AppleメーカーLogic Boardの使用説明書/サービス説明書
ページ先へ移動 of 20
073-0665 Re v . D Xserve Logic Board Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions cov ering customer-installable par ts are av ailab le at http://www .
Xserve Logic Board - 2 3. If the ser v er is in the loc k ed position (the y ellow security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 4. If the cable management arm is not in use, unplug all e xternal cables e xcept the power cord.
Xserve Logic Board - 3 8. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 9. While depressing both le v ers , pull the bottom housing all the w a y forw ard and remo v e it from the rac k.
Xserve Logic Board - 4 Removing the Installed Logic Board Note: The replacement logic board does not include memor y DIMMs or expansion cards . Y ou must tr ansf er these par ts from the current logic board.
Xserve Logic Board - 5 Dual-Slot Riser 1. Release the thumb screw that secures the riser’ s cards to the ser ver . (Figure 4) 2. If there are latches on either side of the riser , lift them slightly to release the riser from the logic board.
Xserve Logic Board - 6 2. Pull the clip on the riser forw ard to release the riser from the logic board connector . (Figure 6) 3. Disconnect the riser from the logic board and remov e the riser and card from the ser v er . Figure 6 Heatsink and Processor , V ersion 1 Note: There are two versions of the Xserve heatsink and processor .
Xserve Logic Board - 7 3. Release the three captive scre ws that secure the heatsink. (Figure 8) 4. Lift the heatsink straight up and remo ve it from the server . Figure 8 5. Lift the processor straight up to disconnect it from the logic board. (Figure 9) 6.
Xserve Logic Board - 8 Heatsink and Processor , V ersion 2 1. Using a Phillips screwdriv er , remove the three scre ws that mount the heatsink and processor to the logic board. (Figure 10) 2. Carefully lift the heatsink and processor straight up and out of the server .
Xserve Logic Board - 9 A T A Controller Board 1. If necessar y , disconnect the blower cab le near the A T A controller board. (Figure 11) 2. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server .
Xserve Logic Board - 10 Po wer Supply 1. Release the locking latch on the po wer supply cab le connector and disconnect the cable from the driv e interconnect board. (Figure 12) 2. Release the thumbscrew that secures the po wer supply to the chassis .
Xserve Logic Board - 11 Logic Board 1. Release the thumb screw that secures the logic board to the chassis . (Figure 13) 2. Mov e the logic board f orw ard and up slightly to release it from the f our mounting pegs. 3. Tilt up the end of the logic board nearest the blo wers so that the board ports clear the chassis.
Xserve Logic Board - 12 Installing the Replacement Logic Board 1. If the heatsink thermal pad on the underside of the replacement logic board has protectiv e film on it, remov e the film. (Figure 14) Note: The protective film is a very thin layer on top of the thermal pad.
Xserve Logic Board - 13 Po wer Supply 1. Reconnect the pow er supply to the logic board. 2. Tighten the thumb screw that secures the po wer supply to the chassis . 3. Reconnect the pow er supply cable to the driv e interconnect board. A T A Controller Board 1.
Xserve Logic Board - 14 3. Reconnect the blo wer cab le , if you disconnected it earlier . Heatsink and Processor , V ersion 1 1. P osition the processor over its logic board connector and press do wn, being careful not to touch any chips on the board or processor .
Xserve Logic Board - 15 6. T o ensure the grease spreads e v enly ov er the processor , lightly tighten the screws in the order indicated below . (FIgure 19) 7. Again tighten the screws in the order indicated to secure the heatsink. Figure 19 8. Replace the heatsink duct on the heatsink.
Xserve Logic Board - 16 Heatsink and Processor , V ersion 2 1. Inser t the threaded end of one of the processor installation guides into the logic board standoff on the right side of the processor connector . T wist the guide until it scre ws into place.
Xserve Logic Board - 17 3. Carefully align the screw holes on the replacement heatsink and processor with the two guides, and lo wer the unit str aight down o v er the guides until it touches the logic board.
Xserve Logic Board - 18 5. Remov e the two installation guides . 6. Replace the three mounting screws and secure the processor and heatsink to the logic board. (Figure 22) Figure 22 PCI/A GP Card Risers and Memory DIMMs 1. Reconnect the dual- and single-slot risers to the logic board.
Xserve Logic Board - 19 Battery Remov e the battery insulator tab from the batter y holder on the replacement logic board. (Figure 23) Figure 23 Note: Replacing the logic board in the ser v er changes its Ethernet ID number . The new number is printed on an Ether net ID label pac kaged with the replacement logic board.
Xserve Logic Board - 20 Apple Computer , Inc. © 2003 Apple Computer , Inc. All rights reser v ed. This document is protected under U .S . Copyright La w and International T reaties, and no par t of this document ma y be reproduced in any f orm without written per mission from Apple.
デバイスApple Logic Boardの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Apple Logic Boardをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはApple Logic Boardの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Apple Logic Boardの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Apple Logic Boardで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Apple Logic Boardを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はApple Logic Boardの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Apple Logic Boardに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちApple Logic Boardデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
