Appleメーカー550Cの使用説明書/サービス説明書
ページ先へ移動 of 174
Service Source K Macintosh Po werBook 550c This product is forJapan only..
Service Source K Basics Macintosh Po werBook 550c.
Basics General Information - 1 General Information The Macintosh PowerBook 550c features a built-in trackpad, intelligent batteries, two battery bays, an optional PCMCIA expansion module, a darker shade of plastics, and a 10.4" display. The computer is available in Japan only.
Basics Rear Panel - 2 Rear Panel The illustration below shows the location of ports and connectors on the rear panel of the Macintosh PowerBook 550c..
Basics PowerBook Screw Matrix - 3 PowerBook Screw Matrix Nine different types of screws are used in the Macintosh PowerBook 550c. All are Torx screws and require either a T-8 or T-6 Torx screwdriver. Note: The legend for the screws follows on the next page.
Basics PowerBook Screw Matrix - 4 Legend f or Macintosh Po werBook 550c Screws 1 Feet 2 Hard drive, keyboard, bottom case (middle front), display assembly, floppy drive, daughterboard EMI shield (top .
Basics PowerBook Cable Matrix - 5 PowerBook Cable Matrix For a matrix of cables that work with specific models of the PowerBook family of computers, refer to the PowerBook Cable Matrix. (The Macintosh PowerBook 550c uses the same cables as the Macintosh PowerBook 520/540 Series.
Basics PCMCIA Module Handling - 6 PCMCIA Module Handling The PCMCIA (Personal Computer Memory Card International Association) expansion module is an option for the Macintosh PowerBook 550c. The module inserts into the computer’s second (left) battery bay and has two slots that accept a variety of third-party PCMCIA cards.
Basics PCMCIA Module Handling - 7 computer will shut down and all RAM contents will be lost. • Eject the PCMCIA module using the lever at the front of the module; eject a PCMCIA card using the PCMCIA Eject control panel or the PCMCIA Quick Eject module in the computer’s Control Strip.
Basics Battery Information - 8 Battery Information The Macintosh PowerBook 550c includes two nickel- metal-hydride (NiMH) batteries. Each battery provides power for up to 3.5 hours of work time, depending on the battery conservation features employed.
Basics Battery Information - 9 Battery Handling ± W arning: NiMH batteries contain toxic materials. Send undamaged, dead batteries to Apple for recycling—do not discard dead batteries with other waste. If the battery is damaged, do not return it to Apple.
Basics Battery Information - 10 • Keep the battery in a cool, dark place; do not store it for longer than 6 months without recharging. • If you are using one battery: Completely discharge and then recharge the battery once every 90 days. • If you are using two batteries: Swap the left and right batteries every month.
Service Source K Specifications Macintosh Po werBook 550c.
Specifications Processor - 1 Processor CPU Motorola 68040 microprocessor 66/33 MHz Addressing 32-bit internal registers 32-bit address bus 32-bit data bus.
Specifications Memory - 2 Memory RAM 4 MB RAM installed on the daughterboard Expandable to 12 MB with 8 MB Apple RAM expansion card Expandable to 36 MB with third-party RAM expansion card RO M 2 MB PR.
Specifications Disk Storage - 3 Disk Storage Floppy Drive 15 mm high, internal, 1.4 MB Apple SuperDrive Hard Drive 2.5 in., 750 MB hard drive.
Specifications I/O Interfaces - 4 I/O Interfaces SCSI HDI-30 SCSI port with 1.5 MB/sec. transfer rate Supports up to six external SCSI devices Connect SCSI device to computer with HDI-30 SCSI system cable.
Specifications I/O Interfaces - 5 V ideo Micro DV-14 video-out port; 8 bit, 256 color video output Supports most Macintosh, VGA, and SVGA monitors Ethernet High-speed Ethernet port; Apple AUI connecto.
Specifications I/O Devices - 6 I/O De vices K eyboard Built-in keyboard with 12 function keys 76 keys domestic, 77 keys ISO Two-level tilt adjustment T rackpad Solid-state trackpad Microphone Electret.
Specifications Sound and Video - 7 Sound and V ideo Sound Generator Apple sound chip provides 16-bit sound capable of driving stereo headphones or other stereo equipment through the sound jack Built-in stereo speakers V ideo Display 10.
