Lincoln Electricメーカー250の使用説明書/サービス説明書
ページ先へ移動 of 27
MA GNUM ® PRO 250/350/450 AND 550 #$& ( #&W'V!") ! September , 2010 '276EJ 6A6?5D@? - @F Lincoln arc welding and cutting equipment is designed and built with safety in mind. However , your overall safety can be increased by proper installation .
#& "" A@H6C65 6BF:A>6?E 1.a. T urn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
:: '(- :: & & -' 42? 3FC? 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87.
::: '(- ::: #& (& - A@H6C65 6BF:A>6?E 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer ’s recommendations.
:G '(- :G $&M)(#"' 'U&(M Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques.
G G Thank Y ou for selecting a %) (- product by Lincoln Electric. W e want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! &625E9:D#A6C2E@CD !2?F2=4@>A=6E6=J before attempting to use this equipment.
( # #"("(' Page 6?6C2= 6D4C:AE:@? .
"& '&$(#" !")!R $&# !$ "&a.
"& '&$(#" !")!R $&# !$ !")!R.
"& '&$(#" !")!R $&# " !.
"'( (#" !")!R $&# !$ &625 E9:D6?E:C6 :?DE2==2E:@? D64E:@?.
"'( (#" !")!R $&# !$ b. Remove the molded gas plug fitting on the side of the feeder end handle and replace it with the barbed brass fit- ting provided in the kit.
"'( (#" "& "'( (#"" (&!!""'(&)(#"' Installation of (KP44 and KP44N series liners) a. Lay the gun and cable straight on a flat surface.
"'( (#" !")!R $&# !$ #"( (($"' "#.. "'( (#" a.
"'( (#" #""(#" ( # ($(&' Gun and cable assemblies which were assembled with a K466-5 connection kit will connect easily to an L-T ec feeder equipped with an L-T ec feeder connector assembly .
#$& (#" The MAGNUM® PRO 250, 350, 450 & 550 Amp guns and cables have been designed for use with Lincoln L- 50 and L-56, solid steel wire electrodes for the GMA W process and Lincoln Outershield cored electrodes for the gas-shielded FCA W process.
!"("" ! < The variation in cable lengths prevents the interchangeability of liners.
!"("" the outer jacket as shown in (Figure D.1). Be care- ful not to cut the insulation on the control wires while stripping jacket. Strip the red and white control leads 1/4 inch (6.4 mm) from the end and crimp a new S19492-2 terminal to each lead.
!"("" bly and connect the replacement control lead termi- nals. j. Position the cable boot and strain relief on the cable so it fits in cable handle cavity and lock the strain relief in place by pushing the two halves together .
!"("" strands with the threaded end out. Assemble incom- ing connector to cable by forcing the steel tube of the connector into the inside diameter of the cable inner tube until the copper strands are butted against the incoming connector shoulder .
(&#) '##(" !")!R $&# !$ If for any reason you do not understand t.
(&#) '##(" !")!R $&# !$ Observe all Safety Guidelines detailed th.
(&#) '##(" !")!R $&# !$ Observe all Safety Guidelines detailed throughout this manual.
"#(' !")!R $&# ".
READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES. SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE P ARA EL USO DE ESTE EQUIPO Y LOS CONSUMIBLES QUE V A A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE PARA ESTE EQUIP AMENTO E AS PAR TES DE USO, E SIGA AS PRÁ TICAS DE SEGURANÇA DO EMPREGADOR. + &"" *'# $&.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 441 17-1 199 U.S.A. TEL: 216.481.8100 F AX: 216.486.1751 WEB SITE: www .
デバイスLincoln Electric 250の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric 250をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric 250の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric 250の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric 250で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric 250を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric 250の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric 250に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric 250デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。