Lincoln Electricメーカー2011 MKXの使用説明書/サービス説明書
ページ先へ移動 of 367
Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Message center 18 Entertainment Systems 35 MyLincoln T ouch™ system 35 Climate Controls 36 Automatic temperature control .
Seating and Safety Restraints 1 16 Seating 116 Safety restraints 129 Airbags 143 Child restraints 158 Tires, Wheels and Loading 176 T ire information 178 T ire inflation 180 T ire Pressure Monitoring .
Maintenance and Specifications 294 Engine compartment 296 Engine oil 298 Battery 301 Engine coolant 304 Fuel information 309 Air filter(s) 324 Part numbers 328 Maintenance product specifications and c.
CONGRATULATIONS Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.
Special instructions For your added safety , your vehicle is fitted with sophisticated electronic controls. W ARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter . Failure to follow the specific warnings and instructions could result in personal injury .
authorized service facilities, and that the diagnostic information may be used for any purpose. See your SYNC 威 supplement for more information. Event Data Recording This vehicle is equipped with an event data recorder (EDR).
T o read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer , other parties, such as law enforcement, that have such special equipment, can read the information if they have access to the vehicle or the EDR.
CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Lower Anchor Child Seat.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant T emper.
W ARNING LIGHTS AND CHIMES Instrument cluster with standard measure shown; metric similar W arning lights can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions.
Solid illumination after the engine is started indicates the on-board diagnostics system (OBD-II) has detected a malfunction. Refer to On-board diagnostics (OBD-II) in the Maintenance and Specifications chapter . If the light is blinking, engine misfire is occurring which could damage your catalytic converter .
Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected. Contact your authorized dealer as soon as possible. Normal braking is still functional unless the brake warning light also is illuminated.
AdvanceT rac 威 off light: Illuminates when AdvanceT rac 威 /traction control has been disabled by the driver . Refer to the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains on at start up or while driving, the tire pressure should be checked.
Door ajar (R TT): Displays when the ignition is on and any door is open. T ailgate ajar (R TT): Displays when the ignition is on and the trunk is open. Low washer fluid (R TT): Illuminates when the windshield washer fluid is low . T urn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.
Grade assist (R TT): Illuminates when the grade assist is turned on. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’ s door is opened. Parking brake on chime: Sounds when the parking brake is left on and the vehicle is driven.
MESSAGE CENTER W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is the safe operation of the vehicle.
Press the OK button to select highlighted options and confirm choices/messages. Main menu From the main menu screen you can choose the following: • Display Mode • T r i p1&2 • Fuel Economy • Settings • Information Scroll up/down to highlight one of the options, then press the right arrow key or OK to enter into that menu option.
Full analog tachometer + Fuel gauge Full analog tachometer + Fuel gauge + Engine coolant temperature gauge Intelligent all-wheel drive (A WD) (if equipped) + fuel gauge Shown with vertical bar tachometer enabled Select-Shift Automatic™ transmission (SST) Select-Shift tnsmission allows you to manually shift gears.
The selected gear will be displayed at the bottom of the vertical bar tachometer (if selected). The selected gear will be displayed within the full analog tachometer (if selected). T r i p1&2 Press the right arrow on the left steering wheel mounted button when t r i p1&2i ss e l e c t e d .
• A verage fuel economy — shows the average fuel economy for a given trip. • Estimated amount of fuel consumed — shows the amount of fuel used for a given trip. • Elapsed trip time — timer stops when the vehicle is turned off and restarts when the vehicle is restarted.
Fuel Economy Press the right arrow on the left steering wheel mounted button when fuel economy is selected. The boxes in the upper right corner of the screen indicate that there are multiple screens that you can navigate through. Each press of the right arrow will navigate to the next screen until the last screen is reached.
T o determine your average highway fuel economy , do the following: 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average.
V ehicle Autolamp Delay Off, 10 / 20 (default setting) / 30 / 60 / 90 / 120 / 180 seconds Easy Entry/Exit On (default on key cycle) / Off Fuel DTE Calculation Normal, T owing Long T erm Econ Hold OK to Reset.
*MyKey Create MyKey Press and hold OK to create MyKey T raction Control Always On / User Selectable Speed W arning Off, 65 mph (105 km/h), 55 mph (89 km/h), 45 mph (72 km/h) Max Speed Set to 80 MPH (130 km/h) / Off V olume Limiter On / Off Clear MyKeys Hold OK to Clear MyKeys *Some MyKey items will only appear if a MyKey is set.
System Check* Oil Life W ash Fluid Doors Liftgate B lind spot Cross T raffic Brakes Fuel (distance to empty) *Some items will only display during a system check if a problem has been detected.
LIFTGA TE AJAR — Displayed when the liftgate is not completely closed. P ASSENGER DOOR AJAR — Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. RIGHT REAR DOOR AJAR — Displayed when the rear right door is not completely closed.
engine oil in the Maintenance and Specifications chapter . If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. OIL CHANGE REQUIRED — Displayed when the oil life left reaches 0%. W ASHER FLUID LEVEL LOW — Indicates the washer fluid reservoir is less than one quarter full.
message after driving a short distance with the road tire re-installed or after the system is allowed to cool. CHECK A WD — Displayed in conjunction with the Throttle Control/T ransmission/A WD light when the A WD system is not operating properly .
COULD NOT PROGRAM KEY — Displayed when an attempt is made to program a spare key using two existing MyKeys. Refer to MyKey™ in the Locks and Security chapter for more information. KEY PROGRAMMED 3 KEYS TOT AL — Displayed during spare key programming, when a third Intelligent Access Key is programmed to the system.
ST AR TING SYSTEM F AUL T — This message is displayed when there is a problem with your vehicle’ s starting security system; your vehicle will not be able to start.
BLINDSPOT NOT A V AILABLE SENSOR BLOCKED SEE MANUAL(if equipped) — Displayed when the blind spot information system/cross traffic alert system sensors are blocked. See Blind Spot Information System (BLIS 威 ) with Cross T raffic Alert in the Driving chapter .
TO STOP ALARM ST AR T VEHICLE — Displayed when the perimeter alarm system is armed and the vehicle is entered using the key on the driver’ s side door . In order to prevent the perimeter alarm system from triggering, the ignition must be turned to start or on before the 12 second chime expires.