Specifications Electrical - 8 Electrical Main Battery Two nickel-metal-hydride (NiMH) batteries Up to 3.5 hours of usage per battery before recharging Recharge time: 2 hours in shut down or sleep mode.
Specifications Physical - 9 Physical Dimensions Height 2.25 in. (5.7 cm) Width 11.5 in. (29.2 cm) Depth 9.65 in. (24.5 cm) W eight 7.3 lb. (3.3 kg).
Specifications Environmental - 10 En vironmental Operating T emperature 50–104°F (10–40°C) Storage T emperature -13 to 140°F (-25 to 60°C) Relative Humidity 20–80% noncondensing Operating Altitude 0–10,000 ft. (0–3048 m) Storage Altitude 0–15,000 ft.
Specifications Other - 1 1 Other Internal Modem Sends and receives data at 19.2 bps; sends and receives faxes at 14.4 bps SCSI Adapter Enables connection between PowerBook computer and desktop Macinto.
Service Source K Troubleshooting Macintosh PowerBook 550c.
Troubleshooting General - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether or not the product continues to exhibit the symptom.
Troubleshooting Power Manager Reset - 2 Power Manager Reset Reset the power manager if • The battery and power adapter are proven good, but the computer will not power on. • The computer will not reset after a system crash. To reset the power manager in the Macintosh PowerBook 550c, • Remove the AC adapter and the battery.
Troubleshooting A C Adapter Voltage Test - 3 AC Adapter Voltage Test To test the AC adapter voltage, • Use narrow test probes for the leads on your voltmeter • Make all measurements with the negat.
Troubleshooting Symptom Charts/ Startup - 4 Symptom Charts Startup RAM failure occurs (eight-tone error chord sounds after startup chord) 1 Reseat RAM expansion card and check connection. 2 Replace RAM expansion card. 3 Replace daughterboard. 4 Replace motherboard.
Troubleshooting Symptom Charts/ Power - 5 Power Screen is blank; computer doesn’t respond 1 Restart computer. 2 Connect power adapter and restart computer in 3–4 minutes. 3 Try known-good, charged main battery. 4 Check all interconnect board, daughterboard, and motherboard connections.
Troubleshooting Symptom Charts/ Power (Continued) - 6 Power (Continued) After you remove main battery, some Control Panel settings are different 1 Check cables. 2 Replace backup battery. 3 Replace interconnect board. 4 Replace daughterboard. 5 Replace motherboard.
Troubleshooting Symptom Charts/ Power (Continued) - 7 Power (Continued) Low-power warning appears 1 Recharge battery or attach power adapter. 2 Verify that peripherals are low-power. 3 Reduce use of floppy or hard drive, modem, sound, backlight, or other power-consuming devices, or connect power adapter.
Troubleshooting Symptom Charts/ Power (Continued) - 8 Power (Continued) Computer won’t power up 1 Restart computer. 2 Connect power adapter and restart computer in 3–4 minutes. 3 Try known-good power adapter. Verify power adapter tip is not chipped or cracked.
Troubleshooting Symptom Charts/ Video - 9 Video Pixel never comes on or is always on If more than five pixels do not come on or are always on, replace display. Partial or full row of pixels is always on or never comes on 1 Check cables. 2 Replace interconnect board.
Troubleshooting Symptom Charts/ Video (Continued) - 1 0 Video (Continued) Display is very light or totally white 1 Adjust screen contrast and brightness settings. 2 Verify cable, inverter board, interconnect board, daughterboard, and motherboard connections.
Troubleshooting Symptom Charts/ Video (Continued) - 1 1 Video (Continued) Backlight doesn’t operate 1 Verify that backlight cable connection is secure. 2 Check cable, inverter board, interconnect board, daughterboard, and motherboard connections. 3 Verify that cables are not pinched or severed.
Troubleshooting Symptom Charts/ Video (Continued) - 1 2 Video (Continued) No display, but computer appears to operate correctly 1 Press any key to wake computer from system sleep. 2 Adjust screen contrast and brightness settings. 3 Verify cable, inverter board, trackpad, keyboard, inter- connect board, daughterboard, and motherboard connections.
Troubleshooting Symptom Charts/ Floppy Drive - 13 Floppy Drive Audio and video present, but internal floppy drive does not operate 1 Try known-good floppy disk. 2 Check floppy drive cable connection. 3 Replace floppy drive cable. 4 Replace floppy drive.
