Life Fitnessメーカー8105の使用説明書/サービス説明書
ページ先へ移動 of 17
Part # 6787901 Revision: 06/18/98 1 ASSEMB LY INSTRUCTIONS 8105 SMITH PRESS.
2 IMPO RT ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8105 SMITH PRESS. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
PARTS LIST PART # 6712002 6711402 6711203 6708901 6711601 6711701 6710201 6710102 6710503 6710403 6787301 6709001 6709901 6709603 6675501 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 2 2 1 2 1 1 1 2 1 .
• CAREFULL Y lower one COUNTER WEIGHT (14) down into the LEFT UPRIGHT (9) & RIGHT UPRIGHT (10) until it bottoms out as shown in FIGURE 2. 4 FIGURE 2 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 2: .
5 FIGURE 3 STEP 3: • LOOSEL Y assemble the LOWER SUPPORT (3) and two PL ATE HOLDER (15) to the LEFT & RIGHT UPRIGHTS (9& 10) using four 1/2 X 4-1/2 ” BOLTS (16) and four 1/2 ” LOCK NUTS (21) as shown in FIGURE 3.
6 FIGURE 4 • SECUREL Y assemble four PL ATE HOLDERS (15) to the LEFT & RIGHT UPRIGHTS (9 & 10) using eight 1/2 X 4 ” BOL TS (17) , eight 1/2 ” W ASHERS (20), and eight 1/2 ” LOCK NUTS (21) as shown in FIGURE 4 .
7 STEP 5: • LOOSEL Y assemble two CHROME ANGLES (12) to the top of the LEFT & RIGHT UPRIGHTS (9 & 10) using four 1/2 X 4-1/ 2 ” BOLTS (16), and four 1/2 ” LOCK NUTS (21) as shown in FIGURE 5. (NOTE: M AKE SURE CABLE IS BETWEEN THE TWO BOL TS.
8 FIGURE 6 STEP 6: • LOOSELY assemble UPPER SUPPORT (11) to the LEFT & RIGHT UPRIGHTS (9 & 10) using two 1/2 X 4 ” BOLTS (17) two 1/2 ” WASHERS (20) and two 1/2 ” LOCK NUTS (21) as shown in FIGURE 6. (NOTE: MAKE SURE CABLE IS INSIDE OF THE 1/2” BOLT AS SHOWN IN DETAIL.
9 FIGURE 7 STEP 7: • SECURELY assemble the 4-1/2 ” PULLEYS (27) to the UPPER SUPPORT (11) using two 3/8 X 2 ” BOLTS (18) and two 3/8 ” LOCK NUTS (22) as shown in FIGURE 7.
10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 8 STEP 8: • Insert two 80 ” GUIDE RODS (13) through the BUSHINGS in the UPPER SUPPORT (11) and out through the top, then lower the GUIDE RODS (13) down into the BUSHING on the BASE of the UPRIGHTS (9 & 10) as shown in FIGURE 8.
11 STEP 9: • Slide one 1-1/2 ” THRUST BEARING (25), one RIGHT SAFETY HOOK (6), and one 1 ” SHAFT COLLAR (24) over the SAFETY STOP (2) as shown in FIGURE 9. FIGURE 9 FIGURE 10 • Slide one 1-1/2 ” THRUST BEARING (25), one LEFT SAFETY HOOK (5), and one 1 ” SHAFT COLLAR (24) over the SAFETY STOP (2) as shown in FIGURE 9.
12 STEP 12: FIGURE 11 FIGURE 12 • Slide one BEARING HOUSING (1), one 2 ” SHAFT COLLAR (23), and one 2-1/2 ” OD RUBBER BUMPER (29) over each SLEEVE ASSEMBLY (4) as shown in FIGURE 11. • Using a 1/4 ” Allen wrench, SECURELY tighten each set screw on the 2 ” SHAFT COLLARS (23).
13 FIGURE 13 STEP 13: • Lift up each GUIDE ROD (13) and insert them through each BEARING HOUSING (1) on the SMITH BAR ASSEMBLY (7) then seat GUIDE RODS (13) back into the BUSHINGS in the BASE of the UPRIGHTS (9 & 10). See FIGURE 13. 7 • Lift up each GUIDE ROD (13) and slide one 1 ” SHAFT COLLAR (24) over the bottom of each GUIDE ROD (13).
14 FIGURE 14 STEP 14: • Lift up on each GUIDE ROD (13) and slide the RIGHT & LEFT BAR STOP ASSEMBLIES (8) over the bottom of each GUIDE ROD (13) onto their respective sides then lock the HOOKS of the BAR STOPS (8) onto the CHROME ANGLES (12) then seat GUIDE RODS (13) back into the BUSHINGS in the BASE of the UPRIGHTS (9 & 10).
15 FIGURE 15 STEP 15: • Loosen each 1 ” SHAFT COLLAR (24) and slide each one up firmly against the BUSHINGS of the UPPER SUPPORT (11). See FIGURE 15. • Using a 3/16 ” Allen wrench, SECURELY tighten each set screw on the 1 ” SHAFT COLLARS (24).
16 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 16 STEP 16: • SECURELY assemble threaded end of CABLE ASSEMBLIES (26) into the BEARING HOUSINGS (1) using one 1/2 ” WASHER (20) on each side as shown in FIGURE 16. 26 8 20 • NOTE: Lubricate the GUIDE RODS (13) with a light oil or lubricant that is available at most hardware stores.
17 FIGURE 17 STEP 17: • MAKE SURE ALL CONNECTIONS ARE TIGHT! Thank you for purchasing the Life Fitness 8105 SMITH PRESS. If unsure of proper use of equipment, call your local Life Fitness distributor or call the Life Fitness customer service department at (800) 328-9714.
デバイスLife Fitness 8105の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness 8105をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness 8105の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness 8105の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness 8105で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness 8105を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness 8105の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness 8105に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness 8105デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