MYLINCOLN T OUCH™ W ARNING: Driving while distracted can result in loss of vehicle control, accident and injury . Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Y our primary responsibility is the safe operation of the vehicle.
DUAL AUTOMATIC T EMPERATURE CONTROL (DA TC) SYSTEM WITH MYT EMP Note: Y our climate control system is touch sensitive. Y ou need only lightly touch the control graphic to activate the feature. Note: Y our vehicle is also equipped with touchscreen climate control features.
economical and efficient. Recirculated air may also help reduce undesirable odors from entering the vehicle. T ouch MAX A/C again for normal A/C operation. 4. A/C control: T ouch to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency .
Operating tips • T o reduce fog build-up on the windshield during humid weather , select (defrost) or (floor/defrost). • T o reduce humidity build-up inside the vehicle, do not drive with the system off or with (recirculated air) engaged and A/C off.
T ouchscreen features Press the lower right corner on the touchscreen to access these features. 1. (Power): Press to activate/deactivate the climate control system. When the system is off, outside air is prevented from entering the vehicle through the vents.
5. MAX A/C: Press to distribute recirculated air through the instrument panel vents to cool the vehicle. This is more economical and efficient than normal A/C mode. Recirculated air may also help reduce undesirable odors from entering the vehicle. Press again for normal A/C operation.
• Press to control the heated seat. Refer to Heated and cooled seats in the Seat and Safety Restraints chapter . • Press to control the cooled seat. Refer to Heated and cooled seats in the Seat and Safety Restraints chapter . • Press and hold MyT emp to select a temperature you would like the vehicle to remember and maintain for you.
*Note: If you have said “T emperature”, you can then say any of the following commands: • High • Low • <15.5–29.5> degrees • <60–85> degrees For more information on your touchscreen system, refer to the MyFord T ouch™ / MyLincoln T ouch™ supplement.
Automatic climate control For hot weather conditions: • The interior cabin will be cooled to 72°F (22°C). • The cooled seats (if equipped) will be set to high. For cold weather conditions: • The interior cabin will be heated to 72°F (22°C). • The heated seats (if equipped) will be set to high.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Adaptive headlamps (if equipped) The headlamp beams move in the same direction as the steering wheel which provides more visibility when driving around curves.
Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. • T o turn autolamps on, rotate the control to . • T o turn autolamps off, rotate the control from the autolamp position.
Fog lamp control The fog lamps can be turned on when the headlamp control is in the , ,o r positions and the high beams are not turned on. Press the top of the control, located on the instrument panel, to activate the fog lamps. The fog lamp indicator will illuminate when the fog lamps are on.
W ARNING: Always remember to turn on your headlamps at dusk or during inclement weather . The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2.
4. Locate the vertical adjuster on each headlamp. Using a Phillips #2 screwdriver , turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up). The horizontal edge of the brighter light should touch the horizontal reference line.
INTERIOR LAMPS Front row map lamps (if equipped) T o turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened. • the dome lamp button on the instrument panel is activated. • the remote entry controls are pressed and the ignition is off.
BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold.
Function Number of Bulbs T rade Number * Rear sidemarker lamp N/A LED * Stop/tail/turn lamp N/A LED Backup lamp 2 921 License plate lamp 2 C5W * High-mount brake lamp N/A LED Fog lamp (if equipped) 2 .
4. T urn the bulb holder counterclockwise and remove it. 5. Disconnect the electrical connector . W ARNING: Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass.
2. At the wheel well, remove the fasteners from the splash shield, then pull the splash shield back to gain access to the bulbs. 3. Rotate the bulb socket counterclockwise and remove from the lamp assembly . 4. Carefully pull the bulb out of the socket.
Replacing backup lamp bulbs The backup lamp bulb is located in the lower portion of the tail lamp assembly . Follow the below steps to replace the bulb. Note: Y our vehicle is equipped with a tail/stop/turn/sidemarker lamp assembly containing integral multiple light emitting diodes (LED).
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the off position. 2. Remove the two screws and the license plate lamp assembly from the liftgate. 3. Carefully pull the bulb straight out from the lamp assembly . Install new bulb(s) in reverse order .
WINDSHIELD WIPERS W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.
W indshield washer: Press the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick press and hold: the wipers will swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds.
From either position, the control will automatically return to the 2 or O (off) position. Reverse wiper feature: The rear wiper will be automatically activated in an intermittent setting when shifting into R (Reverse) if the front wipers are activated.
Easy entry/exit feature When the ignition is turned off, the column will move to the full up and in position if this feature is activated through the message center . Refer to Message center in the Instrument Cluster chapter . When the ignition is turned on, the column will return to the previous setting.
ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamp. Slide-on-rod feature The visor will slide back and forth on the rod for increased sunlight coverage. Rotate the visor towards the side window and extend it rearward for additional sunlight coverage.
CENTER CONSOLE Y our vehicle may be equipped with a variety of console features. These include: 1. Cupholders 2. Utility compartment with in-bin power point and a removable coin holder tray (two grooves on tray slide onto tracks in main bin). 3. Rear power point W ARNING: Use only soft cups in the cupholder .
T o have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery . T o prevent the battery from being discharged: • do not use t.
T o operate one-touch up, pull the switch completely up to the second detent and release quickly . The window will close fully . Momentarily press the switch to any position to stop the window operation. Global open windows Press and hold to begin opening the two front windows and venting the panoramic roof (if equipped).
Window lock The window lock feature allows only the driver and front passenger to operate the power windows. T o lock out all the window controls (except for the driver and front passenger) press the right side of the control. Press the left side to restore the window controls.
EXTERIOR MIRRORS Power side view mirrors W ARNING: Do not adjust the mirror while the vehicle is in motion. T o adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror .
Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Blind spot mirrors (if equipped) Y our vehicle may be equipped with blind spot mirrors or a blind spot information system.
2. Accelerate to the desired speed. 3. Press SET upward and release. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill.
Turning of f speed control T o turn off the speed control, press OFF downward or turn off the ignition. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.
W ARNING: Do not use in poor visibility , specifically fog, rain, spray or snow . Using adaptive cruise control Note: It is the drivers responsibility to stay alert, drive safely and be in control of the vehicle at all times. The controls for using your cruise control are located on the steering wheel.
