ABC OfficeメーカーBA-FS43の使用説明書/サービス説明書
ページ先へ移動 of 12
OPER AT ING INSTRUCTIONS FINISHER 4300 Model No. BA-FS43 Banner American Products, Inc. abcoffice 800-658-8788 www.abcoffice.com.
Table of Contents I. For Your Safety ............................................... 2 II. Electrical Safeguards ....................................... 2-3 III. Specifications .................................................. 3 IV. Set-up ..........
Finisher 4300 (BA-FS43) SPEED CONTROL TOP BOTTOM TEMPERATURE CONTROL BOTTOM HEAT SHOE TEMPERATURE CONTROL TOP HEAT SHOE 1 0 1 0 FORWARD REVERSE FANS MOTOR HEAT HEATED ROLLERS Control Panel Brake Nut C.
u Do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. u Read all safety messages located in this instruction manual and on the laminator very care- fully.
u Do not operate the laminator with a damaged power supply cord or plug. u Replace fuses only with same type rated 30A, 240V and 1A, 250V fuses. Contact your dealer for replacement fuses. u There are four (4) EMERGENCY STOP buttons on your Finisher 4300, two in the front and two in the back.
Threading the Film (Figures 1&2) 1. Feed the film from the top roll behind the upper idler roller rod and lay it over both heat shoes. Be sure that the adhesive side of the film is facing out and the non-adhesive side is against the heat shoes. 2.
Slitters (Figure 4) : To install the slitters, place the Main Body Clamps into the Top Roller Guard where they will slide into the slots in the in the top edge of the guard located at each end of the guard. Before setting the slitters in place, ensure the machine is loaded with the proper laminating film.
VI. Pressure Sensitive Laminating... Note: You must have the Rewind Option for Pressure Sensitive Films in order to laminate with pressure sensitive material. 1. Load a roll of pressure sensitive film onto the upper mandrel so that it unwinds toward you from the bottom of the roll.
VIII. Mounting & Laminating... 1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions and the laminat- ing film is loaded correctly (See page 3 for film loading instructions). 2. Open the ROLLER RELEASE handle and select the MOUNT position on both sides of your laminator.
Cleaning Rubber Rollers: Excessive build-up of adhesive on the rollers may cause poor lamination quality and erratic film movement. Use the following procedure to remove any adhesive from the laminating rollers. 1. Turn the HEATED ROLLERS and TOP & BOTTOM SHOES OFF and allow the laminator to cool .
X. Trouble-shooting... Symptom Possible Cause Corrective Action LCDs do not show display No power to laminator Close panel breaker when heat switches are on. Blown fuse Disconnect power and replace fuse Film is not bonding to the print Laminator not set to optimal Adjust temperature slightly laminating temperature upward.
XI. Laminating & Mounting Do’s and Don’ts... Read the instruction manual before operating your laminator. Always run test samples before laminating valuable items. Feed the print through slowly and evenly, smoothing it as it is pulled into the laminator.
デバイスABC Office BA-FS43の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ABC Office BA-FS43をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはABC Office BA-FS43の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ABC Office BA-FS43の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ABC Office BA-FS43で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ABC Office BA-FS43を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はABC Office BA-FS43の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ABC Office BA-FS43に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちABC Office BA-FS43デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。