LG ElectronicsメーカーLVC-C310NMの使用説明書/サービス説明書
ページ先へ移動 of 28
Operating Instructions LVC-C300HM/HP/NM/NP LVC-C310HM/HP/NM/NP LVC-C301HM/HP/NM/NP LVC-C311HM/HP/NM/NP LVC-C302HM/HP/NM/NP LVC-C312HM/HP/NM/NP LVC-C303HM/HP/NM/NP LVC-C313HM/HP/NM/NP Before installing and using the camera, please read these instructions throughly and retain them for later reference.
2 CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER(OR BACK) NO USER SERVICE- ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SER- VICE PERSONNEL.
Contents 3 FEA TURES The power zoom color video camera is designed for use in monitoring system. • High resolution and high sensitivity with a 1/4 inch CCD (Charge Coupled Device) • High magnitude.
Cautions for Safe Operation 4 Power Supply This camera must always be operated a 12V DC UL Listed, Class 2 Power Supply only. Handling of the unit Be careful not to spill water or other liquids on the unit, or to get combustible or metallic material inside the body.
Operating Controls and Their Functions 5 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera. 2. Lens mount cap 3. TELE Key When push the TELE KEY, picture is telephoto 4. WIDE Key When push the WIDE KEY, picture is wide angle 5.
Power In / Control 6 You can adjust focus and zoom by a pin terminal on the back side of the camera. 1 4 3 5 6 2 * is the color of the cable.(If it is offered) Adjust voltage from 1 pin and 2 pin.
External Key (A/D IN) 7 Schematic diagram of wired remote-control 1) C300'S 2) C310'S 6.8K 8.2K 12K 18K 33K 68K 180K.
MENU DESCRIPTIONS 8 Using TELE, WIDE, FOCUS+, FOCUS- button • TELE and WIDE are used for UP and DOWN . • FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data.
CAMERA ID 9 1. CAMERA ID To connect a large number of camera , It can be assigned to identification number to each camera for camera control easily. (OFF, 0 - 255 : total numbers of ID are 256) • It only can be set this function using ID commend. To transfer ID Code of camera , In first byte at PC control.
PUSH 2. Focus Set : 2-1. Focus Mode Set : This function is for focus mode setting A) Set up “FOCUS SET” in main menu using Menu key. Select the “FOCUS MODE” in submenu using Tele/Wide key. And then set the mode (Auto, Push auto, or Manual) using Focus key.
FOCUS MODE SET 11 2-4. ZOOM END Set : This function is for selection of zoom end position. A) Select the “ZOOM END” in submenu using Tele/wide key. B) Set the Zoom end mode from (Zoom Start + 1) x 270 to X using Focus key. 2-5. ZOOM SPEED Set : This function is for selection of zoom speed.
3. AWB SET 3-1. WB Mode Set : This function is for changing the WB mode. A) Set up “AWB SET” in main menu using Tele/wide key. B) Select the “WB MODE” in submenu using Tele/wide key. C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor, Special using Focus key.
A WB SET 13 3-3. BLUE ADJUST Set : This function is available for Special ,Push Auto, Manual WB mode. This mode is the adjustment of user option for special color. A) Select the “BLUE ADJUST” in submenu using Tele/wide key. B) Adjust the level from (-30 to 30 SPECIAL, -128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key.
4. AE SET 4-1. AE Mode Set : This function is for changing to AE mode. A) Set up “AE SET” in main menu using Tele/wide key. B) Select the “AE MODE” in submenu using Tele/wide key. C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using Focus key.
AE SET 15 4-4. BRIGHTNESS ADJUSTMENT Set : A) Select the “BRIGHTNESS” in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX . using Focus key. * ## : Current level at Auto mode. 4-5. BACKLIGHT Set : A) Select the “BACKLIGHT” in submenu using Tele/wide key.
4-7. SHUTTER SPEED Set : A) Select the “SHUTTER” in submenu using Tele/wide key. B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key. 4-8. INITIAL SET : A) Select the “INITIAL SET” in submenu using Tele/wide Command, B) Set the initial set mode to ON or OFF using Focus key.
SPECIAL SET 17 5. SPECIAL SET 5-1. User Title Set : This function is for custom title on screen display. A) Set “SPECIAL SET” in main menu using Tele/wide key. B) Select the “USER TITLE” in submenu using Tele/wide key. C) Set the position of title and set data using Tele / Wide, Focus key.
5-5. NEGATIVE Set : This mode is to change color and luminance to negative. A) Select the “COLOR” in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-6. WIDE BURST Set : This mode is to change color burst width for long dis- tance application.
MOTION DET 19 6. MOTION DETECTION SET 6-1. DETECTION Mode Set : A) Set “MOTION” in main menu using Tele/wide key. B) Select the “DETECTION” in submenu. Using Tele/wide key. C) Set the mode ON, OFF using Focus key. 6-2. LEVEL ADJUST Set : This function is available for DETECTION ON mode.
7. F. OSD SET 7-1. FUNCTION Set : A) Set “F. OSD” in main menu using Tele/wide key. B) Select the mode what you want in submenu using Tele/wide key. C) Set the display mode of OSD using Tele / Wide, Near/Far key. *INITIAL SET and RETURN are the same as before procedure.
E. SENSITIVITY SET 21 8. E. SENSITIVITY SET: (OPTION) 8-1. E. SENSITIVITY SET A) Select the “E.SENSITIVITY” in submenu using Tele/wide key. B) Select the sensitivity mode what you want in submenu using Focus key.
9. WDR SET (OPTION) 9-1. WDR SET A) Select the “WDR” in main menu using Tele/wide key. B) Select the “WDR CONTROL” in submenu using Tele/wide key. C) Select the WDR mode what you want in submenu using Focus key. * Mode sequence : OFF -- ON -- AUTO * WDR Auto mode is working at the condition of high light back light.
On Screen Display 23 Some of these functions will be displayed every time the camera is operated and then disappeared after 5 seconds. FUNCTION OSD Format Description 1. Focus Mode Non display Auto Mode Manual / push Auto Mode 2. Back Light Non display Back Light OFF “BL”display BLC ON / Auto BLC Mode 3.
FUNCTION OSD Format Description 6. WBC Mode White Balance AUTO Special Auto White Balance; Adjustment Mode according to change of external illuminant. RED ADJUST and BLUE ADJUST (0~255) are available. After changing R/B value, The mainternance mode is “AUTO”.
25 Specifications Image device 1/4 " interline transfer CCD NTST, High resolution : 811(H) X 508(V) 410K NTST, Normal resolution : 537(H) X 505(V) 270K PAL, High resolution : 795 (H) X 596 (V) 470K PAL, Normal resolution : 537(H) X 597(V) 320K Sync system Internal sync Horizontal resolution Approx.
Focal Length 3.24mm (WIDE), 86mm (TELE) OSD(On Screen Display) English Power requirement 12V DC UL Listed, Class 2 Power Supply only Video output Composite Output 75 Ω Terminated / Y,C Separated Power consumption 5.
.
P/NO: MFL30580130.
デバイスLG Electronics LVC-C310NMの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
LG Electronics LVC-C310NMをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG Electronics LVC-C310NMの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG Electronics LVC-C310NMの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG Electronics LVC-C310NMで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG Electronics LVC-C310NMを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG Electronics LVC-C310NMの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG Electronics LVC-C310NMに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG Electronics LVC-C310NMデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。