Following a vehicle W ARNING: When following a vehicle in front of you, the vehicle will not decelerate automatically to a stop, nor will the vehicle always decelerate quickly enough to avoid a collision without driver intervention. Always apply the brakes when necessary .
Setting the gap distance The distance between your vehicle and the vehicle in front of you can be decreased or increased by pressing the GAP control up or down. The selected gap will be displayed in the message center as shown by the bars in the graphic.
Changing the set speed There are three ways to change the set speed: • Accelerate or brake to the desired speed and press SET upward and release. • Increase or decrease the speed by holding SET upward or downward until the desired set speed is shown on the message center .
Detection issues The radar sensor has a limited field of vision. In some situations it may not detect vehicles at all or detect a vehicle later than expected. Detection issues can occur: • When driving on a different line than the vehicle in front. • W ith vehicles that edge into your lane.
• There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. In these cases ACC may brake late or unexpectedly .
Cause Action The surface of the radar in the grille is dirty or obstructed in some way Clean the grille surface in front of the radar or remove the object causing the obstruction The surface of the radar in the grille is clean but the message remains in the display W ait a short time.
STEERING WHEEL CONTROLS Audio control features SEEK: Press up or down to select the next/previous radio station preset, CD track or satellite radio channel (if equipped) preset depending on which media mode you are in. MEDIA: Press repeatedly to scroll through available audio modes.
• Phone • Redundant center stack display • Favorite contacts • Climate • On • Fan speed • T emperature PANORAMIC VISTA ROOF™ AND POWER SUNSHADES (IF EQUIPPED) The panoramic Vista Roof™ and power sunshade controls are located on the overhead console.
T o open power sunshades and panoramic V ista Roof™: Press and release the control to open the sunshade. The front and rear sunshades open simultaneously . Note: Vista Roof™ will only open after power sunshades are completely open. Power sunshades will only close after Vista Roof™ is completely closed.
HomeLink 姞 Wireless Control System (if equipped) The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink 威 button you wish to program (located on your visor) while keeping the indicator light in view .
Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink 威 to accept the signal from the hand-held transmitter .
Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. T o remove the floor mat, reverse the installation procedure.
Note: Cycling the ignition prior to completely latching the liftgate could result in damage to the liftgate and/or its power components. Make sure the liftgate is fully latched before operating the vehicle. Care should be exercised in starting the engine before the liftgate is fully closed (latched).
T o power open the liftgate with outside liftgate control button: 1. Unlock the liftgate with the transmitter or power door unlock control. If the intelligent access transmitter is within 3 feet (1 meter) of the liftgate, the liftgate will unlock when you press the liftgate release button.
Obstacle detection: The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system will reverse to full open when it detects an obstacle. A chime will sound three times when an obstacle is detected as the liftgate begins to reopen.
Manual liftgate operation The liftgate cargo area is only intended for cargo, not for passengers. T o open the liftgate, press the button located in the top of the liftgate pull cup handle to unlatch the liftgate, then pull on the handle. • Exercise care when opening or closing the liftgate in a garage or other enclosed area.
CARGO AREA FEATURES Cargo management system (if equipped) The cargo management system consists of storage compartments located in the floor of the rear cargo area. 1. T o open, lift the release handle and the lid. 2. T o close, lower the lid. Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area.
Utility hook The utility hook can be used to hang small items such as grocery bags, etc. Do not hang more than 10 lb (4.5 kg) on the hook. ROOF RACK SYSTEM (IF EQUIPPED) Loads should never be placed directly on the roof panel.
INTELLIGENT ACCESS KEY (IA KEY) Y our vehicle is equipped with two intelligent access keys which operate the power locks and the remote entry system. The IA key must be in the vehicle to activate the push button start system. The IA key also contains a removable mechanical key blade that can be used to unlock the driver door .
feature. When the MyKey™ feature is enabled the user can use system check in the message center to see how many MyKeys™ and admin keys are programmed to the vehicle, and see the total distance the vehicle has been driven with the MyKey™ active.
MyKey™ is successfully programmed. Make sure you label it so you can distinguish it from the admin keys. Note: T o program the optional settings go to Step 2 in the Programming MyKey™ optional settings section. If your vehicle is equipped with remote start, see the Using MyKey™ with remote start systems section.
Refer to Message center in the Instrument Cluster chapter for MyKey™ system warnings displays. Using MyKey™ with remote start systems MyKey™ is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please see your authorized dealer for a Ford-approved remote start system.
T roubleshooting Condition Potential Causes Can’t create a MyKey™ • Key in backup slot is the last remaining admin key (there always has to be at least one admin key). • Key in backup slot is a MyKey™. • Key is not in the backup slot. • SecuriLock 威 passive anti-theft system is disabled or in unlimited mode.
Condition Potential Causes I accidentally programmed all keys as MyKeys™ • V ehicle has a non Ford-approved remote start system that is recognized as an admin key . Refer to the Using MyKey™ with remote start systems section to reset all MyKeys™ as admin keys.
POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks The smart unlock feature is intended to prevent you from unintentionally locking your IA key inside your vehicle’ s passenger compartment or rear cargo area.
Autolock feature The autolock feature will lock all the doors when: • all the doors are closed, • the ignition on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h).
1. T urn the ignition on. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition off. 4. Press the power door unlock control on the door panel three times. 5. T urn the ignition back on. The horn will chirp one time to confirm programming mode has been entered and is active.
Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened. Deactivating/activating autounlock feature Y our vehicle comes with the autounlock f.
Keyless entry keypad autounlock enable/disable procedure 1. T urn the ignition off. 2. Close all the doors. 3. Enter factory–set 5–digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press and release the 7 • 8. While still holding the 3 • 4, press and release the 7 • 8a second time.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. The typical operating range for your transmitter is approximately 33 feet (10 meters).
Y our intelligent access system uses a radio frequency (RF) signal to communicate with your vehicle and authorize your vehicle to unlock when commanded (either by touching the inside of the driver or front passenger exterior door handle, the power liftgate button, or a button on the transmitter itself).
The battery saver feature will turn off the lamps 10 minutes after the ignition is turned off. T wo stage unlocking may be disabled or re-enabled by simultaneously pressing the and controls on the transmitter for four seconds (disabling two stage unlock allows all vehicle doors to unlock simultaneously).
