LG ElectronicsメーカーWD-1481RDの使用説明書/サービス説明書
ページ先へ移動 of 42
W ASHING MACHINE SER VICE MANUAL READ THIS MANUAL CAREFULL Y TO DIAGNOSE TROUBLES CORRECTL Y BEFORE OFFERING SERVICE. MODEL : WD-1431 1(6)RD/WD-1481RD WD-1231 1(6)RD WD-14312(7)RD/WD-14310(5)RD WD-123.
OC T . 2004 PRINTED IN KOREA P/No.:3828ER3035 G.
CONTENTS 1. SPECIFICA TION ............................................................................................................... .............3 2. FEA TURES & TECHNICAL EXPLANA TION .......................................................
3 1. SPECIFICA TION ITEM PO WER SUPPL Y PRODUCT WEIGHT W ASHING 140W SPIN 300W F AN MOTOR 25W DRAIN MOTOR 40W W ASH HEA TER DRY HEA TER W ASH 45rpm WD-1481RD/WD-1431 1RDA/WD-1431 1(6)RD/WD-14312(7)RD/.
■ Automatic process from washing to drying. Automatic process from washing to drying can be selected easily . W ashing capacity : 8kg/8.5kg/10.1kg(Cotton)/10kg Drying capacity : 4kg/4.
2-2.DETERMINE W ASHING TIME BY FUZZY LOGIC T o get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. 2-3.W A TER LEVEL CONTROL This model adopts a pressure sensor which can sense the water level in the tub.
3. P AR TS IDENTIFICA TION 6 ACCESSORIES Spanner .
Before servicing ask troubles of customers Check the adjustment(power supply is 220-240V~, remove the transit bolts....) Check the troubles referring to the trouble shooting. Decide service steps referring to disassembly instructions. And then, service and repair .
HOW TO CONNECT INLET HOSE Check that the rubber packing is inside of the valve connector . Connect the inlet hose firmly to prevent leak. CONNECT DRAIN HOSE CONNECT POWER PLUG 8 Make sure that the hose is not twisted. The drain hose should be placed under 100cm from the floor .
TEST OPERA TION 9 MAX max Connect the power plug to the outlet. In case of Coloreds program. Connect the inlet hose. Preparation for Press the POWER button.
10 5. OPERA TION • Use this button to turn the power On/Off . • Rotate the Cycle selector knob to select the cycle designed for different types of fabric and soil levels.
11 • INTENSIVE • DRY Button • Rinse, Spin, Temp. Button • TIME DELAY event unwanted use of the washer . W ASH button for 3 seconds to et, CHILD LOCK lights and all except the Power button. Y ou while it is operating. • If the laundry is heavily soiled “Intenive” option is effective.
12 6. WIRING DIAGRAM / PROGRAM CHAR T About 2:00 About 1:50 About 30 About 1:00 About 55 About 1:15 About 46 About 28 About 17 About 30 About 33 About 1:05 About 2:50.
13 7. TROUBLE SHOOTING 7-1.BEFORE SVC CHECKING Be careful of electric shock or disconnecting the parts while trouble shooting. V oltage of each terminal in 220-240V~ and DC while applying an electric current. 7-2.QC TEST MODE. Pressing Rinse, and Spin button simultaneously .
14 7-5.ERROR DISPLA Y. If you press the Start/Pause button in error condition, any error except ‘ ’ will disappear and the machine will change into pause status. In case of if the error is not resolved within 20 sec.
ERROR SYMPTOM CAUSE 8 9 10 • MAIN PWB ASSEMBL Y is out of order Replace the MAIN PWB ASSEMBL Y • Winding in the ST A TOR ASSEMBL Y is short-circuited.
16 8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERA TION 8. ERROR DIAGNOSIS AND CHECK LIST SYMPTOM GUIDE FOR SERVICE CALL NO POWER W ater inlet trouble Is the power plug connected firmly to 220-240V~ outle.
17 SYMPTOM • Door does not open • Error displayed on the program • DRAIN TROUBLE GUIDE FOR SERVICE CALL NO YES NO YES Started with door opened? NO YES Is the debris filter clogged with foreign material such as pin, coin and etc.
18 SYMPTOM GUIDE FOR SERVICE CALL Suds overflow from the appliance. (In this condition, wash and spin do not operate normally) No effect of softener YES YES YES YES YES Is low-sudsing detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? Recommend to reduce the using amount of detergent.
19 8-2.FAUL T DIAGNOSIS AND TROUBLE SHOOTING 1. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. 3. If you replace the MAIN PWB ASSEMBL Y , Put in the connectors correctly .
20 Is water supply shut-off? Is the tap opened? When you press both Rinse button and Spin button simultaneously , is the water level frequency below 240? Is the inlet valve filter clogged with impurity? Is resistance between each terminal of INLET V AL VE ASSEMBL Y is 2~8 k ? Check the voltage of the inlet valve connector 220-240V~.
