Life Fitnessメーカー880の使用説明書/サービス説明書
ページ先へ移動 of 47
1 880 GYM SYSTEM 1 CLASS H PAR T # 7183101 REV . C V ersion: 880102 Revision: 1/29/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 880 Gym System. Please read these instructions thoroughly and keep them for future reference.
Minimum Required Usable S p ace Length = 98 inches (250 cm) 8’ 2” Width = 98 inches (250 cm) 8’ 2” Height = 84 inches (213.5 cm) 7” 1 Square = 1’ X 1’ 4 Length = 98 inches (250 cm) 8’ .
P AR TS LIST PA R T # 7139708 7139808 69947 21 7145002 6523401 7139908 6940808 7140108 7140208 7129508 7075808 7149308 7061608 7061308 7061808 7076208 7140302 7140402 6549301 7012102 6773802 6995708 7.
P AR TS LIST 6 PA R T # 3102917 3102937 310291 1 3102963 7128202 7128203 3232101 3231501 3231601 3232001 6533501 7149501 7245601 3221703 KEY 95 96 97 98 99 100 101 102 103 104 105 106 107 108 QTY 1 1 .
FIGURE 1 7 STEP 1: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y assemble the REAR UPRIGHT (6) to the BASE FRAME (9) using two 3/8 X 3-3/4” BOL TS (93), two 3/8 X 4” BOL TS (94), six 3/8” W ASHERS (80) and four 3/8” LOCK NUTS (82) as shown in FIGURE 1.
FIGURE 2 STEP 2: • LOOSEL Y assemble two BASE PLA TES (11) to the REAR UPRIGHT (6) using two 3/8 X 3-3/4” BOL TS (93) and two 3/8” LOCK NUTS (82).
9 FIGURE 3 STEP 3: • Assemble the RIGHT PEC ARM (13) and LEFT PEC ARM (14) to the 16-1/4” TUBE (12) and PEC PLA TE (15) using two 1/2 X 6” BOL TS (97), two 1/2” W ASHERS (81), four 3/4” FLANGE BEARINGS (53), two 3/4” X 3-5/16” SHAFTS (100) and two 1/2” LOW HEIGHT LOCK NUTS (85) as shown in FIGURE 3.
10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 4: • SECUREL Y assemble the PEC PLA TE (15) and the 16-1/4” TUBE (12) to the REAR UPRIGHT (6) using two 3/8 X 2-3/4” BOL TS (90) and two 3/8” LOCK NUTS (82) as shown in FIGURE 4.
FIGURE 5 11 STEP 5: 1 3/8 X 3-3/4” 93 11 15 82 • SECUREL Y assemble the PEC PLA TE (15) and the BASE PLA TES (11) to the FRAME (1) using one 3/8 X 3-3/4” BOL T (93), one 3/8 X 4” BOL T (94) and two 3/8” LOCK NUTS (82) as shown in FIGURE 5.
12 STEP 6: FIGURE 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Repeat the previous steps to assemble the RIGHT PEC HANDLE (17) and the RIGHT PEC ARM (13) as shown in FIGURE 6.
13 FIGURE 8 STEP 8: FIGURE 7 • Insert two WEIGHT PLA TE BUSHINGS (71) into each of the fifteen WEIGHT PLA TES (115) as shown in FIGURE 7. STEP 7: • Slide the WEIGHT PLA TE SHAFT (75) thru the hole in the HEAD PLA TE (51), and lock in place using one E-RING (76) as shown in FIGURE 8.
FIGURE 9 STEP 9: 14 • Insert two GUIDE RODS (5) into the BASE FRAME (9) as shown on FIGURE 4. (NOTE: If the 880 SHROUD OPTION was purchased, place the GUIDE RODS (5) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the BASE FRAME (9) as shown in FIGURE 9.
FIGURE 10 STEP 10: 15 • Swing the GUIDE RODS (5) into the guide rod bushings in the BOOM BRACKET (8) as shown in FIGURE 10. • LOOSEL Y assemble the BOOM BRACKET (8) and the BOOM PLA TE (10) to the REAR UPRIGHT (6) and the FRAME (1) using three 3/8 X 3-3/4” BOL TS (93) and three 3/8” LOCK NUTS (82).
16 STEP 1 1: • SECUREL Y assemble one PEC ST A TION P AD (3) to the SEA T ADJUST (4) using two 3/8 X 1-3/4” BOL TS (88) and two 3/8” W ASHERS (80).
17 FIGURE 13 STEP 13: • Insert two 1/2” FLANGE BEARINGS (54) into the the LEG PEDEST AL (2) as shown in FIGURE 13. • Assemble the LEG PEDEST AL (2) to the FRAME (1) using two RH CAPS (64), one 1/2 X 4” BOL T (95), two 1/2” RH W ASHERS (65), and one 1/2” LOW HEIGHT LOCK NUT (85).
