is at the right position as you want.
IB-CDR1902(T A)-WM-E-090902 Specification GENERAL DESCRIPTION Power source: AC 120V , 60Hz 10Watts DC 9V (optional - for clock backup) Speakers: 3 8 ohm Output power: 1.
デバイスLenoxx Electronics CDR-1902の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lenoxx Electronics CDR-1902をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLenoxx Electronics CDR-1902の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lenoxx Electronics CDR-1902の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lenoxx Electronics CDR-1902で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lenoxx Electronics CDR-1902を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLenoxx Electronics CDR-1902の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lenoxx Electronics CDR-1902に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLenoxx Electronics CDR-1902デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。