21 YES YES NO NO NO NO YES YES YES YES Wiring diagram ABNORMAL SOUND SOFTENER DOES NOT FLOW IN Fix the bolt tightly . Replace the ST A TOR ASSEMBL Y or ROTOR ASSEMBL Y . Refer to NO W A TER SUPPL Y Check the wiring on the dispenser . Put it in the correct compartment.
22 Replace the S.PRESSURE SWITCH ASSEMBL Y Replace the MAIN PWB ASSEMBL Y Repair the DRAIN HOSE ASSEMBL Y . Remove foreign material. Reconnect or repair the connector Repair the DRAIN PUMP ASSEMBL Y .
23 AC 220-240V Push the THERMISTOR tightly to the rubber . When checking THERMISTOR on the tub is the THERMISTOR loosened above 2mm from the rubber? HEA TING CONTINUOUSL Y ABOVE THE SETTING W A TER TE.
24 NO YES YES YES NO NO NO YES (1) SPIN TROUBLE Check the S.PRESSURE SWITCH ASSEMBL Y or HOSE (Pressure). If the problem is on the S.PRESSURE SWITCH ASSEMBL Y or the HOSE, replace the S.PRESSURE SWITCH ASSEMBL Y or the HOSE. Normal Correct the connector .
Dry duct Condensing duct Thermistor Disassemble the cabinet cover and condensing bellows. Is there any foreign object in condensing bellows. Clean the bellows [dHE] ERROR DISPLAY CHECK FOR DRY HEATER TROUBLE CHECK FOR DRY FAN MOTOR TROUBLE NO YES Replace the thermistor.
26.
Black Yellow 20~30 27.
28.
9. DISASSEMBL Y INSTRUCTIONS Disassemble and repair the parts after pulling out power cord from the outlet. Unscrew the screws on the top plate. The plate assembly(T op) is pulled back and then upward to arrow direction. The cover(Inner) is disassembled.
30 The back cover is removed. T wo screws are unscrewed. Disconnect connector from the wiring. Pull the PWB assembly (Main) to arrow direction. The plate assembly(T op)and the cover(lnner)are disassembled. Pull the drawer to arrow direction.
31 Disconnect the wiring connector . Remove the valve by two screws of the valve holder . When reconnecting the connector 2 1 3 4 INLET VALVE V AL VE (DRY) YL/BK - BK V AL VE (PRE-.
32 The cabinet gasket clamp is released. T wo screws are unscrewed from the cabinet cover . Pull plat( - ) screwdriver or pully knife into the both sides of filter cover , and pull in out. Unscrew the screw from the lower side of the cabinet cover .
33 Disassemble the clamp assembly . Remove dry gasket clamp by loosening the screw . When reassembling the gasket, put the drain hole of the gasket downward, then assemble.
34 Remove the back cover . After loosening the bolt, Rotor , pull out the rotor . Remove the 6 bolt from the stator . Disconnect the 2 connectors. Remove the hinges (Damper) at the T ub. The Hinge(Damper) at the base is pulled of f pressing on the snaps at the sharp end.
Remove pump outlet hose. Remove tub pump bellows. Remove cap(Remaining Hose). Disconnect the wiring. Three screws are unscrewed from the cabinet. Remove the pump to arrow direction. Loosen the nut. Remove washing heater by pulling out.
The cabinet cover clamp is removed and the gasket is released. T wo screws are unscrewed. The door lock S/W is disconnected form the wiring connector and the strap. Remove washing heater . Remove the foreign object(wire,coin,etc) by inserting long bar in the hole.
Remove 6 screws and dry fan assembly . Remove 7 screws and dry duct upper . Remove 2 screws and dry heater . Remove thermostat. Remove 17 screws from Dry duct upper and Dry fan Assembly .
10-1.THE P ART LIST OF CABINET ASSEMBL Y 10. EXPLODED VIEW AND P AR T LIST 38 A150 A152 A140 A153 A151 A134 A270 A272 A274 A141 A131 A130 A440 A133 A303 A275 A276 A220 A201 A200 A410 A450 A430 A485 A1.
10-2 THE EXPLODED VIEW OF CONTROL P ANEL & DISPENSER ASSEMBL Y 39 F130 F430 F441 F210 F160 F170 F110 F120 F300 F321 F324 F462 F322 F436 F466 F215 F225 F220 F432 F320.
10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBL Y 40 K 111 K123 K122 K121 K410 F465 F464 K146 M105 K140 K560 K510 K131 K135 K130 K1 15 F145 K520 K540 K550 F467 F461 F468 K530 K61 1 K610 K105 K320 K12.
10-4 THE EXPLODED VIEW OF DR YER 41 M130 M120 M230 M216 M100 M101 M220 M240 M210 M215 M111 M110.
デバイスLG Electronics WD-1481RDの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
LG Electronics WD-1481RDをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLG Electronics WD-1481RDの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。LG Electronics WD-1481RDの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。LG Electronics WD-1481RDで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
LG Electronics WD-1481RDを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLG Electronics WD-1481RDの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、LG Electronics WD-1481RDに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLG Electronics WD-1481RDデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