• Assemble two ROLLER P ADS (1 17) to the LEG PEDEST AL (2) using one 3/4 X 17” TUBE (19) and two 3/4” ST ARLOCK COLLARS (60) as shown in FIGURE 15. • Assemble two ROLLER P ADS (1 17) to the SEA T ADJUST (4) using one 3/4 X 17” TUBE (19), two PLASTIC W ASHERS (63) and two 3/4” ST ARLOCK COLLARS (60) as shown in FIGURE 15.
FIGURE 17 19 STEP 18: FIGURE 18 STEP 17: • SECUREL Y assemble the FOOT PLA TE (36) to the PRESS FRAME (32) using two 3/8 X 4” BOL TS (94) and two 3/8” LOCK NUTS (82) as shown in FIGURE 17. 82 32 36 3/8 X 4” 94 • Assemble two SPRING PINS (78) to the RIGHT and LEFT SQUA T ARMS (41 & 42) as shown in FIGURE 18.
20 FIGURE 19 STEP 20: FIGURE 20 STEP 19: • Insert two 3/4” FLANGE BEARINGS (53) and one 3/4” X 6” SHAFT (99) into the tube on the PRESS FRAME (32) as shown. 54 33 32 99 53 32 33 84 35 81 1/2 X 1 1” 98 • Insert two 1/2” FLANGE BEARINGS (54) into the PRESS EXTERIOR ADJUST (33) as shown in FIGURE 19.
FIGURE 21 21 STEP 21: • SECUREL Y assemble the PRESS ARM (38) to the PRESS PIVOT (35) using two 3/8 X 3” BOL TS (91) four 3/8” W ASHERS (80) and two 3/8” LOCK NUTS (82) as shown in FIGURE 21.
FIGURE 22 22 STEP 22: • Apply four P ARAGLIDES (73) to the OUTSIDE of the PRESS INTERIOR ADJUST (34) as shown in FIGURE 22. • CAREFULL Y insert the PRESS INTERIOR ADJUST (34) into the EXTERIOR PRESS ADJUST (33) as shown in FIGURE 22.
FIGURE 23 23 STEP 23: PUSH-PULL CABLE • Assemble the PUSH-PULL CABLE to the PRESS ADJUST HANDLE (106). Insert the small round barrel on the PUSH-PULL CABLE into the groove of the PRESS ADJUST HANDLE (106) as shown in FIGURE 23.
FIGURE 24 24 STEP 24: 33 11 3 11 2 • SECUREL Y assemble the SPRING PIN ASSEMBL Y of the PUSH/PULL CABLE to the spring pin barrel on the EXTERIOR PRESS ADJUST (33).
FIGURE 25 25 STEP 25: 33 34 • SECUREL Y assemble one 1/4” X 1-1/2” SOCKET HEAD CAP SCREW (102) thru the EXTERIOR PRESS ADJUST (33) and into the small threaded hole on the INTERIOR PRESS ADJUST (34) as shown in FIGURE 25.
26 FIGURE 26 STEP 27: FIGURE 27 STEP 26: • Assemble two FLOOR ROLLER WHEELS (74) to the BENCH FOOT (24) using two 1/2” X 1-1/2” CLEVIS PINS (104) and two 1/2” EXTERNAL RET AINING RING (103) as shown in FIGURE 26. • Assemble one U-PIN (1 10) to the BENCH SEA T ADJUST (28) using one 1/2” EXTERNAL RET AINING RING (103).
27 FIGURE 28 STEP 29: FIGURE 29 STEP 28: • SECUREL Y assemble the BENCH FOOT (24) to the BENCH FRAME (23) and the ROCKER PIVOT (25) using two 3/8 X 2-3/4” BOL TS (90), two 3/8” W ASHERS (80) and two 3/8” LOCK NUTS (82) as shown in FIGURE 28.
28 FIGURE 30 STEP 31: FIGURE 31 STEP 30: • Assemble the BACK P AD SUPPOR T (26) to the BENCH ROCKER (27) using two 1/2 X 6” BOL TS (97) and two 1/2” LOW HEIGHT LOCK NUTS (85). (Note: Tighten this connection enough to remove excess play yet allow the BENCH ROCKER to rotate fr eely .
29 STEP 32: FIGURE 32 • T o assemble the BENCH to the BENCH PRESS FRAME, lift up on the tube on the BENCH and tilt the BENCH on the FLOOR ROLLERS, inserting the BENCH into the BENCH PRESS FRAME as shown in FIGURE 32.
30 STEP 33: FIGURE 33 • Assemble two 3-1/2” PULLEYS (44) to the BOOM BRACKET (8) using two 3/8 X 1-3/4” BOL TS (88) and two 3/8” LOW HEIGHT LOCK NUTS (83) as shown in FIGURE 33. • Screw the long threaded end of the WEIGHT ST ACK CABLE (48) into the end of the HEAD PLA TE (51) .
31 STEP 35: FIGURE 35 • Route the WEIGHT ST ACK CABLE (48) around one 4-1/2” PULLEY (43) and assemble the PULLEY to the BOOM BRACKET (8) using one 3/8 X 3-3/4” BOL T (93), two 3/8 X 1” SP ACERS (57), and one 3/8” LOCK NUT (82). See FIGURE 35.