If the liftgate stops mid-travel, it may have detected an obstacle. Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate. Normal operation can then be resumed. W ARNING: Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle.
2. W ithin three seconds press the . 3. Repeat this procedure for transmitter if desired. Memory profiles The memory feature also coordinates with user -created profile settings utilizing the infotainment touchscreen system (if equipped). See the Creating a user profile section in the MyLincoln T ouch™ supplement for more information.
Replacing lost intelligent access keys (IA keys) If you would like to have your IA keys reprogrammed because you lost one, or would like to buy additional transmitters you can either reprogram them yourself, or take all transmitters to your authorized dealer for reprogramming.
• If the dome lamps were turned on using the panel dimmer control, the battery saver will shut them off 10 minutes after the ignition has been turned off. • If the courtesy lamps were turned on because one of the vehicle doors or the trunk was opened, the battery saver will shut them off 10 minutes after the ignition has been turned off.
The remote start system will not work if: • The ignition is on. • The alarm system is triggered. • The feature has been disabled. • The hood is not closed. • T wo remote vehicle starts have already been attempted within the last hour . • The vehicle is not in P (Park).
The ignition must be turned on and then back off or allow one hour to pass before using remote start again. T urning the engine off after using remote start • Press one time. The parking lamps will turn off. Y ou may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running engine.
T ips: • Do not set a code that uses five of the same number . • Do not use five numbers in sequential order . • The factory set code will work even if you have set your own personal code. Erasing personal code 1. Enter the factory set 5–digit code.
SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless an intelligent access key programmed to your vehicle is used.
If your intelligent access key are lost or stolen and you don’t have an extra key , you will need to have your vehicle towed to an authorized dealer . The key codes need to be erased from your vehicle and new keys will need to be programmed. Replacing intelligent access keys can be very costly .
been programmed to your vehicle, you cannot program anymore and the message MAX # OF KEYS LEARNED will be displayed on the message center . 7. Remove intelligent access key from utility compartment pocket and press the or control on the newly programmed intelligent access keys to exit programming mode.
After locking the doors using any of the methods above, the turn signal lamps will flash once indicating that the perimeter alarm is in the pre-armed mode and will become fully armed in 20 seconds. Note: Pressing the power door unlock control within the 20-second, pre-armed mode will disarm the system.
FRONT SEATING W ARNING: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
T o adjust the head restraint, do the following: 1. Adjust the seatback to an upright driving/riding position. 2. Raise the head restraint by pulling up on the head restraint. 3. Lower the head restraint by pressing and holding the guide sleeve adjust/release button and pushing down on the head restraint.
T o remove the adjustable head restraint, do the following: 1. Pull up the head restraint until it reaches the highest adjustment position. 2. Simultaneously press and hold both the adjust/release button and the unlock/remove button, then pull up on the head restraint.
W ARNING: T o minimize the risk of neck injury in the event of a crash, head restraints must be installed properly . Adjusting the front power seat W ARNING: Never adjust the driver’ s seat or seatback when the vehicle is moving. W ARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Press the front or rear portion to tilt the seat. Press the control to move the seat forward, backward, up or down. Move the switch to recline the seatback forward or rearward. Using the power lumbar support The power lumbar control is located on the outboard side of the seat.
Heated and cooled seats Heated seats W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
If the engine falls below 350 RPMs while the cooled seats are on, the feature will turn itself off and will need to be reactivated. Climate controlled seats air filter replacement The climate controlled seat system includes air filters that must be replaced periodically .
T o install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Memory profiles The memory feature also coordinates with user -created profile settings utilizing the infotainment touchscreen system. See the Creating a user profile section in the MyLincoln T ouch™ supplement for more information.
W ARNING: T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. 2nd row manual folding seat T o fold down the rear seat, pull up on the lever on the outboard side of the seat cushion and let the seatback rotate downward into the load floor position.
Press and hold the control mechanism to lower the seatback. The top portion lowers the right (40%) seatback, and the bottom portion lowers the left (60%) seatback.
Seat-mounted armrest and cupholders Y our vehicle is equipped with a rear seat armrest. T o fold the armrest down, release the latch located on the seatback by pressing down and pulling forward. T o access the cup holders, lift up one of the slotted areas on the cover .
Rear heated seats (if equipped) W ARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater .
SAFETY RESTRAINTS Personal Safety System™ The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
longitudinal deceleration. The pretensioners are designed to activate in frontal and near -frontal collisions, and in rollovers and side collisions when the Safety Canopy 威 is activated. Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy .
W ARNING: Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off the front passenger airbag and passenger seat-mounted side airbag.
The Restraints Control Module (RCM) monitors its own internal circuits and the circuits for the airbag supplemental restraints, crash sensor(s), safety belt pretensioners, front safety belt buckle sensors, driver seat position sensor , and front passenger sensing system.
W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. W ARNING: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair .
2. T o unfasten, press the release button and remove the tongue from the buckle. Restraint of pregnant women W ARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips.
(8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. In addition, the retractor is designed to lock if the webbing is pulled out too quickly . If this occurs, let the belt retract slightly and pull webbing out again in a slow and controlled manner .
How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer . Use only extensions manufactured by the same supplier as the safety belt.
Second row comfort guide The second row outboard lap/shoulder belt is equipped with a belt comfort guide. This guide is attached to the head restraint and is stored in a pocket in the seatback. It is used to adjust the comfort of the shoulder belt for smaller occupants in the outboard second row seats.
Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the on position.
If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on... The Belt-Minder 威 feature will not activate.
The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers.
One-time disable If at any time the driver/front passenger quickly buckles then unbuckles the safety belt for that seating position, the Belt-Minder 威 is disabled for the current ignition cycle. The Belt-Minder 威 feature will enable during the same ignition cycle if the occupant buckles and remains buckled for approximately 30 seconds.
3. For the seating position being disabled, buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. • After Step 3, the safety belt warning light will be turned on for three seconds. 4. W ithin approximately seven seconds of the light turning off, buckle then unbuckle the safety belt.
Important supplemental restraint system precautions Airbags DO NOT inflate slowly or gently and the risk of injury from a deploying airbag is greatest close to the trim covering the airbag module.