Troubleshooting Symptom Charts/ Floppy Drive (Continued) - 1 4 Floppy Drive (Continued) Disk does not eject 1 Switch off system and hold trackpad button down while you switch system on. 2 Eject disk manually by carefully inserting opened paper clip into hole near floppy drive slot.
Troubleshooting Symptom Charts/ Floppy Drive (Continued) - 1 5 Floppy Drive (Continued) Disk initialization fails 1 Try known-good floppy disk. 2 Check floppy drive cable connection. 3 Replace floppy drive cable. 4 Replace floppy drive. Read/write/copy error 1 Try known-good floppy disk.
Troubleshooting Symptom Charts/ Hard Drive - 16 Hard Drive Internal hard drive does not operate 1 Make sure power adapter is connected. 2 Disconnect external SCSI devices. 3 Check hard drive cable connection. 4 Use HD SC Setup to reinitialize drive. 5 Replace hard drive cable.
Troubleshooting Symptom Charts/ Peripheral - 17 Peripheral After you connect external SCSI device, computer does not boot 1 Switch on external SCSI device before starting computer. 2 Check cable connections. 3 Verify that SCSI chain is terminated correctly.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 1 8 Peripheral (Continued) Cursor does not move when you are using trackpad 1 Reset the power manager. 2 Check trackpad connections. 3 Check interconnect board, keyboard, and motherboard connections.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 1 9 Peripheral (Continued) Cursor intermittently does not move or moves erratically 1 Reset the power manager. 2 Clean trackpad surface. 3 Check trackpad connections. 4 Replace trackpad. 5 Replace keyboard.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 2 0 Peripheral (Continued) Cursor moves, but clicking trackpad button has no effect 1 Reset the power manager. 2 Check trackpad connections. 3 Check interconnect board, keyboard, and motherboard connections.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 2 1 Peripheral (Continued) Known-good direct- connect printer does not print 1 Verify that System is 7.1.1 or later. 2 Verify that Chooser and Control Panel settings are correct. 3 Check cables.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 2 2 Peripheral (Continued) Known-good network printer does not print 1 Verify that System is 7.1.1 or later. 2 Verify that Chooser and Control Panel settings are correct. 3 Check cables. 4 Replace printer cable.
Troubleshooting Symptom Charts/ Peripheral (Continued) - 2 3 Peripheral (Continued) Device connected to external modem port doesn’t work 1 Verify that External Modem is selected in CDEV. 2 Verify that System is 7.1.1 or later. 3 Check cables. 4 Test device with known-good computer.
Troubleshooting Symptom Charts/ Internal Modem - 24 Internal Modem Internal modem options do not appear in CDEV 1 Verify that System is 7.1.1 or later.
Troubleshooting Symptom Charts/ Internal Modem (Continued) - 2 5 Internal Modem (Continued) Strange mix of characters appears on screen 1 Verify that baud rate and data format settings of communications application are compatible with internal modem and remote modem.
Troubleshooting Symptom Charts/ Internal Modem (Continued) - 2 6 Internal Modem (Continued) Modem does not respond to incoming call 1 If computer is in sleep mode, verify that Wake On Ring option in CDEV is selected. 2 Check phone cord connection and operation.
Troubleshooting Symptom Charts/ Internal Modem (Continued) - 2 7 Internal Modem (Continued) Modem connects but does not communicate with remote modem 1 Verify that remote modem needs error correction (error correction is internal modem default). 2 If remote modem does not need error correction, type AT &Q0 to disable error correction.
Troubleshooting Symptom Charts/ Internal Modem (Continued) - 2 8 Internal Modem (Continued) You are using System 7.5 and two messages appear: “This Macintosh may not have been shut down properly” and “Incoming fax cannot be received because internal modem could not be identified.
Troubleshooting Symptom Charts/ PCMCIA Module - 2 9 PCMCIA Module PCMCIA card won’t eject 1 Make sure PCMCIA slot is not blocked. 2 Insert straightened paper clip into hole next to slot.
Troubleshooting Symptom Charts/ Miscellaneous - 3 0 Miscellaneous Screen goes blank and computer shuts down every few minutes Computer is going into system sleep to conserve battery power. Adjust sleep delays in Control Panel or connect power adapter.
Troubleshooting Symptom Charts/ Miscellaneous (Continued) - 3 1 Miscellaneous (Continued) No sound from speaker 1 Verify that volume setting in Control Panel is above 0. 2 Verify that no external speaker is plugged in. 3 Check connections of speaker to interconnect board and interconnect board to motherboard.
