LGメーカーE1911S-BNの使用説明書/サービス説明書
ページ先へ移動 of 34
www .lg.com O WNER’S MANU AL L CD MONIT OR L CD MONIT OR MODEL E 1911T E1911S E2211T E2211S E2 4 11T P l ea s e re a d th i s ma n u a l ca r e fu l l y b e for e op e r a t i n g yo u r se t a n d re tain it f or futur e ref erenc e.
1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching.
4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.
Connecting the Display 5 Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture.
6 Connecting the Display . . Disassembling the stand 1. Put a cushion or soft cloth on aflat surface. 3. Change your lock on the product as it follows and turn it in the arrow direction.
7 Connecting the Display 4. Pull out the Stand to remove. 5. Pushing the PUSH button, Take the stand body from hinge body. Good Position Bad Position Warning: You can hurt your finger.
8 Connecting the Display Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below . 1. Adjust the position of the panel in various ways for maximum comfort.
9 Connecting the Display E191 1T/E221 1T/E241 1T NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
10 Connecting the Display E191 1S/E221 1S NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
11 Connecting the Display Using the cable holder (This feature is not available in all models.) Cable holder Cable holder E1911T E1911S.
12 Control Panel Functions Front Panel Controls E191 1T/E221 1T/E241 1T E191 1S/E221 1S MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds.
13 Control Panel Functions AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. ( Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).
14 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.
15 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : D-SUB(Analog signal) input : DVI-D(Digital signal) .
16 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub- menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
17 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. Change the input image signal ratio to original. WIDE ORIGINAL Switch to full screen mode according to input image signal. * This function works only if input resolution is lower than monitor ratio (16:9).
18 On Screen Display(OSD) Selection and Adjustment Main menu Description To choose the language in which the control names are displayed. Press the , buttons to reset immediately. Restore all factory default settings except "LANGUAGE." To adjust the contrast of the screen.
19 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual.
20 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Exit : Exit , : Move : Select another sub-menu Turn on the SUPER ENERGY SAVING fuction. When current setting value is ON,the SUPER SAVING color is green. Turn off the SUPER ENERGY SAVING function.
21 On Screen Display(OSD) Selection and Adjustment SUPER SAVING LED SAVING 19 inch 3 3 4 15 5 17 22 inch 24 inch Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal.
22 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display co.
23 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO button to automatically adjust your display image to the ideal setting.
24 Display image is incorrect T roubleshooting ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot.
25 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0 . 300 mm x 0 . 300 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 61 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
26 Specifications E191 1S 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 47.0 cm 0 . 300 mm x 0 . 300 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 61 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
27 Specifications E221 1T 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0 . 248 mm x 0 . 248 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
28 Specifications E221 1S 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 cm 0 . 248 mm x 0 . 248 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
29 Specifications E241 1T 60.97 cm (24 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 60.97 cm 0 . 277 mm x 0 . 277 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync.
30 Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode E2211T/E2211S/E2411T 1 2 3 4 5 6 7 8 9 10 11 *12 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 31.
31 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Separate the stand by pushing the PUSH button. Warning: You can hurt your finger.
32 Installing the W all mount plate Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.
M a k e s u r e to r e a d t h e Sa fe t y P r e c a u t i o n s befor e using the product . K e e p t h e O W N E R ’ S M A N U A L (C D ) i n a n acces sible place f or furture ref erence. The mod el a nd se ria l nu mbe r of the SET is located on the back o r one s ide of t he SET .
デバイスLG E1911S-BNの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
LG E1911S-BNをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG E1911S-BNの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG E1911S-BNの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG E1911S-BNで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG E1911S-BNを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG E1911S-BNの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG E1911S-BNに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG E1911S-BNデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。