W ARNING: Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury . W ARNING: Do not attempt to service, repair , or modify the airbag supplemental restraint system (SRS) or its fuses.
How does the safety belt pretensioner and airbag supplemental restraint system work? The safety belt pretensioner and airbag SRS are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates pretensioner activation and airbag inflation.
W ARNING: Several air bag system components get hot after inflation. Do not touch them after inflation. W ARNING: If the air bag has deployed, the air bag will not function again and must be replaced immediately . If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
The front passenger sensing system will disable (will not inflate) the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat. • the system determines that an infant is present in a rear -facing infant seat that is installed according to the manufacturer’ s instructions.
• When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the passenger airbag status indicator will illuminate the ON lamp and remain illuminated.
W ARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor .
If objects are lodged and/or cargo is interfering with the seat; please take the following steps to remove the obstruction: • Pull the vehicle over . • T urn the vehicle off. • Driver and/or adult passengers should check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.
If any of these things happen, even intermittently , have the supplemental restraint system serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision.
The side airbag system consists of the following: • An inflatable bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • The same warning light, electronic control and diagnostic unit as used for the front airbags.
W ARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Safety Canopy 姞 System W ARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy 威 . Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
How does the Safety Canopy 姞 System work? The design and development of the Safety Canopy System included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group.
The safety canopy is mounted to roof side-rail sheet metal, behind the headliner , above each row of seats. In certain lateral collisions or rollover events, the Safety Canopy System will be activated, regardless of which seats are occupied.
Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter . Routine maintenance of the airbag is not required.
Important child restraint precautions W ARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight.
Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommended restraint type Infants or tod- dlers Children weighing 40 lb (18 kg) or less (generally age four or younger) Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat).
Recommendations for attaching child safety restraints for children Re- straint T ype Child W eight Use any attachment method as indicated be- low by “X” LA TCH (lower an- chors and top tether an- .
W ARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury or death. W ARNING: Never use pillows, books, or towels to boost a child.
Follow all the safety restraint and airbag precautions that apply to adult passengers in your vehicle. If the child is the proper height, age, and weight (as specified by your child safety seat or boo.
position whenever possible. If all children cannot be seated and restrained properly in a rear seating position, properly restrain the largest child in the front seat. When installing a child safety seat with combination lap/shoulder belts: • Use the correct safety belt buckle for that seating position.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. 6. Allow the belt to retract to remove slack. The belt will click as it retracts to indicate it is in the automatic locking mode.
10. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.
Y our vehicle has LA TCH lower anchors for child seat installation at the seating positions marked with the child seat symbol. The LA TCH anchors are located at the rear section of the rear seat between the cushion and seat back, below the locator symbols on the seat back.
Use of inboard lower anchors from the outboard seating positions (center seating use) The lower anchors at the center of the second row rear seat are spaced 460 mm (18 inches) apart. The standardized spacing for LA TCH lower anchors is 280 mm (11 inches) center to center .
The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as described below . The tether anchors in your vehicle are located under the second row seat gap cover marked with tether anchor symbols (shown with title).
2. Locate the correct anchor behind the gap cover for the selected seating position. 3. Clip the tether strap to the anchor as shown. W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision.
both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster . Booster seats position a child so that vehicle lap/shoulder safety belts fit better .
T ypes of booster seats There are generally two types of belt-positioning booster seats: backless and high back. Always use booster seats in conjunction with the vehicle lap/shoulder belt. • Backless booster seats If your backless booster seat has a removable shield, remove the shield.
Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never place, or allow a child to place, the shoulder belt under a child’ s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a collision.
NOTICE TO CROSSOVER VEHICLE OWNERS Crossover vehicles handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road.
driving surfaces are relatively level, obstruction-free and otherwise similar to normal on-road driving conditions. Operating your vehicle under other than those conditions could subject the vehicle to excessive stress which might result in damage which is not covered under your warranty .
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING T ire Quality Grades apply to new pneumatic passenger car tires. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
W ARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’ s load carrying capability .
W ARNING: Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire.
Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive.
Improper or inadequate vehicle maintenance can cause tires to wear abnormally . Inspect all your tires, including the spare, frequently , and replace them if one or more of the following conditions ex.
U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.
W ARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again.
• Do not run over curbs or hit the tire against a curb when parking W ARNING: If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
• Front-wheel drive (FWD)/All-wheel drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below . Note: T ire Quality Grades do not apply to this type of tire.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label.
The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Low tire pressure warning light Possible cause Customer action required Flashing warning light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality .
SNOW TIRES AND CHAINS W ARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover , personal injury and death.
V EHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer , to keep your loaded vehicle weight within its design rating capability , with or without a trailer . Properly loading your vehicle will provide maximum return of vehicle design performance.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door .
• Example only: W ARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage.
Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 kg. Y ou will need to reduce the load weight by at least 240 lb. (104 kg). If you remove 3-100 lb. (45 kg) cement bags, then the load calculation would be: 1,400 - (2 x 220) - (9 x 100) = 1,400 - 440 - 900 = 60 lb.
For load specification terms found on the label, refer to V ehicle loading - with and without a trailer in this chapter . Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Powertrain Maximum GCWR - lb (kg) Maximum T railer W eight - lb (kg) 3.
Hitches Do not use hitches that clamp onto the vehicle’ s bumper or attach to the axle. Y ou must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the hook retainers on the vehicle.
Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles (800 km) of trailer towing and don’t make full-throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades.
RECREATIONAL T OWING Follow these guidelines for your specific powertrain combination to tow your vehicle for personal travel (such as behind a motor home or a truck). Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle.
STARTING Ignition modes 1. Off — This position shuts the engine and all electrical accessories off. Press and release the ST ART/STOP button without applying the brake pedal when your vehicle is in accessory or on modes or when the engine is running.
W ARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.
• Make sure the gearshift lever is in P (Park). Push button start system Y our vehicle is equipped with the push button start system. Y ou can start your vehicle by pressing the start button in combination with the brake pedal rather than using a key .
when you press the ST ART/STOP button, it may be necessary to move your IA key to another area within the vehicle. The IA key may not be detected near the roof (between the driver or passenger sunvisor and the roof, or in the overhead console area) or in the extreme corners of the rear package tray , near your audio speakers.