Service Source K T ake Apart Macintosh Po werBook 550c.
Take Apart Battery/PCMCIA Module - 1 Battery/PCMCIA Module Before you begin, discon- nect the power adapter. Note: This procedure covers removal of the main battery, second battery or PCMCIA expansion module, and battery contact cover. Important: Before removing the battery, use the Macintosh Shut Down command.
Take Apart Battery/PCMCIA Module - 2 Caution: The Macintosh PowerBook 550c contains devices that are very susceptible to ESD damage. To prevent damage, wear a grounding wriststrap. Review the ESD precautions in Bulletins/Safety. 1 Slide the release button toward you and pull out the main battery on the right side of the computer.
Take Apart Battery/PCMCIA Module - 3 3 Note: The battery bezel includes a separate latch and latch spring. Remove the bezel carefully so these parts do not fall out. If you are replacing the battery bezel, pry up both ends of the bezel and lift it off the main battery.
Take Apart Battery/PCMCIA Module - 4 4 If you are replacing the battery contact cover, press in on the sides of the cover and slide it off the main battery.
Take Apart Battery/PCMCIA Module - 5 5 Note: Complete the following step if a PCMCIA expansion module is installed in the computer. Using the tip of your finger, rotate the lever at the front of the PCMCIA module toward you. 6 Note: You may have to use some force when pulling the module out of the computer.
Take Apart Keyboard - 6 Keyboard Before you begin, remove the battery/PCMCIA module. Keyboard.
Take Apart Keyboard - 7 1 Using a T-8 torx driver, remove the middle two bottom housing screws..
Take Apart Keyboard - 8 2 Using a small flat-blade screwdriver, lift the front of the keyboard and pull it forward slightly. 3 Rotate the keyboard so that it is perpendicular to the top cover.
Take Apart Keyboard - 9 4 Release the locking tabs on the two keyboard cable connectors and disconnect the cables from the motherboard. 5 Lift off the keyboard.
Take Apart Hard Drive - 10 Hard Drive Before you begin, remove the following: • Battery/PCMCIA module • Keyboard Hard Drive.
Take Apart Hard Drive - 11 1 Using a T-8 torx driver, remove the hard drive mounting screw..
Take Apart Hard Drive - 12 2 Using a small flat-blade screwdriver, pry up the front of the hard drive and slide it forward 1/2 inch. 3 Note: Use a rocking motion to disconnect the hard drive cable from the hard drive. Lift the drive partway out of the unit and disconnect the hard drive cable.
Take Apart Hard Drive - 13 5 If you are replacing the hard drive, remove the four screws and remove the hard drive bracket and insulator. Replacement Note: Reinstall the hard drive bracket and insulator on the replacement hard drive.
Take Apart Clutch Covers - 1 4 Clutch Covers Before you begin, remove the battery/PCMCIA module. Clutch Cover Clutch Cover.
Take Apart Clutch Covers - 1 5 1 Open the unit and rotate the display assembly as far back as it will go. 2 Using a flat-blade screwdriver and your fingers, press in on both sides of the wide end of the right clutch cover and release the two front latches.
Take Apart Clutch Covers - 1 6 Replacement Caution : Be careful not to pinch or rip the display cable when you replace the right clutch cover..
Take Apart Display Access Cover - 1 7 Display Access Cover Before you begin, remove the battery/PCMCIA module. Display Access Cover.
Take Apart Display Access Cover - 1 8 1 Open the unit and rotate the display assembly as far back as it will go. 2 Using a small flat-blade screwdriver, pry up the display access cover at the three slots in the front of the cover. 3 Remove the display access cover.
Take Apart Display Assembly - 1 9 Display Assembly Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover Display Assembly.
Take Apart Display Assembly - 2 0 Caution: Support the display assembly from beneath before removing it. 1 Open the unit and rotate the display assembly as far back as it will go. 2 Disconnect the interconnect-to-logic- board cable. 3 Using a T-8 torx driver, remove the two display mounting screws.
Take Apart Display Assembly - 21 interconnect-to-logic- board cable. 5 Remove the display assembly..
Take Apart Center Base Cover - 2 2 Center Base Cover Before you begin, remove the following: • Battery/PCMCIA module • Keyboard Center Base Cover.