STEP 37: FIGURE 37 • Route the LA T CABLE (49) around one 3-1/2” PULLEY (44) and assemble two PULLEY PLA TES (7) to the 3-1/2” PULLEY (44) using one 3/8 X 1-3/4” BOL T (88) and one 3/8” LOCK NUT (82).
STEP 38: FIGURE 38 82 49 93 3/8 X 3-3/4” 11 8 8 33 • Securely assemble the LA T CABLE (49) to the THREADED HOUSING (1 18) then assemble the THREADED HOUSING (1 18) to the BOOM BRACKET (8) using one 3/8 X 3-3/4” BOL T (93), two 3/8 X 1” SP ACERS (57) and one 3/8” LOCK NUT (82) as shown in FIGURE 38.
STEP 40: 34 • Route the PRESS/LEG CABLE (47) under one 4-1/2” V -GROOVE PULLEY (45) and assemble the 4-1/2” V -GROOVE PULLEY (45) to the vertical bracket on the PRESS FRAME (32) using 3/8 X 2-3/4” BOL T (90) and one 3/8” LOW HEIGHT LOCK NUT (83).
STEP 42: FIGURE 41 3/8 X 1-3/4” 88 3/8 X 2-1/2” 89 32 34 • Assemble two 1” SQ. GLIDES (68) to the PRESS FRAME (32) and two 1” SQ. GLIDES (68) to the inside of the PRESS ADJUST BRACKETS (37) at the point where the PRESS ADJUST BRACKETS come into contact with the PRESS FRAME (32) as shown in FIGURE 42.
36 STEP 44: FIGURE 44 • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble the 3-1/2” PULLEY (44) to the PULLEY PLA TES (7) using one 3/8 X 1-3/4” BOL T (88) and one 3/8” LOCK NUT (82).
37 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 46 44 STEP 46: 83 22 3/8 X 6” 121 105 57 47 • Assemble two BOOM PULLEY PLA TES (22), three 3-1/2” PULLEYS (44) and two CABLE RET AINING CLIPS (105) to the BASE PLA TES (11) using one 3/8 X 6” BOL T (121), two 3/8 X 1” SP ACERS (57) and one 3/8” LOW HEIGHT LOCK NUT (83).
38 STEP 47: FIGURE 47 • Route the PRESS/LEG CABLE (47) around one 3-1/2” PULLEY (44) and assemble the 3-1/2” PULLEY (44) to the PULLEY PLA TES (7) using one 3/8 X 1-3/4” BOL T (88) and one 3/8” LOCK NUT (82).
39 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 49: FIGURE 49 • Route the threaded end of the PRESS/LEG CABLE (47) thru FRAME (1) and assemble the swivel end of PRESS/LEG CABLE (47) to the LEG PEDEST AL (2) using one 3/8 X 1-3/4” BOL T (88) and one 3/8” LOW HEIGHT LOCK NUT (83).
STEP 51: FIGURE 51 44 57 13 50 16 92 3/8 X 3-1/4” 88 3/8 X 1-3/4” 40 • Route the PEC CABLE (50) around one 4-1/2” PULLEY (43) and assemble the 4-1/2” PULLEY (43) to the FLOA TING PULLEY BRACKET (16) using one 3/8 X 1-3/4” BOL T (88) and one 3/8” LOCK NUT (82).
0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 52: FIGURE 52 44 57 14 50 92 3/8 X 3-1/4” 41 • Securely assemble the PEC CABLE (50) to the LEFT PEC ARM (14) as shown in FIGURE 52.
42 STEP 53: FIGURE 53 • SECUREL Y tighten all loose frame connections as shown in FIGURE 53! TIGHTEN! TIGHTEN! TIGHTEN! • Slide the SHAFT COLLARS (59) to the top of the GUIDE RODS (5) and tighten set screws as shown in FIGURE 53.
43 STEP 54: FIGURE 54 • Assemble the LOW ROW BAR (46) to the PRESS/LEG CABLE using two SNAP LINKS (52) and one 12-LINK CHAIN (61) as shown in FIGURE 54. The ANKLE STRAP (72) and AB CRUNCH STRAP (70) can also be used. • Assemble the LA T BAR (21) to the LA T CABLE using one SNAP LINK (52) as shown in FIGURE 54.
44 FIGURE 55 ADJUSTMENT • Adjustments can be made in the above locations to set the correct amount of tension in the cables. STEP 55: 51 16 • If upon completion of assembly , the HEAD PLA TE (51) .
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 45 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
46 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES Life Fitness Atlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 Life Fitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 Life Fitness (UK) Ltd.
デバイスLife Fitness 880の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Life Fitness 880をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLife Fitness 880の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Life Fitness 880の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Life Fitness 880で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Life Fitness 880を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLife Fitness 880の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Life Fitness 880に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLife Fitness 880デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
