LG ElectronicsメーカーLMV1630WWの使用説明書/サービス説明書
ページ先へ移動 of 19
W ebsite: http://us.lgservice.com MICR O W A VE O VEN INST ALLA TION INSTR UCTIONS PLEASE READ AND SA VE THESE INST ALLA TION INSTRUCTIONS. P/NO.: 3828W5U 0 529.
– 2 – Y our Safety Fir st BEFORE Y OU ST ART • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The model number label is located on the oven front. See Figure 1. The mounting plate is located on back side of microwave oven.
– 3 – Y our Safety Fir st • THIS APPLIANCE MUST BE GROUNDED! – If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
– 4 – Y our Safety Fir st • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
– 5 – P ar ts, T ools, Materials THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector (for roof venting or wall venting installation) Not Actual Size (2 pieces must be assembled as shown) Not used if venting into kitchen.
– 6 – P ar ts, T ools, Materials Clear Tape (for taping the templates to the wall) Phillips Screwdriver (for the screws) Pencil Flat Blade Screwdriver (for the toggle bolts) Plumb Line Measuring T.
– 7 – STEP 1: Prepare The Electrical Connection Improper gr ounding could result in electric shoc k or other personal injury . 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. NOTE: The outlet should be on a circuit dedicated to the microwave oven (120V, 60 Hz.
– 8 – STEP 2: Prepare The V enting System THIS O VEN MUST BE PR OPERL Y VENTED! W ARNING NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 9. You may vent your oven in one of three ways.
– 9 – STEP 2: Prepare The V enting System Standard Fittings NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper ’ s sticking.
– 1 0 – STEP 3: Prepare The V enting Blo wer Your microwave oven is shipped with the blower assembled for roo m - vent ed . You need to adjust the blower if you want wall-vent ed or roo f -vented installation. • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock.
– 1 1 – STEP 3: Prepare The V enting Blower W ALL-VENTED INST ALLA TION: 1. Remove one blower unit mounting screw and one or several blower plate mounting screw(s). Remove the blower plate from cabinet. See Figure 1 3 . 2. Carefully lift the blower unit out of the microwave oven.
– 1 2 – STEP 3: Prepare The V enting Blo wer ROOF-VEN T ED INSTALLATION: 1. Remove one blower unit mounting screw and one or several blower plate mounting screw(s). R e m o v e t he b l o w e r p l a t e f r o m c a b i n e t . S e e Figure 19. 2.
– 1 3 – STEP 4: Prepare The W all & Upper Cabinet T o av oid per sonal injury or property damage , do not attempt to install this micro wave oven if y ou cannot find a wall stud.
– 1 4 – STEP 4: Prepare The W all & Upper Cabinet Drill The Holes In The W all And Upper Cabinet. 1. Drill holes on the circles. If there is a stud, drill a 3/16 " hole for lag screws. If there is no stud, drill a 3/4 " hole for toggle bolts.
– 1 5 – STEP 5: Install The Mounting Plate Center Line A C B Draw Center Line Draw Lines on Studs For Wall- Vented Only Minimum 66 " From the Floor Support Tab Support Tab E Mounting Plate D .
– 1 6 – STEP 5: Install The Mounting Plate Slide exhaust adaptor into guides on rear panel. Exhaust Adaptor Damper (hinge side up) Locking T abs Guides Mounting Plate Back Plate (1-piece Mounting Plate) (3-piece Mounting Plate) For W all-V ented Make the box cutout for the rear wall duct.
– 1 7 – STEP 6: Attach The Oven T o The W all 1. Carefully lift microwave oven and hang it on support tabs (See Figure 27) at the bottom of the mounting plate.Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet.
– 1 8 – STEP 6: Attach The Oven T o The W all Damper Power supply Cord Clamp 5. Roof venting installation: See Figure 33. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed.
Printed in China.
デバイスLG Electronics LMV1630WWの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
LG Electronics LMV1630WWをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG Electronics LMV1630WWの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG Electronics LMV1630WWの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG Electronics LMV1630WWで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG Electronics LMV1630WWを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG Electronics LMV1630WWの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG Electronics LMV1630WWに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG Electronics LMV1630WWデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。