Take Apart Center Base Cover - 2 3 1 Using a T-8 torx driver, remove the two rear panel screws. Replacement Caution: When replacing the rear panel screws, be sure to install the right screw first (the screw nearest the SCSI port).
Take Apart Center Base Cover - 2 4 2 Pull the center base cover forward slightly and slide it 1/2 inch to the right to release the two screw carriers. 3 Remove the center base cover.
Take Apart Floppy Drive - 25 Floppy Drive Before you begin, remove the following: • Battery/PCMCIA module • Keyboard • Center base cover Floppy Drive.
Take Apart Floppy Drive - 26 1 Using a T-8 torx driver, remove the two floppy drive screws..
Take Apart Floppy Drive - 27 2 Using a small flat-blade screwdriver, pry up the cable end of the floppy drive and slide the drive 1/2 inch to the left. 3 Slide the drive forward slightly and lift it partway out of the unit. 4 Disconnect the floppy drive cable from the motherboard and remove the drive.
Take Apart Floppy Drive - 28 Replacement Caution: Before disconnecting the floppy drive cable from the drive, note the cable folds and the correct orientation of the cable connection. Because the cable connector is not keyed, the floppy drive cable could be reinserted upside down.
Take Apart Floppy Drive - 29 5 If you are replacing the floppy drive or floppy drive cable, release the locking tabs and disconnect the cable from the drive.
Take Apart Floppy Drive - 30 6 If you are replacing the floppy drive, remove the two right bracket screws and remove the right bracket. 7 Remove the two left bracket screws and remove the left bracket.
Take Apart Floppy Drive - 31 Replacement Note: Reinstall the floppy drive brackets and floppy drive cable on the replacement floppy drive. Use the following procedure for the brackets: • Start the screws in the right bracket. • Push the front of the bracket toward the top of the floppy drive.
Take Apart Floppy Drive - 32 Replacement Caution: If the brackets are not pushed toward the top of the floppy drive, the floppy disk may not eject properly.
Take Apart Daughterboard EMI Shield - 3 3 Daughterboard EMI Shield Before you begin, remove the following: • Battery/PCMCIA module • Keyboard • Center base cover Daughterboard EMI Shield.
Take Apart Daughterboard EMI Shield - 3 4 1 Remove the three mounting screws. 2 Using a small flat-blade screwdriver, pry up and remove the daughterboard EMI shield. Replacement Caution: Make sure all the tabs on the sides of the shield fit inside the daughterboard guide.
Take Apart Daughterboard - 3 5 Daughterboard Before you begin, remove the following: • Battery/PCMCIA module • Keyboard • Center base cover • Daughterboard EMI shield • RAM card (if installe.
Take Apart Daughterboard - 3 6 Note: To remove the daughterboard, you will need to adapt an IC extractor so that it has a wide grip. 1 Grasp an IC extractor by the legs and pull outward.
Take Apart Daughterboard - 3 7 2 Remove the plastic retainer bar. 3 Note: The daughterboard is connected to the motherboard below the RAM card connector. Caution: You may have to use some force to disconnect the daughter- board. Use an IC extractor, as illustrated.
Take Apart Top Case - 3 8 Top Case Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Cen.
Take Apart Top Case - 3 9 1 Rotate the feet to the up position. 2 Using a T-8 torx driver, remove the screw located under each foot. 3 Remove the four screws at the front edge of the bottom case.
Take Apart Top Case - 4 0 4 Remove the remaining screw on the inside top edge of the case..
Take Apart Top Case - 4 1 5 Caution: The top case is connected to the motherboard by the trackpad cable. Be careful not to lift the top case too far off the unit or you may damage the cable. Carefully lift and rotate the top case toward you and disconnect the trackpad cable from the motherboard.
Take Apart Top Case - 4 2 6 Remove the interconnect-to-logic board cable from the opening for the right clutch. 7 Remove the top case. Replacement Note: Before securing the top case to the bottom case, thread the interconnect-to-logic board cable through the opening for the right clutch.
Take Apart Fuse - 4 3 Fuse Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base.
Take Apart Fuse - 4 4 Using a small flat-blade screwdriver, pry up and remove the fuse. Fuse.
Take Apart Interconnect-to-Logic-Bd. Cable - 45 Interconnect-to- Logic-Bd. Cable Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Displa.
Take Apart Interconnect-to-Logic-Bd. Cable - 46 Caution: Before discon- necting the interconnect- to-logic-board cable, note the correct orientation of the cable connection. Because the connector is not keyed, the cable could be reinserted upside down.