Absence of the Intelligent Access key: Once the vehicle has started, the vehicle will remain running until being turned off by the ST ART/STOP button, even if the IA key is no longer found in the vehicle.
W ARNING: T o reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater , follow these re.
How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. T o clean them, use a dry cloth. Depending on the type of factory installed equipment, your engine block heater will use .4 to 1.0 kilowatt-hours of energy per hour of use.
Brake assist The brake assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and uses the ABS system to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brake pedal is pressed or ABS is engaged.
W ARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). T urn the ignition to the lock position and remove the key whenever you leave the vehicle. For vehicles with the push button start system, remove the IA key whenever you leave the vehicle.
W ARNING: Remember that even advanced technology cannot defy the laws of physics. It’ s always possible to lose control of a vehicle due to inappropriate driver input for the conditions. Aggressive driving on any road condition can cause you to lose control of your vehicle increasing the risk of personal injury or property damage.
When AdvanceT rac 威 with RSC 威 performs a normal system self-check, some drivers may notice a slight movement of the brake, and/or a rumble, grunting, or grinding noise after startup and when driving off.
Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’ s directional stability during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway .
Switching off AdvanceT rac 威 with RSC 威 If the vehicle is stuck in snow , mud or sand, and seems to lose engine power , switching off certain features of the AdvanceT rac 威 with RSC 威 system may be beneficial because the wheels are allowed to spin.
T RAILER SWAY CONTROL When properly equipped, trailer sway control will use the vehicle’ s AdvanceT rac 威 with RSC 威 system to detect and help reduce trailer sway by applying brake force at individual wheels and, if necessary , by reducing engine power .
STEERING T o help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering fluid level (below the MIN mark on the reservoir).
If the fuse is not blown and the brake lamps are working properly , the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake, turn the ignition key to the off position, and remove the key . 2. Using a screwdriver (or similar tool), carefully pry off and remove the BSI access panel.
W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . AUTOMATIC TRANSMISSION OPERATION Automatic transmission adaptive learning Y our transmission is equipped with an adaptive learning strategy found in the vehicle computer .
N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy . T ransmission operates in gears one through six.
Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph.
Using hill start assist Hill start assist is activated automatically when the vehicle is stopped on a slope greater than five degrees. Hill start assist operates with the vehicle facing downhill if reverse gear is selected. W ARNING: Y ou must remain in the vehicle once you have activated hill start assist.
REVERSE SENSING SYSTEM The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds less than 3 mph (5 km/h). The system is not effective at speeds above 3 mph (5 km/h) and may not detect certain angular or moving objects.
The RSS detects obstacles up to six feet (two meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear video camera system, located on the liftgate, provides a video image of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle. T o use the rear video camera system, place the transmission in R (Reverse).
Objects are getting closer to your vehicle as they move from the green zone (4) to the yellow (3) or red zones (2). Use the side mirrors and rearview mirror to get better coverage on both sides and rear of the vehicle.
When manual zoom is enabled, only the centerline will be shown. Rear camera delay After shifting out of R (Reverse) and into any gear other than P (Park), the image will remain until the vehicle speed reaches five mph (8 km/h). This will only occur if the rear camera delay feature is on, or until any radio button is selected.
Note: If the camera system image is not clear or seems distorted, it may be covered with water droplets, snow , mud or any other substance. If this occurs, clean the camera lens before using the camera system.
Servicing • If the image comes on while the vehicle is not in R (Reverse), have the system inspected by your authorized dealer . • If the image is not clear , check if anything is covering the lens such as dirt, mud, ice, snow , etc. If the image is still not clear after cleaning, have your system inspected by your authorized dealer .
Operation The radar sensor detects vehicles ahead that are moving in the same direction as your vehicle. If the radar detects that your vehicle is rapidly closing on another vehicle a red warning light will illuminate and an audible warning chime will sound.
W ARNING: The collision warning system’ s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’ s brakes.
Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™ in the Locks and Security chapter for more information. Note: If collision warnings are perceived as being to.
W ARNING: Objects in the blind spot mirror are closer than they appear . BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS T RAFFIC ALERT (CT A) (IF EQUIPPED) The BLIS 威 is a convenience feature .
becomes active. Afterwards, the BLIS 威 remains active for all speeds including zero mph. BLIS 威 is also active if the transmission is placed in N (Neutral). If the transmission is shifted out of D (Drive) or N (Neutral) the system will enter the CT A mode (see CT A operation below).
BLIS 威 False Alerts Due to the nature of radar technology , there may be certain instances when the BLIS 威 will alert with no object present in the blind zone.
The CT A system detects vehicles approaching up to 45 feet (14 meters) away . Coverage decreases when vehicles and objects in close proximity block the CT A sensors (refer to figure for approximate zone coverage areas [sensor obstructed for vehicle on left] ).
CT A detection limitations: Due to the nature of radar technology , there may be certain instances where vehicles entering and exiting the blind spot zones may not be detected.
BLIS 威 and/or CT A fault operation If the BLIS 威 and/or CT A senses a fault on either the left or right sensor , the BLIS 威 alert indicator will go on and remain on and the message center will display BLIND SPOT SYSTEM F AUL T or CROSS TRAFFIC SYSTEM F AUL T .
The following table lists possible causes and actions for this message being displayed: The surface of the radar is dirty or obstructed in some way Clean the fascia area in front of the radar , either side, or remove obstruction.
All components of the A WD system are sealed for life and require no maintenance. Note: When an A WD system fault is present, the warning CHECK A WD will display in the message center . The A WD system is not functioning correctly and defaulted to front-wheel drive.
Under severe operating conditions, the A/C may cycle on and off to protect overheating of the engine. Basic operating principles • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. • Be extremely careful when driving on pavement made slippery by loose sand, water , gravel, snow or ice.
W ARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . W ARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander .
the system has cooled down, normal A WD function will return. When driving at slow speeds in deep sand under high outside temperatures, use L (Low) gear when possible. L (Low) gear operation will maximize the engine and transmission cooling capability .
Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly .” Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down.
A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks).
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Owner Guide portfolio in the glove compartment. In Canada, the card is found in the W arranty Guide in the glove compartment. U.S. Ford, Mercury and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. Canadian customers who require roadside assistance, call 1-800-665-2006.
W ARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury . Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 60A — — Blue Y ellow Y ellow 70A — — T an — Brown 80A — — Natural Black Black Passenger compartment fuse panel The fuse panel is located behind a trim panel on the left side of the driver’ s footwell near the parking brake.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Driver front smart window 2 15A Not used (spare) 3 30A Passenger front smart window 4 10A Demand lamps 5 20A Subwoofer 6 5A RF module 7 7.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 12 15A Interior lighting, Puddle lamps, Backlighting 13 15A Right turn/stop lamps and turn signals 14 15A Left turn/stop lamps and turn signals 1.
Fuse/Relay Location Fuse Amp Rating Protected Circuits 32 15A Moon roof, Power windows, Compass/auto-dimming rear view mirror 33 10A Not used (spare) 34 10A Reverse sensing system, Rearview camera, Bl.
W ARNING: T o reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter .
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 12 — Not used 13 — Starter relay 14 — Not used 15 — Fuel pump relay 16 — Not used 17 — Not used 18 40A** Blower motor.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 41 — Not used 42 30A** Passenger seat 43 30A** ABS valves 44 — Rear washer relay 45 5A* Rain sensor 46 — Not used 47 — No.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 71 — Not used 72 — Not used 73 — Not used 74 — Not used 75 — A/C clutch diode 76 — Not used 77 — TT park lamps rela.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use.
A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T -type mini-spare: This spare tire begins with the letter “T” for tire size and may have “T emporary Use Only” molded in the sidewall 2.
The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at .
Removing the spare tire and jack 1. Lift the carpeted load floor panel located in the rear of the vehicle. 2. Remove the spare tire cover (if equipped). 3. Remove the wing nut securing the spare tire by turning it counterclockwise. 4. Remove the washer .
W ARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. Note: Passengers should not remain in the vehicle when the vehicle is being jacked.
3. Align the slot on top of the jack with the sheet metal flange indicated by the jack locator triangle next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground. 4. Remove the lug nuts with the lug wrench.
If you are stowing a flat 22 inch tire and wheel assembly , temporarily remove the load floor , plastic stowage bins (if equipped), and the foam load floor supports to make space for the 22 inch tire and wheel assembly . Place the 22 inch tire & wheel assembly in the spare tire well with the valve stem facing down.
Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger .
Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery . 1. Remove the jumper cable from the ground metal surface.
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment.
If the vehicle is towed by other means or incorrectly , vehicle damage may occur . Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
GETTING THE SERVICES YOU NEED W arranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 T elephone 1-800-565-3673 (FORD) Online www .ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P .
In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent allowed by state law , before pursuing replacement or repurchase remedies provided by certain state laws.
LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss W arranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss W arranty Act, resort to BBB AUTO LINE is not required by those statutes.
Y ou can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 W ilson Boulevard, Suite 800 Arlington, V irginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673.
The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer . If the authorized dealer cannot help you, contact: Ford Middle East Customer Relationship Center P .O. Box 21470 Dubai, United Arab Emirates T elephone: +971 4 3326084 F AX: +971 4 3327299 Email: menacac@ford.
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft 威 Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.
• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo (CXC-66-A). • Cover the highlighted areas to prevent water damage when cleaning the engine.
may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. T o clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft 威 Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer .
• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.
• Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. W ARNING: Do not use cleaning solvents, bleach or dye on the vehicle’ s seatbelts, as these actions may weaken the belt webbing.
• Clean spills as quickly as possible. • T est any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather . • Do not spill coffee, ketchup, mustard, orange juice or oil-based products on the leather as they may permanently stain the leather .
FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Y our Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service.
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel near the steering column. 2. Go to the front of the vehicle and release the secondary hood latch that is located under the front center of the hood.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. T ransmission fluid dipstick 8. Engine oil dipstick 9.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
T o prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element. Changing rear window wiper blade The rear wiper arm is designed without a service position.
4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level dipstick. 6. W ipe the dipstick clean. Insert the dipstick fully , then remove it again. • If the oil level is within this range, the oil level is acceptable.
• If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer .
Use SAE 5W -20 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.
If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, make certain the battery cables are always tightly fastened to the battery terminals.
Because your vehicle’ s engine is electronically controlled by a computer , some control conditions are maintained by power from the battery . When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance.
ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water , which equates to a freeze point of -34°F (-36°C).
Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water . Add the mixture to the coolant reservoir , when the engine is cool, until the appropriate fill level is obtained.
a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. W ARNING: T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids.
V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
4. Check the coolant level and replenish if low . W ARNING: Fail-safe mode is for use during emergencies only . Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.
W ARNING: Gasoline may contain benzene, which is a cancer -causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling.
W ARNING: The flow of fuel through a fuel pump nozzle can produce static electricity , which can cause a fire if fuel is pumped into an ungrounded fuel container . Refueling W ARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries.
2. Open the fuel filler door . 3. Slowly insert the fuel filler nozzle fully into the fuel system and leave the nozzle fully inserted until you are done pumping. Pump fuel as normal. 4. After you are done pumping fuel, wait about five seconds before slowly removing the fuel filler nozzle.
Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may not be covered under warranty . Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87.
Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine.
1. After lifting the trunk cargo cover , locate the white plastic funnel. It is attached to the rear , lower edge of the spare tire compartment. 2. Slowly insert the funnel into the Easy Fuel™ system. 3. Fill the vehicle with fuel from the portable fuel container .
Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Maintenance product specifications and capacities section of this chapter . The advertised capacity is the amount of the indicated capacity and the empty reserve combined.
Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’ s fuel economy under current driving conditions.
• Use recommended engine oil. Refer to Maintenance product specifications and capacities in this chapter . • Perform all regularly scheduled maintenance items. Follow the recommended maintenance schedule and owner maintenance checks found in scheduled maintenance information.
If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability .
2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel fill inlet may not have been properly closed. See Easy Fuel™ “no cap” fuel system in this chapter . 4. Driving through deep water—the electrical system may be wet.
The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cyc.
BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary , refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube by turning it to the locked position.
Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary , add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by an authorized dealer .
housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing.
• Lubricate all hood, door and trunk lid hinges, and latches with a light grade oil. See the Cleaning chapter for more information. • Cover interior trim to prevent fading.
