Lincoln ElectricメーカーDEMO ZONE IM709の使用説明書/サービス説明書
ページ先へ移動 of 22
Demo Zone ™ OPERA TOR’S MANUAL IM709 December, 2000 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCA UTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual and any others included with this equipment completely before attempting to use this equipment.
vi T ABLE OF CONTENTS Page Installation ................................................................................................................... ....Section A Technical Specifications ........................................................
A-1 INST ALLA TION DEMO ZONE A-1 TECHNICAL SPECIFICA TIONS - Demo Zone (K-1854-1) Voltage Specification Input Connection Specification 230 VAC single phase, 40 amps Type 6-50P plug ELECTRICAL INPUT REQUIREMENTS RA TED OUTPUT HEIGHT WIDTH DEPTH WEIGHT 53.
A-2 INST ALLA TION DEMO ZONE A-2 SAFETY PRECA UTIONS INPUT AND GR OUNDING CONNECTIONS INPUT PO WER The Demo Zone is designed to operate from 230 volt, 60 Hz single-phase input power with 40-amp capacity. A 6-50R type receptacle must be provided by the user.
A-3 INST ALLA TION DEMO ZONE A-3 INST ALLA TION OF FIELD INST ALLED OPTIONS CASTER WHEELS (P ART OF K1848-1) Caster wheels, which are provided, can be installed by lifting the Demo Zone approximately eight inches above ground level. Use the mounting hardware sup- plied to fasten the caster wheel to the mounting plate.
HANDLING A pallet jack or forklift truck can be used to move the Demo Zone and to install the caster kit. The place- ment of the pallet jack or forks must balance the Demo Zone load to prevent tipping. FALLING EQUIPMENT can cause injury. • Do not lift the Demo Zone by over- head crane.
B-1 OPERA TION B-1 GENERAL DESCRIPTION DEMO ZONE The Demo Zone is a compact system to display and demonstrate welding and cutting equipment. The Demo Zone contains: - Square Wave TIG 175 Power Source .
B-2 OPERA TION B-2 RECOMMENDED EQUIPMENT / INTERF A CE EQUIPMENT LIMIT A TIONS The Demo Zone is intended for indoor display and demonstration use. The Demo Zone is intended for light duty operation. Because of the input power limita- tion, power sources (except Ranger 250) may only be used at maximum output with low duty cycles.
B-3 OPERA TION B-3 WELDER OPERA TION DUTY CYCLE Full output and duty cycle may not be obtained from all power sources. The output and duty cycle may be limited by the 40 amp input power limitation of the Demo Zone. The duty cycle of the power source must be adjusted to be within the capability of the 40 amp input supply.
C-1 A CCESSORIES C-1 F A CT OR Y INST ALLED OPTIONS / A CCESSORIES - none FIELD INST ALLED OPTIONS / A CCESSORIES CASTER WHEELS Caster wheels, which are provided, are a field installed option for the Demo Zone. The 5-inch diame- ter caster wheels offer high mobility for in-shop use.
D-1 MAINTENANCE D-1 R OUTINE MAINTENANCE Refer to individual Operator’s Manuals for routine maintenance requirements. Perform the following daily routine: • Check that no combustible materials are in the weld- ing or cutting area or around the machine.
E-1 TR OUBLESHOO TING E-1 DEMO ZONE If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
F-1 DIA GRAMS F-1 DEMO ZONE DEMO ZONE WIRING DIAGRAM M19808 40A 40A LEAD CO LOR CODE: W = WH I TE B = B LACK G = GREEN 230 V INP UT C IRCUIT NOTES: MATERIAL: WIRE 8 AWG TYPE OR THHN OR THWN OR GAS AND.
NO TES DEMO ZONE.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TEN ÇÃ O Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS PAR TES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
デバイスLincoln Electric DEMO ZONE IM709の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Lincoln Electric DEMO ZONE IM709をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはLincoln Electric DEMO ZONE IM709の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Lincoln Electric DEMO ZONE IM709の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Lincoln Electric DEMO ZONE IM709で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Lincoln Electric DEMO ZONE IM709を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はLincoln Electric DEMO ZONE IM709の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Lincoln Electric DEMO ZONE IM709に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちLincoln Electric DEMO ZONE IM709デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。