Take Apart Side Panels - 47 Side Panels Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive .
Take Apart Side Panels - 48 1 Using a T-8 torx driver, remove the right side- panel mounting screw. 2 Lift the panel slightly, slide it back, and remove it from the CPU stiffener. 3 Using a T-8 torx driver, remove the three left side-panel mounting screws.
Take Apart CPU Stiffener - 49 CPU Stiffener Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base cover • Floppy drive • Daughterboard EMI shield • Top case • Interconnect-to-logic- bd.
Take Apart CPU Stiffener - 50 Note: In this take-apart procedure, the CPU stiffener is removed with the side panels attached. This procedure also explains how to remove the panels from the stiffener.
Take Apart CPU Stiffener - 51 2 Rotate the feet to the up position. 3 Lift the CPU stiffener straight off the unit. CPU Stiffener.
Take Apart CPU Stiffener - 52 Note: If you are replacing the CPU stiffener, remove the side panels. 4 Using a T-8 torx driver, remove the right side- panel screw. 5 Lift the panel slightly, slide it back, and remove it from the CPU stiffener. 6 Using a T-8 torx driver, remove the three left side-panel screws.
Take Apart CPU Stiffener - 53 Replacement Caution: Make sure both EMI clips fold on top of the clutch pegs. If the right clip accidentally folds backward and touches the pins for the power connector, the contact could short out the motherboard.
Take Apart Lifter Feet - 54 Lifter Feet Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base cover • Floppy drive • Daughterboard EMI shield • Top case • Interconnect-to-logic- bd.
Take Apart Lifter Feet - 55 1 Remove the mounting screw and washer for the right lifter foot, and remove the foot. 2 Repeat for the left lifter foot. Lifter Lifter Foot Foot.
Take Apart Motherboard - 5 6 Motherboard Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base cover • Floppy drive • Daughterboard EMI shield • Top case • Interconnect-to-logic- bd.
Take Apart Motherboard - 5 7 1 Remove the motherboard mounting screw and standoff. 2 Carefully pry the motherboard from the positioning peg located below the standoff. 3 Slide the board forward 1/4 inch. 4 Caution: In lifting the motherboard, be careful that the sound-in and sound-out ports clear the openings in the rear panel.
Take Apart Motherboard - 5 8 5 If you are replacing the motherboard, discon- nect the RAM card (if installed), daughter- board, and modem card (if installed).
Take Apart Motherboard - 5 9 Replacement Note: Make sure the front of the motherboard fits securely below the positioning peg on the bottom case. Positioning Peg.
Take Apart Hard Drive Cable - 6 0 Hard Drive Cable Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base cover • Floppy drive • Daughterboard EMI shield • Top case • Interconnect-to-logic- bd.
Take Apart Hard Drive Cable - 6 1 1 Turn over the motherboard. 2 Disconnect the hard drive cable from the motherboard. Hard Drive Cable.
Take Apart Rear Door - 62 Rear Door No preliminary steps are required. Rear Door.
Take Apart Rear Door - 63 1 Open the rear door. 2 Carefully bend the door so that the middle bows downward. 3 Unhinge the bottom door pegs and remove the rear door.
Take Apart Bottom Case - 6 4 Bottom Case To remove the bottom case, remove the following: • Battery/PCMCIA module • Rear door • Clutch covers • Display access cover • Display assembly • Keyboard • Hard drive • Center base cover • Floppy drive • Daughterboard EMI shield • Top case • Interconnect-to-logic- bd.
Take Apart Bottom Case - 6 5 • CPU stiffener • Motherboard.
Take Apart Mi crophone Assembly - 6 6 Microphone Assembly Before you begin, remove the following: • Battery/PCMCIA module • Display access cover Microphone Assembly.
Take Apart Mi crophone Assembly - 6 7 1 Carefully disconnect the microphone cable from the interconnect board. 2 Using a small flat-blade screwdriver, pry up and remove the microphone assembly.
Take Apart Backup Battery - 6 8 Backup Battery Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • Hard d.
Take Apart Backup Battery - 6 9 1 Using a small flat-blade screwdriver, pry up and remove the backup battery cover. Backup Battery Cover.
Take Apart Backup Battery - 7 0 2 Carefully disconnect the backup battery cable. 3 Remove the cable from the cable guides. 4 Pry up and remove the backup battery and cable.