T ires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricate working parts and prevent corrosion.
MOTORCRAFT PART NUMBERS Component 3.7L V6 engine Engine air filter element F A-1884 Battery BXT -65 Oil filter FL-500-S Spark plugs SP-520 1 1 Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs.
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford Part Name Ford Part Number / Ford Specification Brake fluid Between MIN and MAX on reservoir Motorcraft 威 High Performance DOT 3 .
Item Capacity Ford Part Name Ford Part Number / Ford Specification Engine oil 1 5.5 quarts (5.2L) • Motorcraft 威 SAE 5W -20 Premium Synthetic Blend Motor Oil (US) • Motorcraft 威 SAE 5W -20 Ful.
Item Capacity Ford Part Name Ford Part Number / Ford Specification Power T ransfer Unit (PTU) fluid (A WD) 5 12 ounces (0.35L) Motorcraft 威 SAE 75W -140 Synthetic Rear Axle Lubricant XY -75W140-QL /.
ENGINE DATA Engine 3.7L V6 engine Cubic inches 226 Required fuel 87 octane Firing order 1–4–2–5–3–6 Ignition system Coil on plug Compression ratio 10.3:1 Spark plug gap 0.049–0.053 inch (1.25–1.35 mm) Engine drivebelt routing 1. Short drivebelt is on first pulley groove closest to engine.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint Devices and their location 3. Make, vehicle line, series, body type 4. Engine type 5.
LINCOLN CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Lincoln Custom Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer .
Peace of mind • Remote start • V ehicle tracking and recovery* • Keyless entry keypad • Protective seat covers* • Cargo security shade • W indshield wiper shaker* • Wheel locks • Bumper and hitch mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessory manufacturer’ s warranty .
FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford, Lincoln, and Mercury owners have discovered the powerful protection of Ford ESP . It is the only extended service plan backed by Ford Motor Company , and provides “peace of mind” protection beyond the New V ehicle Limited W arranty coverage.
Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract.
Ford Extended Service Plan 339 201 1 MKX (mkx) Owners Guide, 1st Printing USA (fus).
FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) Y ou can get more protection for your vehicle by purchasing a Ford Extended Service Plan (ESP). Ford ESP is the only service contract backed by Ford Motor Company .
GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for your vehicle. Carefully following this schedule helps protect against major repair expenses resulting from neglect or inadequate maintenance and may also help to increase the value of your vehicle when you sell or trade it.
If your message center is prematurely reset or becomes inoperative, you should perform the oil change interval at six months or 5,000 miles (8,000 km) from your last oil change. Y our vehicle is very sophisticated and built with multiple complex performance systems.
Genuine Ford parts and service When planning your maintenance services, consider your Ford and Lincoln Mercury dealership for all your vehicle’ s needs.
WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner checks and services Certain basic maintenance checks and inspections should be performed by the owner or a service technician at the intervals indicated. Service information and supporting specifications are provided in this Owner’ s Guide.
Multi-point inspection In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly . This can help identify potential issues and prevent major problems.
Scheduled Maintenance Guide 346 201 1 MKX (mkx) Owners Guide, 1st Printing USA (fus).
NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message center which determines the proper oil change service interval. Y ou should perform the engine oil change as indicated by the instrument cluster message center .
Oil Change Service Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • .
Perform the services noted in the following table at the specified time/mileage (km) period either within 3,000 miles (5,000 km) of the OIL CHANGE REQUIRED message appearing in the message center or when the time/mileage (km) reading indicates service is due.
Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
SPECIAL OPERATING CONDITIONS If you operate your Ford/Lincoln/Mercury vehicle primarily in one of the more demanding Special Operating Conditions listed below , you will need to have some items maintained more frequently .
Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery , taxi, patrol car or livery As required – Change engine oil and replace oil filter as indicated by message center and perform ser vices as listed in the Normal Scheduled Maintenance chart (except Fiesta).
Operating in dusty conditions such as unpaved or dusty roads Inspect frequently , service as required – Replace cabin air filter (if equipped). – Replace engine air filter . Every 5,000 miles (8,000 km) – Inspect the wheels and related components for abnormal noise, wear , looseness or drag.
Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&.
D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M.
EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic lubricant and light duty trucks equipped with Ford-design axles are lubricated for life.
COOLANT CHANGE RECORD Engine coolant ❑ 6 years or 100,000 miles (160,000 km) - change coolant (whichever comes first). ❑ After initial change - change coolant every 3 years or 50,000 miles (80,000 km).
Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE :M ILEAGE : D EALER V ALIDATION : P&A C OD.
A Accessory delay .......................... 65 Adaptive Cruise Control ............. 69 AdvanceT rac .............................. 218 Air cleaner filter ...............324, 328 Air conditioning .......................... 36 Airbag supplemental restraint system .
recommendations ................... 161 Child safety seats - booster seats ........................................... 172 Cleaning your vehicle engine compartment ..............287 instrument panel .................... 289 interior ..................
dipstick .................................... 298 filter , specifications ........ 300, 328 recommendations ................... 300 refill capacities ........................ 329 specifications .......................... 329 Event data recording .....
Instrument panel cleaning ................................... 289 cluster ........................................ 12 lighting up panel and interior ....................................... 47 Intelligent Access Key ................ 91 Intelligent Access with push button start .
Parts (see Motorcraft 威 parts) ........... 328 Passenger Occupant Classification Sensor ................. 130 Power distribution box (see Fuses) ............................... 260 Power door locks ........................ 97 Power liftgate ........
SecuriCode keyless entry system ........................................ 110 SecuriLock passive anti-theft system ........................................ 112 Servicing your vehicle .............. 294 SOS Post Crash Alert ............... 158 Spare tire (see Changing the T ire) .
W W arning lights (see Lights) ....... 12 W asher fluid .............................. 297 W ater , Driving through ............. 253 W indows power ......................................... 63 rear wiper/washer ..................... 59 W indshield washer fluid and wipers .
デバイスLincoln Electric 2011 MKXの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Lincoln Electric 2011 MKXをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric 2011 MKXの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric 2011 MKXの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric 2011 MKXで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric 2011 MKXを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric 2011 MKXの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric 2011 MKXに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric 2011 MKXデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
