APCメーカーUTS6Hの使用説明書/サービス説明書
ページ先へ移動 of 30
Site Prep aration and Inst allation Guide Universal T ransfer Switch UTS6 UTS6H UTS6BI UTS10BI UTS10B I.
1 Site Preparation & Installation Guide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Introduction About this product The American Power Conversion ® (APC ® ) Universal T ransfer Switch (UTS) is a fully aut omatic trans f er switch for use in optional standby sy stems in homes or small bu sinesses.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 2 Unp ack and Inspect Inspect the UTS upon receipt. Notify the carrier and deal er if there is damage. The packaging is recyclable; save it fo r reuse or dispose of it properly .
3 Site Preparation & Installation Guide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Specifications UTS Specifications UTS6/UTS6H UTS6BI UTS10BI Electrical Input - Utility Input line Circu.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 4 UTS Specifications UTS6/UTS6H UTS6BI UTS10BI Output Nominal voltage 120 V circuits 120 V six total 120 V.
5 Site Preparation & Installation Guide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI UTS Configurable Features Featur e Description Uninterruptible Power Supply • provides UPS backup for.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 6 Site Planning and Prep aration Select a location Select a suitable location that meets the environmental specif ications and safety requirements of the UTS.
7 Site Preparation & Installation Guide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Generator Load Balance Follow these steps to ensure lo ad balance for the generator . UTS6/UTS6BI/UTS10BI models only 1. Determine the total power rating required if all connected loads were to run conti nuously and simultaneously .
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 8 Surface mount inst allation 1. Hang the UTS on a nail using the mounting ey elet located on the rear of the unit. 2. Locate two 16 inch on center wall studs within one fo ot of the building circuit break er panel.
9 Site Preparation & Installation Guide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI UTS circuit s Note: UTS6/U TS6H - Utilizing all of the UTS circuits is not necessary . However , Circuits 5 and 6 must be connected to the building circ uit panel and must receive power for the UTS to function.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 10 240 V circuit wiring Consult the UTS W iring Plan table in the Quick Install Guide that was filled in previously . The UTS6 and UTS6H p rovide 120 V circuits only .
11 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Wiring schematics UTS6.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 12 Wiring schematics UTS6H.
13 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Wiring schematics UTS6BI.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 14 Wiring schematics UTS10BI.
15 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI UTS Controls and Indicators The UTS controls and indicators ar e located on the front of the UTS.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 16 UTS Power Connectors The power connectors are locat ed on the front of the UTS. Connect Power to the UTS V erify circuit connections 1. Reconnect power to the circuit breaker pane l and switch ON all of the circuit breake rs.
17 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Initial Setup After several initializing LCD screens appear and the Utility Source LED illuminates, t.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 18 Backup2 Source T ype The factory default setting is UPS . The backup2 power source inlet, located on the front of the UTS is labeled UPS Inlet as a UPS is the pref erred BACKUP2 power source.
19 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI System St atus V erification The UTS system status and the status of up to three power sources can be viewed by pressing the System S tatus but ton located on the front of the UTS.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 20 Connect UTS to Backup Power So urces UTS10BI Generator W ARNING: Home generator backup systems should be installed by a licensed electrician. L ocate the generator outside a buildi ng and at le ast 10 f eet away f rom buildings, windows, and d oors.
21 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI UPS The UTS is equipped with a standard IEC 320, 120 V inlet specifically intended for use with a UPS. Use the power cord supplied in the accessories kit to connect the UPS to the UTS.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 22 T r oubleshooting Use this chart to solve minor UTS problems.
23 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Problem and Possible Cause Solution Prob lem: UTS configuration err ors are found Cause: Initial UTS configuration is found to be incorrect. • Reset the UTS to the factory defaul ts and be gin the setup process agai n.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 24 Loa d P ow e r Wat t s or Am ps UTS W iring Plan L oad V olt age UTS Circuits Ev en Odd Not es Even Cir.
25 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI Circuit Assignment s The t ables on this page a nd the previous p age are intended to be filled in and t aped to the inside cover of the building circ uit breaker p anel enclosure.
Site Preparation & Installation Guide Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI 26 Service If the unit requires service do not return it to the dealer . Follow these steps: 1. Review the problems di scussed in T roubleshooting to eliminat e common problem s.
27 Site Preparation & Installation Gu ide Universa l Transfer Switch UTS6 UTS6H UTS6BI UTS10BI T wo-Y ear W arranty The limited warranty provided by Amer ican Power Conversion (APC®) in this stat.
.
7/2008 990-2992B.
デバイスAPC UTS6Hの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
APC UTS6Hをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはAPC UTS6Hの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。APC UTS6Hの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。APC UTS6Hで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
APC UTS6Hを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はAPC UTS6Hの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、APC UTS6Hに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちAPC UTS6Hデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。