Take Apart Trackpad Assembly - 7 1 Trackpad Assembly Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • .
Take Apart Trackpad Assembly - 7 2 1 Disconnect the backup battery cable. 2 Using a T-8 torx driver, remove the front two mounting screws. Backup Battery Cable Connector.
Take Apart Trackpad Assembly - 7 3 3 Note: The trackpad cable assembly includes the display actuator switch and the trackpad button. Disconnect the trackpad cable assembly and remove it from the unit. Replacement Note: Recon- nect the backup battery cable before reconnecting the trackpad cable assembly.
Take Apart Trackpad Assembly - 7 4 4 Using a T-8 torx driver, remove the remaining two mounting screws. 5 Pry up and remove the trackpad actuator assembly.
Take Apart Trackpad Assembly - 7 5 6 With your fingers, push up from underneath the trackpad logic board and remove it from the top case. Trackpad Logic Board.
Take Apart Display Bezel Assembly - 7 6 Display Bezel Assembly Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly Display.
Take Apart Display Bezel Assembly - 7 7 1 Remove the microphone from the plastic retainer. 2 Disconnect the speaker cable from the interconnect board. 3 Remove the bottom two bezel mounting screws.
Take Apart Display Bezel Assembly - 7 8 4 Pry off the two rubber bumpers. 5 Remove the top two bezel mounting screws. Rubber Bumper.
Take Apart Display Bezel Assembly - 7 9 6 Note: Two hooks on each side of the bezel secure it to the rear housing. Pull the display bezel forward and lift it off the rear housing.
Take Apart Display - 80 Display Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Display bezel assembly Note: The display EMI shield is attached to the display with adhesive.
Take Apart Display - 81 1 Fold back the display EMI shield from the top and side edges of the display. 2 Remove the four mounting screws. 3 Disconnect the backlight cable from the inverter board. 4 Disconnect the interconnect-to- display cable from the interconnect board.
Take Apart Display - 82 6 If you are replacing the display, disconnect and remove the inter- connect-to-display cable from the back of the display. Connector Interconnect-to-Display Cable.
Take Apart Inverter Board - 83 Inverter Board Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Display bezel assembly Note: The display EMI shield covers the inverter board and attaches to the display with adhesive.
Take Apart Inverter Board - 84 1 Fold back the display EMI shield from the right edge of the display. 2 Remove the inverter board mounting screw. 3 Disconnect the interconnect-to- inverter cable and the backlight cable.
Take Apart Interconnect Board - 8 5 Interconnect Board Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Display bez.
Take Apart Interconnect Board - 8 6 1 Disconnect the interconnect-to- display cable and the interconnect-to- inverter cable. 2 Remove the two mounting screws.
Take Apart Interconnect-to-Inverter Cable - 87 Interconnect-to- Inverter Cable Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display .
Take Apart Interconnect-to-Inverter Cable - 88 1 Disconnect the interconnect-to- inverter cable from the interconnect and inverter boards. 2 Remove the cable.
Take Apart Interconnect-to-Display Cable - 89 Interconnect-to- Display Cable Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display as.
Take Apart Interconnect-to-Display Cable - 90 1 Disconnect the interconnect-to- display cable from the back of the display. 2 Remove the cable. Interconnect-to-Display Cable Connector.
Take Apart Clutches - 9 1 Clutches Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Display bezel assembly Clutch C.
Take Apart Clutches - 9 2 1 Remove the mounting screw for the right clutch and remove the clutch. 2 Repeat for the left clutch..
Take Apart Display EMI Shield - 93 Display EMI Shield Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Display beze.
Take Apart Display EMI Shield - 94 Remove the display EMI shield from the display rear housing. Display EMI Shield.
Take Apart Display Rear Housing - 9 5 Display Rear Housing To remove the rear housing, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly .
Service Source K Upgrades Macintosh Po werBook 550c.
Upgrades RAM Card - 1 RAM Card Before you begin, remove the following: • Battery/PCMCIA module • Keyboard • Center base cover • Daughterboard EMI shield Caution: Handle the RAM expansion card by the edges only. Do not touch any components on the card.
Upgrades RAM Card - 2 1 Remove the plastic retainer bar. 2 Caution: An incorrectly installed RAM card could damage the daughter- board. Note that the expansion connector and the RAM card are keyed for proper installation. Do not defeat the key by forcing the card into the connector.
Upgrades RAM Card - 3 not to apply pressure to any components or you may permanently damage the card. Place the edge of the RAM card in the two guides. Using the RAM card alignment tool for correct positioning, connect the card to the expansion connector on the daughterboard.
Upgrades RAM Card - 4 Note: To verify that the upgrade is successful, check the Total Memory message (for systems with virtual memory switched off) or the Built-in Memory message (for systems with virtual memory switched on). The memory size should be 4 MB of soldered RAM plus the RAM on the expansion card.
Upgrades Modem and DAA Cards - 5 Modem and DAA Cards Before you begin, remove the following: • Battery/PCMCIA module • Clutch covers • Display access cover • Display assembly • Keyboard • .
Upgrades Modem and DAA Cards - 6 • CPU stiffener • RAM card (if installed) Note: The modem is a Macintosh PowerBook 550c option. This procedure explains how to install the modem and DAA cards and also includes special instructions on how to remove the modem.
Upgrades Modem and DAA Cards - 7 1 Slide the modem card under the RAM card guides and connect the modem card to the motherboard. 2 Pull up and remove the modem cap.
Upgrades Modem and DAA Cards - 8 3 Install the modem port frame on the DAA card. 4 Note: The connector for the DAA card is on the underside of the right end of the card.
Upgrades Modem and DAA Cards - 9 6 Note: The following page explains how to remove the modem card. To remove the card, you will need to adapt an IC extractor so that it has a wide grip.
Upgrades Modem and DAA Cards - 1 0 7 To remove the modem card, place the legs of the IC extractor in the notches at the end of the board and pull up. Notch Notch.
Upgrades PCMCIA Module Upgrade - 1 1 PCMCIA Module Upgrade Before you begin, remove the second (left) battery. Important: Before removing the battery or inserting the PCMCIA expansion module into the computer, use the Macintosh Shut Down command. Otherwise, the computer will shut down automatically and all RAM contents will be lost.
Upgrades PCMCIA Module Upgrade - 1 2 Macintosh PowerBook 550c option. The module comes with a protec-tive cap and PCMCIA driver software. 1 Note: You will feel some resistance when you insert the PCMCIA expansion module into the computer. Continue to press the module in until it is firmly seated.
Upgrades PCMCIA Module Upgrade - 1 3 2 Note: Refer to the “PCMCIA Expansion Module User’s Guide” for directions on how to install the module software. Install the PCMCIA expansion module software. Note: Refer to “Battery/ PCMCIA Module” in Take Apart for directions on how to eject the module from the computer.
Service Source K Additional Procedures Po werBook 550c.
Additional Procedures Battery Verification - 1 Battery Verification The Control Strip on the PowerBook 500 Series desktop shows the battery charge and the rate at which the battery is being used. Use a voltmeter to measure the actual battery charge: 1 Set the voltmeter to the 10 volts DC scale.
Additional Procedures Battery Verification - 2 negative probe to the negative terminal. 3 A fully charged battery measures approximately 10.8 volts; a fully discharged battery measures 7.8 volts. Note: If a battery is stored outside the computer for extended periods, its voltage may drop to 5.
Additional Procedures Backup Battery Verification - 3 Backup Battery Verification The backup battery saves the PRAM and power management information on the logic board when the computer is shut down. To check that the backup battery is working, follow the procedures below.
Additional Procedures Backup Battery Verification - 4 6 To recharge the backup battery, leave the PowerBook plugged in for 48 hours. It is ok to use it while it is charging. 7 If the backup battery appears dead or will not charge, replace the backup battery.
Additional Procedures Adapter Verification - 5 Adapter Verification To verify the charge of the AC adapter, • Plug in the AC adapter to a wall socket. • Set a voltmeter to the 10 volts DC scale. • Touch the positive volt- meter probe to the inside of the adapter plug and touch the negative volt- meter probe to the outside of the plug.
Service Source K Exploded V ie w Macintosh Po werBook 550c.
Exploded View 1 Display Bezel Kit 076-0516 Display EMI Shield 922-1212 Microphone 922-0783 Inverter Board 922-1445 Interconnect-to-Inverter Cable 922-1554 Clutch 076-0299 Interconnect-to-Display Cable.
デバイスApple 550Cの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Apple 550Cをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはApple 550Cの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Apple 550Cの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Apple 550Cで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Apple 550Cを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はApple 550Cの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Apple 550Cに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちApple 550Cデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。